battery MAZDA MODEL 626 2002 User Guide

5-32
Driving Your Mazda
Form No. 8Q50-EA-01G
Switches and Controls





Headlights
To turn on the lights, turn the knob on the
end of the control lever.





Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when any door is opened.





Headlight High-Low Beam
Push the lever forward for high beams.
Pull it back for low.





Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.
Lighting Control
Lever Position OFF
Headlights Off Off OnTaillights
Parking lights
License lights
Side-marker lights Off On On
NOTE
•
If the light switch is left on, the
lights will automatically switch off
30 seconds after turning the ignition
switch to the LOCK position or
removing the key.
The lights will automatically switch
back on when the ignition switch is
turned to the ACC or ON position.
• To prevent discharging the battery,
don ’t leave the lights on while the
engine is off.
Low beams High beams
J94S.book Page 32 Saturday, June 23, 2001 1:04 PM

6-20
Interior Comfort
Audio System
Form No. 8Q50-EA-01G





Power/Volume/Sound Controls
Power ON/OFF
Turn the ignition switch to the ACC or
ON position.
Press the power/volume knob to turn the
audio system on.
Press the power/volume knob again to
turn the audio system off. Volume adjustmentTo adjust the volume, turn the power/
volume knob.
Turn the power/volume knob to the right
to increase volume, to the left to decrease
it.
Display
Audio control knob
Power/Volume knob
NOTE
To prevent the battery from being
discharged, do not leave the audio
system on for a long period when the
engine is not running.
J94S.book Page 20 Saturday, June 23, 2001 1:04 PM

6-22
Interior Comfort
Audio System
Form No. 8Q50-EA-01G





Clock
Setting the time
The clock can be set at any time when the
ignition switch is in the ACC or ON
position.
1. To adjust the time, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock ’s current time will flash.
2. To advance the hours, press the hour set button ( ). To advance the
minutes, press the minute set button
( ) while the time is flashing.
3. Press the clock button ( ) again to start the clock. Exact hour adjustment 1. To set the exact hour, press the clock
button ( ) for about 2 seconds
until a beep is heard.
The clock ’s current time will flash.
2. Press the clock button ( ) again and the time will be adjusted as
follows:
(Example)
12:01 —12:29→ 12:00
12:30 —12:59→ 1:00
Display Clock button
Hour set
button
Minute set
button
NOTE
If the power supply to the unit is
interrupted (if the fuse blows or the
vehicle ’s battery is disconnected), the
clock will need to be reset.
J94S.book Page 22 Saturday, June 23, 2001 1:04 PM

6-24
Interior Comfort
Audio System
Form No. 8Q50-EA-01G





Operating the Radio
Radio ON
Press a band selector button ( or
) to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed. Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Turning the manual tuning knob will
change the frequency higher or lower.
Band selector buttons Display
Channel preset buttons Scan button
Auto memory
button
Manual tuning knob
Seek tuning:
Higher
frequency
Lower
frequency
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J94S.book Page 24 Saturday, June 23, 2001 1:04 PM

6-25
Interior Comfort
Audio System
Form No. 8Q50-EA-01G
Seek tuning
Pressing the seek tuning button
( , ) will cause the tuner to seek
a higher or lower frequency automatically.
Scan tuning
Press the scan button ( ) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, merely press
the scan button ( ) again during this
interval.
Preset channel tuning
The six preset channels can be used to
store 6 AM and 12 FM stations.
1. To set a channel first select AM, FM1, or FM2. Tune to the station you want.
2. Depress a channel preset button for about 2 seconds until a beep is heard.
The preset channel number and station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its
channel preset button. The station
frequency and the channel number will
be displayed. Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known. Additional AM/FM stations can
be stored without disturbing the
previously set channels.
Press and hold the auto memory button
( ) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store the six
strongest stations of each selected band in
that area.
After scanning is completed, the strongest
station will be tuned and its frequency
displayed.
Press and release the auto memory button
( ) to recall stations from the auto-
stored stations. One stored station will be
selected each time; its frequency and
channel number will be displayed.
NOTE
If you continue to press and hold the
button, the frequency will continue
changing without stopping.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
NOTE
If no stations can be tuned after
scanning operations, "A" will be
displayed.
J94S.book Page 25 Saturday, June 23, 2001 1:04 PM

6-38
Interior Comfort
Interior Equipment
Form No. 8Q50-EA-01G





Courtesy Light
Lights on when any door is open.





Accessory Socket
The ignition switch must be in the ACC or
ON position.
Only use genuine Mazda accessories or
the equivalent requiring no greater than
12V —10A.
Courtesy light
Accessories
To prevent accessory socket damage or
electrical failure, pay attention to the
following;
• Don ’t use accessories that require
more than 12V —10A.
• Don ’t use accessories that are not
genuine Mazda accessories or the
equivalent.
• Close the cover when the accessory
socket is not in use.
• Correctly insert the plug into the
accessory socket.
NOTE
To prevent discharging the battery,
don ’t use the socket for long periods
with the engine off or idling.
CAUTION
J94S.book Page 38 Saturday, June 23, 2001 1:04 PM

7-12
In Case of an Emergency
Form No. 8Q50-EA-01G
Emergency Starting
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and hold it there.
2. Turn the ignition switch to the START position and hold it there —for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it without using the accelerator—for up
to 10 seconds. Jump-starting is dangerous if done
incorrectly. So follow the procedure
carefully. If you feel unsure about jump-
starting, we strongly recommend that you
have a competent service technician do
the work.
Starting a Flooded EngineJump-Starting
Battery-Related Explosion:Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames, including
cigarettes, and sparks away from
open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one
with a low fluid level is dangerous. It
may rupture or explode, causing
serious injury.
Don’
t jump-start a frozen battery or
one with a low fluid level.
Use only a 12 V booster system. You
can damage a 12 V starter, ignition
system, and other electrical parts
beyond repair with a 24 V power
supply (two 12 V batteries in series or
a 24 V motor generator set).
WARNING
CAUTION
J94S.book Page 12 Saturday, June 23, 2001 1:04 PM

7-13
In Case of an Emergency
Emergency Starting
Form No. 8Q50-EA-01G
1. Make sure the booster battery is 12 V and that its negative terminal is
grounded.
2. If the booster battery is in another vehicle, don ’t allow the vehicles to
touch. Turn off the engine of the
vehicle with the booster battery and all
unnecessary electrical loads in both
vehicles.
3. Connect the jumper cables in the exact sequence as in the illustration.
•Connect one end of a cable to the
positive terminal on the discharged
battery (1).
• Attach the other end to the positive
terminal on the booster battery (2).
• Connect one end of the other cable
to the negative terminal of the
booster battery (3).
• Connect the other end to a solid,
stationary, exposed metallic point
(for example, the engine hanger)
away from the discharged battery
(4).
4. Start the engine of the booster vehicle and run it a few minutes. Then start the
engine of the other vehicle.
5. When finished, carefully disconnect the cables in the reverse order
described in Step 3.
Discharged
battery
Jumper cables Booster
battery
Connect cables in
numerical order
and disconnect in
reverse order. (+)
(-)
(+)
(-)
2.0-liter engine
Connecting to Negative Terminal:Connecting the end of the second
cable to the negative ( ) terminal
of the discharged battery is
dangerous.
A spark could cause the gas around
the battery to explode and injure
someone. Connect the cable to a point
away from the battery.
Connecting Jumper Cable to a
Moving Part:Connecting a jumper cable near or to
a moving part is dangerous. The cable
could get caught when the engine
starts and cause serious injury. Never
connect a jumper cable to or near any
part that moves.
Booster
battery
Discharged
battery
Jumper cables(+)
(-)
(+)
(-)
2.5-liter engineConnect cables in
numerical order
and disconnect in
reverse order.
WARNING
J94S.book Page 13 Saturday, June 23, 2001 1:04 PM

8-1
Form No. 8Q50-EA-01G
8Maintenance and Care
How to keep your Mazda in top condition.
Introduction ................................................................................. 8- 2
Introduction ............................................................................. 8- 2
Scheduled Maintenance .............................................................. 8- 3
Scheduled Maintenance ........................................................... 8- 3
Owner Maintenance .................................................................... 8- 7
Owner Maintenance Schedule ................................................. 8- 7
Owner Maintenance Precautions ............................................. 8- 8
Engine Compartment Overview .............................................. 8- 9
Engine Oil ................................................................................ 8-10
Engine Coolant ........................................................................ 8-13
Brake/Clutch Fluid .................................................................. 8-15
Power Steering Fluid ............................................................... 8-17
Automatic Transaxle Fluid (ATF) ........................................... 8-18
Washer Fluid ............................................................................ 8-20
Body Lubrication ..................................................................... 8-21
Air Filter .................................................................................. 8-21
Wiper Blades ........................................................................... 8-22
Battery ..................................................................................... 8-24
Tires ......................................................................................... 8-25
Light Bulbs .............................................................................. 8-29
Fuses ........................................................................................ 8-35
Appearance Care ......................................................................... 8-40
How to Minimize Environmental Paint Damage ..................... 8-40
Exterior Care ........................................................................... 8-42
Interior Care ............................................................................ 8-45
J94S.book Page 1 Saturday, June 23, 2001 1:04 PM

8-9
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Engine Compartment Overview
2.0-liter engineAutomatic transaxle fluid-level
dipstick (only for automatic
transaxle)
Brake/Clutch fluid reservoir
Battery Fuse block
Engine coolant
reservoirAir filter
Cooling system cap Engine oil-filler cap
Power steering fluid
reservoir
Windshield washer
fluid reservoir Engine oil dipstick
2.5-liter engine
Air filter
Cooling system cap
Engine coolant reservoir
Power steering fluid
reservoir
Battery
Fuse block
Automatic transaxle fluid-level
dipstick (only for automatic
transaxle)
Brake/Clutch fluid reservoir
Engine oil-filler cap
Windshield washer
fluid reservoir Engine oil dipstick
J94S.book Page 9 Saturday, June 23, 2001 1:04 PM