flat tire MAZDA MODEL 626 2002 User Guide

7-8
In Case of an Emergency
Flat Tire
Form No. 8Q50-EA-01G
2. Mount the spare tire.
3. Install the lug nuts with the beveled edge inward; tighten them by hand. 4. Turn the lug wrench counterclockwise
and lower the vehicle. Use the lug
wrench to tighten the nuts in the order
shown.
If you ’re unsure of how tight the nuts
should be, have them inspected at a
service station.
Nut tightening torque:
Removing Dirt and Grime from Wheels, Hubs and Hub Bolts:When changing or replacing a tire,
not removing dirt and grim from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
WARNING
Applying Oil and Grease to Lug Nuts, Bolts:Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the
tire to come off, resulting in an
accident. In addition, lug nuts and
bolts could be damaged if tightened
more than necessary. Do not apply oil
or grease to lug nuts and bolts and do
not tighten the lug nuts beyond the
recommended tightening torque.
N· m (kgf ·m, ft ·lbf) 90 —120 (9—12, 65—87)
WARNING
J94S.book Page 8 Saturday, June 23, 2001 1:04 PM

7-9
In Case of an Emergency
Flat Tire
Form No. 8Q50-EA-01G
5. Store the damaged tire in the trunk. Have the damaged tire repaired as soon
as possible.
Loose Lug Nuts:Improperly or loosely tightened lug
nuts are dangerous. The wheel could
wobble or come off. This could result
in loss of vehicle control and cause a
serious accident. Always securely and
correctly tighten the lug nuts.
Metric Studs and Lug Nuts:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip
off and cause an accident. Be sure to
reinstall the same nuts you removed
or replace them with metric nuts of
the same configuration.
Incorrect Tire Air Pressure:
Driving on tires with incorrect air
pressure is dangerous. Tires with
incorrect pressure could affect
handling and result in an accident.
Don ’t drive with any tires that have
incorrect air pressure. When you
check the regular tires ’ air pressure,
check the spare tire, too.
NOTE
To prevent the jack and tool from
rattling, store them properly.
WARNING
J94S.book Page 9 Saturday, June 23, 2001 1:04 PM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8Q50-EA-01G





Schedule 2
I : Inspect and repair, clean, adjust, or replace if necessary.
(Oil-permeated air filter cannot be cleaned using the air-blow method.) R: Replace
L : Lubricate
*1: According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometrage (mileage) period to ensure long-term reliability.
*2: If the vehicle is operated in cold districts { below –18 degrees C (0 degrees F) }, replace the timing belt at 96,000km (60,000miles).
Maintenance
Interval
Maintenance
Item Number of months or kilometers (miles), whichever comes first Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 Km 8 1624324048566472808896
(×1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60)
Engine valve clearance I
Drive belts (tension) II
Engine timing belt
*2Inspect at 96,000km (60,000miles)
Replace every 168,000km (105,000miles)
Engine oil Puerto Rico
Replace every 5,000km (3,000miles) or 3 months
others RRRRRRRRRRRR
Engine oil filter RRRRRRRRRRRR
Cooling system II
Engine coolant Replace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Engine coolant level IIIIIIIIIIII
Idle speed II
Air filter I
*1RI *1R
Fuel lines and hoses*1II
Hoses and tubes for emission*1I
Spark plugs 2.0-liter engine
(non-PLATINUM tipped type)
RR
2.5-liter engine
(PLATINUM tipped type) Replace every 96,000km (60,000miles)
Function of all lights IIIIIIIIIIII
Brake lines, hoses and connections II
Brake and clutch fluid level IIIIIIIIIIII
Disc brakes IIII
Drum brakes II
Tire inflation pressure and tire wear IIIIIIIIIIII
Steering operation and linkages II
Power steering fluid level IIIIIIIIIIII
Front suspension ball joints II
Driveshaft dust boots II
Bolts and nuts on chassis and body IIII
Exhaust system heat shields II
All locks and hinges LLLLLLLLLLLL
08.fm Page 5 Monday, June 25, 2001 5:12 PM

8-7
Maintenance and Care
Form No. 8Q50-EA-01G
Owner Maintenance
The owner or a qualified service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.
Bring any problem to the attention of an Authorized Mazda Dealer or qualified service
technician as soon as possible.





When Refueling
• Brake and clutch fluid level (page 8-15)
• Engine coolant level (page 8-13)
• Engine oil level (page 8-11)
• Washer fluid level (page 8-20)






At Least Monthly
• Tire inflation pressures (page 8-26)






At Least Twice a Year (For Example, Every Spring and Fall)
• Automatic transaxle fluid level (page 8-18)
• Power steering fluid level (page 8-17)
You can do the following scheduled maintenance items if you have some mechanical
ability and a few basic tools and if you closely follow the directions in this manual.
• Air filter (page 8-21)
• Engine coolant (page 8-13)
• Engine oil (page 8-11)
Owner Maintenance Schedule
J94S.book Page 7 Saturday, June 23, 2001 1:04 PM

8-25
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Battery Maintenance
To get the best service from a battery:
• Keep it securely mounted.
• Keep the top clean and dry.
• Keep terminals and connections clean,
tight, and coated with petroleum jelly
or terminal grease.
• Rinse off spilled electrolyte
immediately with a solution of water
and baking soda.
• If the vehicle will not be used for an
extended time, disconnect the battery
cables. For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tire inflation pressures and
stay within the recommended load limits
and weight distribution.
Tires
Using Different Tire Types:Driving your vehicle with different
types of tires is dangerous. It could
cause poor handling and poor
braking; leading to loss of control.
Except when using the temporary
spare tire, use only the same type tires
(radial, bias-belted, bias-type) on all
four wheels.
Using Wrong-Sized Tires:
Using any other tire size than what is
specified for your Mazda (page 10-6)
is dangerous. It could seriously affect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size specified for your
Mazda.
WARNING
J94S.book Page 25 Saturday, June 23, 2001 1:04 PM

8-26
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Tire Inflation Pressure
Inspect all tire pressures monthly
(including the spare) when the tires are
cold. Maintain recommended pressures
for the best ride, top handling, and
minimum tire wear.
Refer to the specification charts (page 10-
6).
Incorrect Tire Inflation:Overinflation or underinflation of
tires is dangerous. Adverse handling
or unexpected tire failure could result
in a serious accident. Always inflate
the tires to the correct pressure (page
10-6).
WARNING
NOTE
• Warm tires normally exceed
recommended pressures. Don ’t
release air from warm tires to adjust
the pressure.
• Underinflation can cause reduced
fuel economy and poor sealing of
the tire bead, which will deform the
wheel and cause separation of tire
from rim.
• Overinflation can produce a harsh
ride and a greater possibility of
damage from road hazards.
Keep your tire pressure at the
correct levels. If one frequently
needs inflating, have it inspected.
J94S.book Page 26 Saturday, June 23, 2001 1:04 PM

8-28
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Temporary Spare Tire
Inspect the temporary spare tire at least
monthly to make sure it ’s properly
inflated and stored.
The temporary spare tire is easier to
handle because of its construction. It is
lighter and smaller than a conventional
tire and should be used only for an
emergency and only for a short distance.
Use the temporary only until the
conventional tire is repaired, which should
be as soon as possible.
Maintain its pressure at 420 kPa (60 psi).





Replacing a Wheel
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset.
Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and flat spots.
• Don ’t use your temporary spare tire
rim with a snow tire or a
conventional tire. Neither will
properly fit and could damage both
tire and rim.
• The temporary spare tire has a tread
life of up to 5,000 km (3,000 miles),
depending on road conditions and
driving habits.
• When the tread wear solid-band
indicator appears, replace the tire
with the same type of temporary
spare.
CAUTION
Using a Wrong-Sized Wheel:Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident. Always use
wheels of the correct size on your
vehicle.
A wrong-sized wheel may adversely
affect
•Tire fit
• Wheel and bearing life
• Ground clearance
• Snow-chain clearance
• Speedometer calibration
• Headlight aim
• Bumper height
WARNING
CAUTION
J94S.book Page 28 Saturday, June 23, 2001 1:04 PM

9-13
Customer Information
Uniform Tire Quality Grading System (UTQGS)
Form No. 8Q50-EA-01G
These grades will be added to the sidewalls of passenger vehicle tires over the next several
years according to a schedule established by the NHTSA and the tire manufacturers.
The grade of tires available as standard or optional equipment on Mazda vehicle may vary
with respect to grade.
ALL PASSENGER VEHICLE TIRES MUST CONFORM TO THESE GRADES AND
TO ALL OTHER FEDERAL TIRE-SAFETY REQUIREMENTS.





Uniform Tire Quality Grading
Quality grades can be found where applicable on the tire sidewall between tread shoulder
and maximum section width.
For example:
Treadwear 200 Traction AA Temperature A
The temperature grade for this tire is established for a tire that is properly inflated
and not overloaded. Excessive speed, underinflation, or excessive loading, either
separately or in combination, can cause heat buildup and possible tire failure.
WARNING
UTQGS MARK (example)
TREADWEAR 200 TRACTION AA
TEMPERATURE A
J94S.book Page 13 Saturday, June 23, 2001 1:04 PM

10-6
Specifications
Form No. 8Q50-EA-01G





Air Conditioner






Light Bulbs






Tires
Standard tire
Temporary spare tire
Fuses ................................................................................................................ Refer to 8-35
Gas complies with SAE J639 R-134a
Maximum operating charge 0.75 kg (26.5 oz)
Light bulb Wattage
Headlights 60/55
Front turn signal/Parking lights 27/8
Rear-turn signal lights 27
Brake lights/Taillights 27/7
High-mount brake lights 27
Reverse lights 18
License plate lights 5
Trunk light 5
Interior lights 10
Map light 5
Courtesy lights 5
Item
Ty p e Tire size
Inflation pressure kgf/cm
2(psi or lb/po 2)
Front Rear
2.0-liter engine P205/60R15 90H 2.2 (32)1.8 (26)
2.5-liter engine P205/60R15 90H
P205/55R16 89H 2.0 (29)
Tire size Inflation pressure kPa (psi)
T125/70D15 420 (60)
J94S.book Page 6 Saturday, June 23, 2001 1:04 PM

11-3
Index
Form No. 8Q50-EA-01G
D
Driving Tips ....................................... 4-7
Automatic transaxle
.................. 5-12
Break-in period
........................... 4-7
Driving in flooded area
............. 4-10
Hazardous driving
....................... 4-8
Money-saving suggestions
.......... 4-7
Rocking the vehicle
.................... 4-8
Trailer towing
........................... 4-11
Winter driving
............................. 4-9
E
Emergency Starting .......................... 7-12
Flooded engine
.......................... 7-12
Jump-starting
............................ 7-12
Push-starting
............................. 7-14
Emergency Towing
.......................... 7-15
Emission Control System
................... 4-4
Engine Coolant
...................................... 8-13
Exhaust gas
................................. 4-5
Hood release
............................... 3-9
Oil
............................................. 8-10
Overheating
............................... 7-10
Starting
........................................ 5-3
Engine Compartment Overview
........ 8-9
Engine Coolant Overheating
............................... 7-10
Engine Coolant Temperature
Gauge
............................................... 5-21
Exhaust Gas
....................................... 4-5
Exterior Care
.................................... 8-42
Eyeglass Holder
............................... 6-41
F
Flasher Hazard warning
.........................5-36
Headlights
.................................5-32
Flat Tire
..............................................7-3
Changing
.....................................7-5
Spare tire and tool storage
...........7-3
Fluids Classification
.............................10-4
Owner maintenance
.....................8-7
Foot Brake
..........................................5-4
Front seats
..........................................2-2
Fuel Filler lid and cap
.......................3-14
Gauge
........................................5-22
Requirements
..............................4-2
Tank capacity
............................10-5
Fuses
.................................................8-35
Panel description
.......................8-37
Replacement
..............................8-35
G
Gauges ..............................................5-19
Glove Box
........................................6-42
H
Hazard Warning Flasher ...................5-36
Hazardous Driving
.............................4-8
Headlights Control
......................................5-32
Flashing
.....................................5-32
High-low beam
..........................5-32
On reminder
..............................5-32
Hood Release
......................................3-9
Horn
..................................................5-36
J94S.book Page 3 Saturday, June 23, 2001 1:04 PM