belt MAZDA MODEL 626 2002 Owner's Manual

2-23
Essential Safety Equipment
Child Restraint
Form No. 8Q50-EA-01G





If You Must Use the Front Seat
for Children
If you cannot put all children in the rear
seat, at least put the smallest in the rear
seat and be sure the largest child up front
uses the shoulder belt over the shoulder.
Do not put rear-facing child-restraint
systems on the front passenger ’s seat.
This seat is also not set up for tethered
child-restraint systems, put them in one of
the three rear seat positions set up with
tether anchors.
Don ’t allow anyone to sleep against the
right front door if you have an optional
side air bag, it could cause serious injuries
to an out of position occupant. As
children more often sleep in cars, it is
better to put them in the rear seat. If
installing the child-restraint system on the
front seat is unavoidable, follow these
instructions when using a front-facing
child-restraint system in the front
passenger ’s seat.
NOTE
To check if your Mazda front seats
have side air bags:
Every Mazda side air bag will have a
"SRS-Air Bag" label on the outboard
shoulder of the front seats.
Front Passenger ’s Seat Position:As your vehicle has front air bags and
doubly so because your vehicle has
side air bags, a front-facing child-
restraint system should be put on the
front seat only when it is unavoidable.
Always move the seat as far back as
possible, because the force of a
deploying air bag could cause serious
injury or death to the child.
Rear-Facing Child-Restraint System:
Rear-facing child-restraint systems
on the front seat are particularly
dangerous.
The child-restraint system can be hit
by a deploying air bag and moved
violently backward resulting in
serious injury or death to the child.
NEVER use a rear-facing child-
restraint system in the front seat with
an air bag that could deploy.
WARNING
J94S.book Page 23 Saturday, June 23, 2001 1:04 PM

2-24
Essential Safety Equipment
Child Restraint
Form No. 8Q50-EA-01G





Front Passenger ’s Seat Child-
Restraint System Installation
1. Slide the seat as far back as possible.
2. Secure the child-restraint system with
the lap portion of the lap/shoulder belt.
See the instructions on the child-
restraint system for belt routing
instructions. 3. To get the retractor into the automatic
locking mode, pull the shoulder belt
portion of the seat belt until the entire
length of the belt is out of the retractor.
4. Push the child-restraint system firmly into the vehicle seat. Be sure the belt
retracts as snugly as possible. Clicking
from the retractor will be heard during
retraction if the system is in automatic
locking mode. If the belt does not lock
the seat down tight, repeat this step.
Children and Seating Position with Side Air Bag:Allowing anyone to lean over or
against the front door is dangerous. If
the vehicle is equipped with side air
bags, the impact of an inflating side
air bag could cause serious injury or
death to the person. Children are
more likely to sleep in the vehicle;
when they do, they are more at risk in
the front passenger ’s seat that has a
side air bag because they may slump
over into the path of the seatback-
mounted air bag. If a child can ’t be
seated in the rear, do not allow the
child to lean over or against the front
door, even if the child is seated in a
child-restraint system.
WARNING
NOTE
• Inspect this function before each
use of the child-restraint system.
You should not be able to pull the
shoulder belt out of the retractor
while the system is in the automatic
locking mode. When you remove
the child-restraint system, be sure
the belt fully retracts to return the
system to emergency locking mode
before occupants use the seat belts.
• Follow the child-restraint system
manufacturer ’s instruction carefully.
Depending on the type of child-
restraint system, it may not employ
seat belts which are in automatic
locking mode.
J94S.book Page 24 Saturday, June 23, 2001 1:04 PM

2-25
Essential Safety Equipment
Form No. 8Q50-EA-01G
SRS Air Bags
Read this owner’s manual carefully to verify what air bags (driver-side air bag, passenger-
side air bag, side air bags) are equipped in your vehicle.
The front and side supplemental restraint systems (SRS) include 4 air bags.
They are located in:
• The steering wheel
• The passenger side dashboard
• The outboard sides of the front seatbacks
These systems operate independently depending on the type of accident encountered; both
side air bags are not likely to deploy in the same accident because a vehicle is not often hit
from both sides. The front and side air bag systems will not normally deploy during the
same type of accident unless a combination of frontal and side impacts occur.
In a front-end or side impact, the air bag supplemental restraint systems are designed to
provide only supplemental protection for the driver and front seat passenger. Seat belts
must still be worn.
Without seat belt usage, the air bags cannot provide adequate protection during an
accident. Seat belt usage is necessary to:
• Keep the passenger away from an inflating air bag.
• Reduce the possibility of injuries during an accident that is not designed for air bag
inflation, such as roll-over or rear impact.
• Reduce the possibility of injuries in frontal or side collisions that are not severe enough
to activate the air bags.
• Reduce the possibility of being thrown from your vehicle.
• Reduce the possibility of injuries to lower body and legs during an accident because the
air bags provide no protection to these parts.
• Hold the driver in a position which allows better control of the vehicle.
Small children, those under 18 kg (40 lb), should be protected by a child-restraint system
(page 2-18).
Supplemental Restraint Systems (SRS) Precautions
J94S.book Page 25 Saturday, June 23, 2001 1:04 PM

2-26
Essential Safety Equipment
SRS Air Bags
Form No. 8Q50-EA-01G
Air Bags without Seat Belts:Depending only on the air bags for protection during an accident is dangerous.
Alone, air bags may not prevent serious injuries. The appropriate air bags can be
expected to inflate only during a frontal, side or near-frontal collision of at least
moderate force. Vehicle occupants should always wear seat belts.
Child in the Front Seat:
Placing a child, 12 years or under, in the front seat is dangerous. The child could be
hit by a deploying air bag and be seriously injured or even killed. A sleeping child is
more likely to lean against the door and be hit by the side air bag in a moderate, right-
side collision. Whenever possible, always secure a child 12 years and under on the
rear seat with an appropriate child-restraint system for the child’s age and size.
Rear-Facing Child-Restraint System:
Rear-facing child-restraint systems on the front seat are particularly dangerous.
The child-restraint system can be hit by a deploying air bag and moved violently
backward resulting in serious injury or death to the child. NEVER use a rear-facing
child-restraint system in the front seat with an air bag that could deploy.
Seating Position with Front Air Bags:
Sitting too close to the air bag storage compartments or placing hands or feet on them
is extremely dangerous. Front Air bags inflate with great force and speed. Serious
injuries could occur if someone is too close. The driver should always hold onto only
the rim of the steering wheel. The front seat passenger should keep both feet on the
floor. Front seat occupants should adjust their seats as far back as possible and
always sit upright against the seatbacks with seat belts worn properly.
WARNING
Deploying air bag
J94S.book Page 26 Saturday, June 23, 2001 1:04 PM

2-27
Essential Safety Equipment
SRS Air Bags
Form No. 8Q50-EA-01G
Seating Position with Side Air Bags:Sitting too close to the side air bag storage compartments or placing hands on them is
extremely dangerous. A side air bag inflates with great force and speed directly out of
the outboard shoulder of the front seat and expands along the front door on the side
the car is hit.
Serious injury could occur if someone is sitting too close to the door or leaning
against a window in the front seats or if rear seat occupants grab the sides of the
seatbacks. Furthermore, sleeping up against the door or hanging out the driver’s-side
window while driving could block the side air bag and eliminate the advantages of
supplemental protection. Give the side airbags room to work by sitting in the center of
the seat while the vehicle is moving with seat belts worn properly.
Front Air Bag Storage Areas:
Attaching an object to a front air bag storage area or placing something in front of it
is dangerous. In an accident, the object could interfere with front air bag inflation
and injure the occupants.
Always keep the front air bag storage areas free of objects.
Side Air Bag Storage Areas:
Attaching things to the seat in such a way as to cover the outboard side of the seat in
any way is dangerous. In an accident the object could interfere with the side air bag,
which inflates from the outboard side of the front seats, impeding the added
protection of the side air bag system or redirecting the air bag in a way that is
dangerous. Furthermore, the bag could be cut open spewing exhaust.
Do not hang net bags, map pouches or back pads with side straps on the front seats.
Always keep the side air bag storage areas in your front seats free to deploy in the
event of a side collision.
Hot Air Bag Inflators:
Hot air bag inflators are dangerous. Immediately after inflation, the inflators in the
steering wheel, dashboard or the seatbacks are very hot. You could get burned. Don ’t
touch the internal components of the air bag storage areas after the bags have
inflated.
Installation of Front-End Equipment:
Installation of front-end equipment, such as frontal protection bar (kangaroo bar,
bull bar, push bar, etc.), snowplow, or winches, is dangerous. The air bag crash sensor
system could be affected. This could cause air bags to inflate unexpectedly, or it could
prevent the air bags from inflating during an accident. Front occupants could be
seriously injured. Never install any front-end equipment to your vehicle.
WARNING
J94S.book Page 27 Saturday, June 23, 2001 1:04 PM

4-6
Before Driving Your Mazda
Form No. 8Q50-EA-01G
Before Starting the Engine
•Be sure the windows, outside
mirror (s), and outside lights are clean.
• Inspect inflation pressures and
condition of tires.
• Look under the vehicle for any sign of
a leak.
• If you plan to back up, make sure
nothing will be in your way. •
Are all doors closed and locked?
• Are the inside and outside mirrors
adjusted?
• Is everyone ’s seat belt fastened?
• Do all the lights work?
• Check all gauges.
• Check all warning lights when the
ignition switch is turned to the ON
position.
• Release the parking brake and make
sure the parking brake warning light
goes off.
Always be thoroughly familiar with your
Mazda.
Before Getting In
NOTE
Engine oil, engine coolant, brake/
clutch fluid, washer fluid, and other
fluid levels should be inspected daily,
weekly, or at refueling, depending on
the fluid. See Maintenance, Section 8.
After Getting In
J94S.book Page 6 Saturday, June 23, 2001 1:04 PM

5-3
Driving Your Mazda
Starting and Driving
Form No. 8Q50-EA-01G
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
ON
This is the normal running position after
the engine is started. The warning lights
(except brakes)should be inspected before
the engine is started (page 5-23).
START
The engine is started in this position. It
will crank until you release the key; then
it returns to the ON position. The brake
warning light can be checked after the
engine is started (page 5-23).





Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened. 1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4. (Manual transaxle)
Depress the clutch pedal all the way
and shift into neutral.
Keep the pedal depressed while
cranking the engine.
NOTE
If turning the key is difficult, jiggle the
steering wheel from side to side.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
The starter will not operate if the
clutch pedal is not pushed down all the
way.
J94S.book Page 3 Saturday, June 23, 2001 1:04 PM

5-23
Driving Your Mazda
Form No. 8Q50-EA-01G
Warning/Indicator Lights and Beeps
Warning/Indicator Lights
SignalWarning/Indicator Lights Page
Brake System Warning Light 5-25
Seat Belt Warning Light 5-25
Charging System Warning Light 5-26
Engine Oil Pressure Warning Light 5-26
TCS Warning Light 5-27
Low Fuel Warning Light 5-27
Low Washer Fluid Level Warning Light 5-27
Warning/Indicator lights will appear in any of the highlighted areas
J94S.book Page 23 Saturday, June 23, 2001 1:04 PM

5-25
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q50-EA-01G





Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-15).
2. After adding fluid, check the light again.
If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer.
Even if the light goes off, have your brake
system inspected as soon as possible.





Seat Belt Warning Light/Beep
If the driver ’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds and the seat belt warning light
will remain on until the belt is fastened.
If the system does not operate correctly,
consult an Authorized Mazda Dealer.
Brake Warning Light:Driving with the brake system
warning light on is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this
light remains on, have the brakes
inspected immediately. Don ’t drive
with this light on, and contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible.
WARNING
J94S.book Page 25 Saturday, June 23, 2001 1:04 PM

5-26
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q50-EA-01G





Charging System Warning Light
This warning light indicates a malfunction
of the alternator or of the charging system.
If the light comes on while driving:
1. Drive to the side of the road and park
off the right-of-way.
2. Turn off the engine. Inspect the alternator drive belt for looseness and
breakage.
3. If it ’s OK, the charging system has a
problem. Consult an Authorized
Mazda Dealer as soon as possible.





Engine Oil Pressure Warning
Light
This warning light indicates low engine
oil pressure.
If the light comes on while driving:
1. Drive to the side of the road and park
off the right-of-way.
2. Turn off the engine and inspect the engine oil level (page 8-11). If it ’s low,
add oil.
3. Check the light.
If the light remains on even after you add
oil, have your vehicle towed to the nearest
service station or to an Authorized Mazda
Dealer.
Don
’t drive with a loose or broken
alternator belt. The engine could
overheat because this belt also drives
the water pump.
CAUTION
Don ’t run the engine if oil pressure is
low. It could result in extensive engine
damage.
CAUTION
J94S.book Page 26 Saturday, June 23, 2001 1:04 PM