ESP MAZDA MODEL CX-3 2015 (in English) Owner's Manual

4–181
When Driving
Parking Sensor System
Rear Corner Sensor
Distance detection area Distance between vehicle and obstruction Beeper sound *1
Far distance Approx. 50—38 cm (19—14 in) Medium intermittent sound
Middle distance Approx. 38—25 cm (14.0—9.8 in)
Fast intermittent sound
Close distance Within approx. 25 cm (9.8 in)
Continuous sound
*1 The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.
NOTE
If an obstruction is detected in a zone for 6 seconds or more, the beep sound is stopped
(except for the close-distance zone). If the same obstruction is detected in another zone,
the corresponding beep sound is heard.
$9@&;&&%@&EJUJPOJOEC







5–33
Interior Features
Audio System
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel fi rst select AM, FM1,
or FM2. Tune to the desired station.
2. Press a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number or station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other
stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its channel
preset button. The station frequency or
the channel number will be displayed.
Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known.
Press and hold the auto memory button
(
) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed. Press and
release the auto memory button (
)
to recall stations from the auto-stored
stations. One stored station will be
selected each time and its frequency and
channel number will be displayed.
NOTE
If no stations can be tuned after scanning
operations, “ A ” will be displayed.
$9@&;&&%@&EJUJPOJOEC







5–112
Interior Features
Bluetooth®
Audio Operation Using Voice Recognition (Type C/Type D)
Main audio operation
The below commands are examples of the available commands.
When the talk button is pressed and the following command is spoken out, the audio can be
operated. The commands in the () can be omitted. The specifi ed name and number are put
into the {}.
Voice command Function Corresponding audio
source
(Go to/Play) AM (Radio) Switches the audio source to AM radio. All
(Go to/Play) FM (Radio) Switches the audio source to FM radio. All
(Go to/Play) DAB (Radio) Switches the audio source to DAB radio. All
(Go to/Play) Bluetooth (Audio) Switches the audio source to BT audio. All
(Go to/Play) Aha (Radio) Switches the audio source to Aha™ Radio. All
(Go to/Play) Stitcher Switches the audio source to Stitcher™ Radio. All
(Go to/Play) USB 1 Switches the audio source to USB 1. All
(Go to/Play) USB 2 Switches the audio source to USB 2. All
Play Playlist {Playlist name} Plays the selected playlist. USB
Play Artist {Artist name} Plays the selected artist. USB
Play Album {Album name} Plays the selected album. USB
Play Genre {Genre name} Plays the selected genre. USB
Play Folder {Folder name} Plays the selected folder. USB
NOTE
  Some commands cannot be used depending on devices and use conditions. 
 If the Bluetooth ® device, USB, or AUX is not connected, the related commands cannot
be used.
$9@&;&&%@&EJUJPOJOEC







5–125
Interior Features
Bluetooth®
4. Download will be started from the
mobile phone.
NOTE
  Attached data is not downloaded. 
 Messages up to 1 kilobyte
(e-mail)/140-bytes (SMS) can be
downloaded.
  A message list is created for each
device.
  If the connected device does not
correspond to MAP 1.0, the AT
command is used to download. The
downloaded message indicates that it
is already read.
  Downloading using the AT command
may not function depending on the
connected device.
Receiving messages
(Method 1)
When a device receives a message, a
message received notifi cation is displayed.
The “Email Notifi cations” (E-mail) or
“SMS Notifi cations” (SMS) setting must
be on.
Refer to Communication Settings on page
5-128 .
Select
and display the message.
(Method 2)
1. Select the
icon on the home screen
and display the Communication screen.
2. Select
and display the new
message list for e-mail and SMS.
3. Select the message you would like to
display.
$9@&;&&%@&EJUJPOJOEC







*Some models.5–129
Interior Features
Bluetooth®
Bluetooth ® Audio (Type
A/Type B)
*
Applicable Bluetooth ® specifi cation
(Recommended)
Ver. 2.0
Response profi le




 A2DP (Advanced Audio Distribution
Profi le) Ver. 1.0/1.2




 AVRCP (Audio/Video Remote Control
Profi le) Ver. 1.0/1.3
A2DP is a profi le which transmits only
audio to the Bluetooth
® unit. If your
Bluetooth® audio device corresponds
only to A2DP, but not AVRCP, you
cannot operate it using the control panel
of the vehicle's audio system. In this
case, only the operations on the mobile
device are available the same as when a
portable audio device for a non-compliant
Bluetooth
® device is connected to the
AUX terminal.
Function A2DP AVRCP
Ver. 1.0 Ver. 1.3
Playback — X X
Pause — X X
File (Track) up/down — X X
Reverse — — X
Fast-forward — — X
Text display — — X
X: Available
—: Not available
NOTE
  The battery consumption of
Bluetooth® audio devices increases
while Bluetooth ® is connected.   If a general mobile phone device
is USB connected during music
playback over the Bluetooth
®
connection, the Bluetooth ®
connection is disconnected. For
this reason, you cannot have
music playback over a Bluetooth
®
connection and music playback using
a USB connection at the same time.
  The system may not operate
normally depending on the
Bluetooth
® audio device.
How to Use the Bluetooth ® Audio
System
Switching to Bluetooth ® audio mode
To listen to music or voice audio recorded
to a Bluetooth
® audio device, switch to
the Bluetooth ® audio mode to operate
the audio device using the audio system
control panel. Any Bluetooth
® audio
device must be paired to the vehicle's
Bluetooth
® unit before it can be used.
Refer to Bluetooth ® Preparation (Type A/
Type B) on page 5-92 .
1. Turn on the Bluetooth
® audio device's
power.
2. Switch the ignition to ACC or ON.
Make sure that the “
” symbol is
displayed in the audio display. The
symbol is not displayed if an un-paired
Bluetooth
® audio device is being used
or the vehicle's Bluetooth ® unit has a
malfunction.
$9@&;&&%@&EJUJPOJOEC







*Some models.5–131
Interior Features
Bluetooth®
Display scroll
Only 13 characters can be displayed at one
time. To display the rest of the characters
of a long title, press and hold the text
button (3). The display scrolls the next 13
characters. Press and hold the text button
(3) again after the last 13 characters have
been displayed to return to the beginning
of the title.
Bluetooth ® Audio Device
Information Display
If a Bluetooth ® audio device is connected,
the following information is displayed in
the audio display.
AVRCP Ver.
lower than 1.3 AVRCP
Ver. 1.3
Device name X X
Title — X
Artist name — X
Album name — X
File number — X
Playback time — X
Folder number — —
X: Available
—: Not available
NOTE
Some information may not display
depending on the device, and if the
information cannot be displayed, “ NO
TITLE” is indicated.
Bluetooth ® Audio (Type
C/Type D)
*
Applicable Bluetooth ® specifi cation
(Recommended)
Ver. 1.1/1.2/2.0
EDR/2.1 EDR/3.0
(conformity)
Response profi le




 A2DP (Advanced Audio Distribution
Profi le) Ver. 1.0/1.2




 AVRCP (Audio/Video Remote Control
Profi le) Ver. 1.0/1.3/1.4
A2DP is a profi le which transmits only
audio to the Bluetooth
® unit. If your
Bluetooth® audio device corresponds
only to A2DP, but not AVRCP, you
cannot operate it using the control panel
of the vehicle's audio system. In this
case, only the operations on the mobile
device are available the same as when a
portable audio device for a non-compliant
Bluetooth
® device is connected to the
AUX terminal.
$9@&;&&%@&EJUJPOJOEC







6–2
Maintenance and Care
Essential Information
Introduction
Be extremely careful and prevent injury to yourself and others or damage to your vehicle
when using this manual for inspection and maintenance.
If you are unsure about any procedure it describes, we strongly urge you to have a reliable
and qualifi ed technician perform the work, we recommend an Authorised Mazda Repairer.
Authorised Mazda technicians and genuine Mazda parts are dedicated to your vehicle.
Without this expertise and the parts that have been designed and made especially for your
Mazda, inadequate, incomplete, and insuffi cient servicing may result in problems. This
could lead to vehicle damage or an accident and injuries.
For expert advice and quality service, consult an expert repairer, we recommend an
Authorised Mazda Repairer.
The owner should retain evidence that proper maintenance has been performed as
prescribed.
A claim against a warranty will not qualify if it results from lack of maintenance and not
from defective material or authorised workmanship.
$9@&;&&%@&EJUJPOJOEC







6–18
Maintenance and Care
Owner Maintenance
WARNING
Do not perform maintenance work if you lack suffi cient knowledge and experience
or the proper tools and equipment to do the work. Have maintenance work done by a
qualifi ed technician:
Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedures.
If you must run the engine while working under the bonnet, make certain that you
remove all jewellery (especially rings, bracelets, watches, and necklaces) and all
neckties, scarves, and similar loose clothing before getting near the engine or cooling
fan which may turn on unexpectedly:
Working under the bonnet with the engine running is dangerous. It becomes even more
dangerous when you wear jewellery or loose clothing.
Either can become entangled in moving parts and result in injury.
Switch the ignition to off and make sure the fan is not running before attempting
to work near the cooling fan:
Working near the cooling fan when it is running is dangerous. The fan could continue
running indefi nitely even if the engine has stopped and the engine compartment
temperature is high. You could be hit by the fan and seriously injured.
Do not leave items in the engine compartment:
After you have fi nished checking or doing servicing in the engine compartment, do not
forget and leave items such as tools or rags in the engine compartment.
Tools or other items left in the engine compartment could cause engine damage or a fi re
leading to an unexpected accident.
$9@&;&&%@&EJUJPOJOEC







6–38
Maintenance and Care
Owner Maintenance
Battery Maintenance
To get the best service from a battery:
 


 Keep it securely mounted.



 Keep the top clean and dry.



 Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


 Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


 If the vehicle will not be used for an
extended time, disconnect the battery
leads and charge the battery every six
weeks.
Inspecting Electrolyte Level
A low level of electrolyte fl uid will cause
the battery to discharge quickly.
Upper level
Lower level
Inspect the electrolyte level at least once
a week. If it is low, remove the caps and
add enough distilled water to bring the
level between the upper and lower level
(illustration).
Do not overfi ll.
Examine the specifi c gravity of the
electrolyte with a hydrometer, especially
during cold weather. If it is low, recharge
the battery.
Battery Recharging
NOTE
  Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
  To disconnect the battery, remove the
negative lead fi rst. Install it last when
connecting the battery.
  Be sure to remove the caps before
recharging the battery.
 (With i-stop system) Do not quick-charge the battery.




 If the battery quickly discharges
because, for example, the lights were
left on too long with the engine off,
slow-charge it as required by battery
size and charger capacity.
 


 If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it as
required by battery size and charger
capacity.
Battery Replacement
Contact an Authorised Mazda Dealer for a
battery replacement purchase.
$9@&;&&%@&EJUJPOJOEC







6–62
Maintenance and Care
Appearance Care
To help protect the fi nish from rust
and deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface when:
 


 The vehicle is washed without fi rst
rinsing off dirt and other foreign matter.
 


 The vehicle is washed with a rough, dry,
or dirty cloth.
 


 The vehicle is washed at a car wash that
uses brushes that are dirty or too stiff.
 


 Cleansers or wax containing abrasives
are used.
NOTE
  Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
  Scratches are more noticeable on
vehicles with darker paint fi nishes.
To minimize scratches on the vehicle's
paint fi nish:




 Rinse off any dirt or other foreign matter
using lukewarm or cold water before
washing.
 


 Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
 


 Rub gently when washing or drying the
vehicle.
 


 Take your vehicle only to a car wash
that keeps its brushes well maintained.
 


 Do not use abrasive cleansers or wax
that contain abrasives.
CAUTION
Do not use steel wool, abrasive cleaners,
or strong detergents containing highly
alkaline or caustic agents on chrome-
plated or anodised aluminium parts. This
may damage the protective coating; also,
cleaners and detergents may discolour or
deteriorate the paint.
Pay special attention to removing salt, dirt,
mud, and other foreign material from the
underside of the wings, and make sure the
drain holes in the lower edges of the doors
and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits
can damage the fi nish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Do not allow
soap to dry on the fi nish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
$9@&;&&%@&EJUJPOJOEC