warning lights MAZDA MODEL CX-3 2015 (in English) Owner's Guide

4–82
When Driving
ABS/TCS/DSC
Traction Control System
(TCS)
The Traction Control System (TCS)
enhances traction and safety by controlling
engine torque and braking. When the TCS
detects driving wheel slippage, it lowers
engine torque and operates the brakes to
prevent loss of traction.
This means that on a slick surface, the
engine adjusts automatically to provide
optimum power to the drive wheels,
limiting wheel spin and loss of traction.
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-37 .
WARNING
Do not rely on the Traction Control
System (TCS) as a substitute for safe
driving:
The Traction Control System (TCS)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning (reduced
tyre friction and road contact because
of water on the road surface). You can
still have an accident.
Use snow tyres or tyre chains and
drive at reduced speeds when roads are
covered with ice and/or snow:
Driving without proper traction devices
on snow and/or ice-covered roads
is dangerous. The Traction Control
System (TCS) alone cannot provide
adequate traction and you could still
have an accident.
NOTE
To turn off the TCS, press the TCS OFF
switch (page 4-83 ).
TCS/DSC Indicator Light
This indicator light stays on for a few
seconds when the ignition is switched
ON. If the TCS or DSC is operating, the
indicator light fl ashes.
If the light stays on, the TCS, DSC
or the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an expert
repairer, we recommend an Authorised
Mazda Repairer.
NOTE
  In addition to the indicator light
fl ashing, a slight labouring sound
will come from the engine. This
indicates that the TCS/DSC is
operating properly.
  On slippery surfaces, such as fresh
snow, it will be impossible to achieve
high rpm when the TCS is on.
$9@&;&&%@&EJUJPOJOEC







4–84
When Driving
ABS/TCS/DSC
Dynamic Stability
Control (DSC)
The Dynamic Stability Control (DSC)
automatically controls braking and engine
torque in conjunction with systems such
as ABS and TCS to help control side slip
when driving on slippery surfaces, or
during sudden or evasive manoeuvring,
enhancing vehicle safety.
Refer to ABS (page 4-81 ) and TCS (page
4-82 ).
DSC operation is possible at speeds
greater than 20 km/h (12 mph).
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-37 .
WARNING
Do not rely on the Dynamic Stability
Control as a substitute for safe driving:
The Dynamic Stability Control (DSC)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning (reduced
tyre friction and road contact because
of water on the road surface). You can
still have an accident.
CAUTION
  The DSC may not operate correctly
unless the following are observed:
 


 Use tyres of the correct size
specifi ed for your Mazda on all
four wheels.
 


 Use tyres of the same
manufacturer, brand and tread
pattern on all four wheels.
 


 Do not mix worn tyres. 

 The DSC may not operate correctly
when tyre chains are used or a
temporary spare tyre is installed
because the tyre diameter changes.
TCS/DSC Indicator Light
This indicator light stays on for a few
seconds when the ignition is switched
ON. If the TCS or DSC is operating, the
indicator light fl ashes.
If the light stays on, the TCS, DSC
or the brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an expert
repairer, we recommend an Authorised
Mazda Repairer.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–95
When Driving
4WD
4-Wheel Drive (4WD)
Operation
*
4WD provides excellent drivability on
snow-covered and ice-packed roads, sand
and mud, as well as on steep slopes and
other slippery surfaces.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page
4-37 .
WARNING
Never spin a wheel that is off the
ground:
Spinning a wheel that is off the ground
as a result of the vehicle being stuck
or in a ditch is dangerous. The drive
assembly could be seriously damaged
which could lead to an accident or
could even lead to overheating, oil
leakage, and a fi re.
4WD Driving
This vehicle has not been designed for the
purpose of off-road driving or rallies. Do
not attempt to drive over uneven or rocky
surfaces, or across rivers.
Although this vehicle is equipped with
4WD, acceleration, steering and braking
operations should be conducted in the
same manner as with a non-4WD vehicle,
with the emphasis placed on safe driving.
Tyres and Tyre Chains
The condition of the tyres plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to the
drive assembly, please note the following:
T y r e s
 




 When replacing tyres, always replace all
front and rear tyres at the same time.
 


 All tyres must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when equipping
snow or other types of winter tyres.
 


 Do not mix tread-worn tyres with
normal tyres.
 


(With tyre pressure monitoring
system)
  Inspect tyre infl ation pressures at the
specifi ed periods adjust to the specifi ed
pressures, and initialize the tyre pressure
monitoring system.
NOTE
Check the tyre infl ation pressure label
attached to driver's door frame for the
correct tyre infl ation pressure.




 Make sure to equip the vehicle with
genuine wheels of the specifi ed size,
on all wheels. With 4WD, the system is
calibrated for all four wheels being of
the same dimensions.
$9@&;&&%@&EJUJPOJOEC







4–97
When Driving
Power Steering
Power Steering
 












 Power steering is only operable when
the engine is running. If the engine is
off or if the power steering system is
inoperable, you can still steer, but it
requires more physical effort.
  If the steering feels stiffer than usual
during normal driving or the steering
vibrates, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
 


 The warning light notifi es the driver
of system abnormalities and operation
conditions.
  In addition, the buzzer may also activate
depending on the system abnormality or
operation condition.
  Refer to Warning Lights on page 4-37 .
 Refer to Power Steering Warning Buzzer
on page 7-54 .
CAUTION
Never hold the steering wheel to the
extreme left or right for more than
5 seconds with the engine running.
This could damage the power steering
system.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–101
When Driving
i-ACTIVSENSE
Adaptive Front Lighting System (AFS) *
The adaptive front lighting system (AFS) automatically adjusts the headlight beams to the
left or right in conjunction with the operation of the steering wheel after the headlights have
been turned on.
A system malfunction or operation conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page 4-36 .
NOTE
The Adaptive Front Lighting System (AFS) function can be switched to operable/
inoperable using the personalisation function.
Refer to Personalisation Features on page 9-13 .
$9@&;&&%@&EJUJPOJOEC







*Some models.4–102
When Driving
i-ACTIVSENSE
High Beam Control System (HBC) *
The High Beam Control System (HBC) determines the conditions in front of the vehicle
using the Forward Sensing Camera (FSC) while driving in darkness to automatically switch
the headlights between high and low beams.
Refer to Warning/Indicator Lights on page 4-36 .
While driving the vehicle at a speed of about 30 km/h (18 mph), the headlights are switched
to high beams when there are no vehicles ahead or approaching in the opposite direction.
The system switches the headlights to low beams when one of the following occurs:
 


 The system detects a vehicle or the headlights/lights of a vehicle approaching in the
opposite direction.
 


 The vehicle is driven on roads lined with streetlamps or on roads in well-lit cities and
towns.
 


 The vehicle is driven at less than about 20 km/h (12 mph).
Forward Sensing
Camera (FSC) The recognition distance of the
Forward Sensing Camera (FSC)
varies according to the
surrounding conditions.
The warning light fl ashes when the system has a malfunction.
Refer to Warning Lights on page 4-37 .
CAUTION
  Do not adjust the vehicle height, modify the headlight units, or remove the camera,
otherwise the system will not operate normally.
  Do not rely excessively on the High Beam Control System (HBC) and drive the
vehicle while paying suffi cient attention to safety. Switch the headlights between the
high beams and low beams manually if necessary.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–105
When Driving
i-ACTIVSENSE
Lane Departure Warning System (LDWS) *
The LDWS system notifi es the driver that the vehicle may be deviating from its lane.
The system detects the white or yellow lines on the traffi c lane using the forward sensing
camera and if it determines that the vehicle may be deviating from its lane, it notifi es the
driver using the active driving display (vehicles with active driving display), and by fl ashing
the LDWS warning light and activating the LDWS warning beep.
Use the LDWS when you drive the vehicle on roads with white or yellow lines.
Refer to Forward Sensing Camera on page 4-148 .
Use the LDWS when you drive the vehicle on roads with white or yellow lines.
Forward Sensing Camera (FSC)
LDWS warning light
The warning light illuminates when the system has a malfunction.
Refer to Warning Lights on page 4-37 .
$9@&;&&%@&EJUJPOJOEC







*Some models.4–111
When Driving
i-ACTIVSENSE
Blind Spot Monitoring (BSM) System *
The Blind Spot Monitoring (BSM) system is designed to assist the driver in checking the
area to the rear of the vehicle on both sides during lane changes by alerting the driver to the
presence of vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) system detects vehicles approaching from the rear while
travelling in the forward direction at a speed of 30 km/h (19 mph) or faster and turns on
the Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors depending
on the conditions. If the direction indicator lever is operated to signal a lane change in
the direction in which the Blind Spot Monitoring (BSM) warning light is illuminated,
the system warns the driver of a vehicle in the detection area by fl ashing the Blind Spot
Monitoring (BSM) warning light and activating a beep sound.
The detection area on this system covers the driving lanes on both sides of the vehicle and
from the rear part of the front doors to about 50 m (164 ft) behind the vehicle.
Detection areas Your vehicle
WARNING
Always check the surrounding area visually before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not fl ash or it might be delayed even
though a vehicle is in an adjacent driving lane. Always make it your responsibility as a
driver to check the rear.
$9@&;&&%@&EJUJPOJOEC







4–112
When Driving
i-ACTIVSENSE
NOTE
  The Blind Spot Monitoring (BSM) system will operate when all of the following
conditions are met:
 


 The ignition is switched ON.



 The Blind Spot Monitoring (BSM) switch is pressed and the Blind Spot Monitoring
(BSM) OFF indicator light in the instrument cluster is turned off.
 


 The vehicle speed is about 30 km/h (19 mph) or faster. 

 The Blind Spot Monitoring (BSM) system will not operate under the following
circumstances.
 


 The vehicle speed falls below about 25 km/h (15 mph) even though the Blind Spot
Monitoring (BSM) OFF indicator light is turned off.
 


 The shift lever (manual transaxle)/selector lever (automatic transaxle) is shifted to
reverse (R) and the vehicle is reversing.
 
 In the following cases, the Blind Spot Monitoring (BSM) OFF indicator light turns
on and operation of the system is stopped. If the Blind Spot Monitoring (BSM) OFF
indicator light remains illuminated, have the vehicle inspected at an Authorised Mazda
Dealer as soon as possible.
 


 Some problem with the system including the Blind Spot Monitoring (BSM) warning
lights is detected.
 


 A large deviation in the installation position of a radar sensor (rear) on the vehicle
has occurred.
 


 There is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear). Remove any snow, ice or mud on the rear bumper.
 


 Driving on snow-covered roads for long periods.



 The temperature near the radar sensors (rear) becomes extremely hot due to driving
for long periods on slopes during the summer.
 


 The battery voltage has decreased. 

 Under the following conditions, the radar sensors (rear) cannot detect target objects or
it may be diffi cult to detect them.




 A vehicle is in the detection area at the rear in an adjacent driving lane but it does
not approach. The Blind Spot Monitoring (BSM) system determines the condition
based on radar detection data.
 


 A vehicle is travelling alongside your vehicle at nearly the same speed for an
extended period of time.
 


 Vehicles approaching in the opposite direction.



 A vehicle in an adjacent driving lane is attempting to pass your vehicle.



 A vehicle is in an adjacent lane on a road with extremely wide driving lanes. The
detection area of the radar sensors (rear) is set at the road width of expressways.
$9@&;&&%@&EJUJPOJOEC







4–113
When Driving
i-ACTIVSENSE
NOTE
  In the following cases, the activation of the Blind Spot Monitoring (BSM) warning
lights and the warning beep may not occur or they may be delayed.
 


 A vehicle makes a lane change from a driving lane two lanes over to an adjacent
lane.
 


 Driving on steep slopes.



 Crossing the summit of a hill or mountain pass.



 The turning radius is small (making a sharp curve, turning at intersections).



 When there is a difference in the height between your driving lane and the adjacent
lane.
 


 Directly after pressing the Blind Spot Monitoring (BSM) switch and the system
becomes operable.
 
 If the road width is extremely narrow, vehicles two lanes over may be detected.
The detection area of the radar sensors (rear) is set according to the road width of
expressways.
  The Blind Spot Monitoring (BSM) warning lights may turn on in reaction to stationary
objects on the road or the roadside such as guardrails, tunnels, sidewalls, and parked
vehicles.
Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.
The walls at the entrance and exits of tunnels,
turnouts.
  A Blind Spot Monitoring (BSM) warning light may fl ash or the warning beep may be
activated several times when making a turn at a city intersection.
  Turn off the Blind Spot Monitoring (BSM) system while pulling a trailer or while an
accessory such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the
radar’s radio waves will be blocked causing the system to not operate normally.
$9@&;&&%@&EJUJPOJOEC