warning light MAZDA MODEL CX-3 2017 Owners Manual (in English)

4–126
When Driving
Tire Pressure Monitoring System
*Some models.
Tire Pressure Monitoring System *
The Tire Pressure Monitoring System (TPMS) monitors the air pressure of all four tires. If
the air pressure of one or more tires is too low, the system warns the driver by indicating the
tire pressure monitoring system warning light in the instrument cluster and operating a beep
sound. The system monitors the tire pressures indirectly using the data sent from the ABS
wheel speed sensors.
To allow the system to operate correctly, the system needs to be initialized with the speci¿ ed
tire pressure (value on the tire pressure label). Follow the procedure and perform the
initialization.
Refer to Tire Pressure Monitoring System Initialization on page 4-129 .
The warning light À ashes when the system has a malfunction.
Refer to Warning Lights on page 4-25 .


ABS wheel speed sensor
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–128
When Driving
Tire Pressure Monitoring System
N O T E
Because this system detects slight changes in tire conditions, the timing of the warning may
be faster or slower in the following cases:
 


y The size, manufacturer, or the type of tires is different from the speci¿ cation.



y The size, manufacturer, or the type of a tire is different from the others, or the level of tire
wear is excessively different between them.
 


y A run-À at tire, studless tire, snow tire, or tire chains are used.



y An emergency tire is used (The tire pressure monitoring system warning light may À ash
and then continue illuminating).
 


y A tire is repaired using the emergency À at tire repair kit.



y The tire pressure is excessively higher than the speci¿ ed pressure, or the tire pressure is
suddenly lowered for some reason such as a tire burst during driving.
 


y The vehicle speed is lower than about 15 km/h (9.3 mph) (including when the vehicle is
stopped), or the drive period is shorter than 5 minutes.
 


y The vehicle is driven on an extremely rough road or a slippery, icy road.



y Hard steering and rapid acceleration/deceleration are repeated such as during aggressive
driving on a winding road.
 


y Load on the vehicle is applied to a tire such as by loading heavy luggage to one side of
the vehicle.
 


y System initialization has not been implemented with the speci¿ ed tire pressure.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–129
When Driving
Tire Pressure Monitoring System
Tire Pressure Monitoring System
Initialization
In the following cases, system
initialization must be performed so that the
system operates normally.
 


y A tire pressure is adjusted.



y Tire rotation is performed.



y A tire or wheel is replaced.



y The battery is replaced or completely
drained.
 


y The tire pressure monitoring system
warning light is illuminated.


Initialization method

1. Park the car in a safe place and ¿ rmly
apply the parking brake.
2. Let the tires cool, then adjust the tire
pressure of all four (4) tires to the
speci¿ ed pressure indicated on the tire
pressure label located on the driver's
door frame (door open).
Refer to Tires on page 9-8 .
3. Switch the ignition ON.
4. Press and hold the tire pressure
monitoring system set switch and
verify that the tire pressure monitoring
system warning light in the instrument
cluster À ashes twice and a beep sound
is heard once.


CAUTION
If the system initialization is performed
without adjusting the tire pressure,
the system cannot detect the normal
tire pressure and it may not illuminate
the tire pressure monitoring system
warning light even if a tire pressure is
low, or it may illuminate the light even
if the pressures are normal.
Adjust the tire pressure on all four
tires and initialize the system when
the warning light is turned on. If the
warning light turns on for a reason
other than a fl at tire, the tire pressure
of all four tires may have decreased
naturally.
The system initialization will not be
performed if the switch is pressed while
the vehicle is being driven.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–6
Interior Features
Climate Control System
Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
N O T E
(Type A)
When the mode is set to
or with the
fan control dial in a position other than 0
and the temperature control dial in the
maximum cold position, the air intake
selector switches to the recirculated air
position and the A/C turns on
automatically.
If A/C is not desired, press the A/C switch
to turn it off.

Fan control dial
This dial allows variable fan speeds.
0—Fan off
1—Low speed
2—Medium low speed
3—Medium high speed
4—High speed
Mode selector dial
Turn the mode selector dial to select
airÀ ow mode (page 5-4 ).
N O T E




y The mode selector dial can be set at the
intermediate positions (
) between
each mode. Set the dial to an
intermediate position if you want to split
the airÀ ow between the two modes.




y For example, when the mode selector
dial is at the
position between the
and
positions, airÀ ow from the À oor
vent is less than that of the
position.
A/C switch
Press the A/C switch to turn the air
conditioner on. The indicator light on the
switch will illuminate when the fan control
dial is set at position 1, 2, 3, or 4.
Press the switch once again to turn the air
conditioner off.
N O T E
The air conditioner may not function when
the outside temperature approaches 0 °C
(32 °F).

Air intake selector (Type A)
This switch controls the source of air
entering the vehicle.
Press the air intake selector switch to
alternate between the outside air and
recirculated air positions.
Recirculated air position (
)
Outside air is shut off. Air within the
vehicle is recirculated.
Outside air position (
)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windshield defrosting.
WARNING
Do not use the recirculated air position
in cold or rainy weather:
Using the recirculated air position in
cold or rainy weather is dangerous as it
will cause the windows to fog up. Your
vision will be hampered, which could
lead to a serious accident.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–8
Interior Features
Climate Control System
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.

CAUTION
If the air conditioner is used while
driving up long hills or in heavy
traffi c, monitor the engine coolant
temperature warning light to see if it is
illuminated or fl ashing (page 4-24 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air-
conditioning off (page 7-22 ).

N O T E




y When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then set the fan control dial to
position 4.
 


y If warmer air is desired at À oor level,
set the mode selector dial at the

position and adjust the temperature
control dial to maintain maximum
comfort.
 


y The air to the À oor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).

Ventilation
1. Set the mode selector dial to the
position.
2. (Type A)
Set the air intake selector to the outside
air position.
(Type B)
Set the air intake selector to the

position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–12
Interior Features
Climate Control System
Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traf¿ c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windshield defrosting.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.

Operation of Automatic Air-
Conditioning
1. Set the mode selector dial to the AUTO
position.
2. Set the air intake selector to the outside
air position (indicator light turned off).
N O T E
If the recirculated air position is used
for long periods in cold weather or high
humidity, the windshield may fog up more
easily.

3. Set the fan control dial to the AUTO
position.
4. Press the A/C switch to operate the air-
conditioning (turn indicator light on).
5. Set the temperature control dial to the
desired position.
6. To turn off the system, set the fan
control dial to the 0 position.

N O T E
 


y Setting the temperature to maximum
hot or cold will not provide the desired
temperature at a faster rate.
 


y When selecting heat, the system will
restrict airÀ ow until it has warmed to
prevent cold air from blowing out of the
vents.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–13
Interior Features
Climate Control System
Windshield Defrosting and
Defogging
Set the mode selector dial to the
position and turn the fan control dial to the
desired speed.
In this position, the outside air position
is automatically selected, and when the
fan control dial is ON, the air conditioner
automatically turns on. The air conditioner
will directly dehumidify the air to the
front windshield and side windows (page
5-4 ). AirÀ ow amount will be increased.
WARNING
Set the temperature control to the hot
or warm position when defogging
(
position):
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windshield to fog up.
Your vision will be hampered, which
could lead to a serious accident.

N O T E
Use the temperature control dial to
increase the air À ow temperature and
defog the windshield more quickly.

Sunlight/Temperature Sensor
The climate control system measures
inside and outside temperatures, and
sunlight. It then sets temperatures inside
the passenger compartment accordingly.
CAUTION
Do not obstruct either sensor,
otherwise the climate control system
will not operate properly.



Sunlight sensor



Interior temperature sensor
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–55
Interior Features
Audio System
Applications
N O T E
Depending on the grade and speci¿ cation,
the screen display may differ.

Select the icon on the home screen to
display the Applications screen. The
following information can be veri¿ ed.

Top screen Item
Function
HD Radio™
Traf¿ c Map —
—
Fuel
Economy
Monitor Fuel
Consumption
Settings Refer to Fuel
Economy Monitor
on page 4-62 .
Maintenance Scheduled
Maintenance
Tire Rotation
Oil Change Refer to
Maintenance
Monitor (Type B
audio) on page
6-20 .
Warning
Guidance Warnings
currently active
can be veri¿ ed. Refer to If a
Warning Light
Turns On or
Flashes on page
7-27 .

Audio Control Switch
Operation
Without Bluetooth ® Hands-Free



With Bluetooth
® Hands-Free



%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–133
Interior Features
Interior Equipment
CAUTION
 


¾ To prevent accessory socket damage or
electrical failure, pay attention to the
following:
 


¾ Do not use accessories that require
more than 120 W (DC 12 V, 10 A).
 


¾ Do not use accessories that are not
genuine Mazda accessories or the
equivalent.
 


¾ Close the cover when the accessory
socket is not in use to prevent foreign
objects and liquids from getting into
the accessory socket.
 


¾ Correctly insert the plug into the
accessory socket.
 


¾ Do not insert the cigarette lighter into
the accessory socket.
 


¾ Noise may occur on the audio playback
depending on the device connected to
the accessory socket.
 


¾ Depending on the device connected
to the accessory socket, the vehicle's
electrical system may be aff ected,
which could cause the warning light to
illuminate. Disconnect the connected
device and make sure that the problem
is resolved. If the problem is resolved,
disconnect the device from the socket
and switch the ignition off . If the
problem is not resolved, consult an
Authorized Mazda Dealer.

N O T E
To prevent discharging of the battery, do
not use the socket for long periods with the
engine off or idling.

Cup Holder
WARNING
Never use a cup holder to hold hot
liquids while the vehicle is moving:
Using a cup holder to hold hot
liquids while the vehicle is moving is
dangerous. If the contents spill, you
could be scalded.

Do not put anything other than cups or
drink cans in cup holders:
Putting objects other than cups
or drink cans in a cup holder is
dangerous.
During sudden braking or
maneuvering, occupants could be
hit and injured, or objects could be
thrown around the vehicle, causing
interference with the driver and the
possibility of an accident. Only use a
cup holder for cups or drink cans.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

5–134
Interior Features
Interior Equipment
Bottle Holder
Bottle holders are on the inside of the
doors.

Bottle holder
CAUTION
Do not use the bottle holders for
containers without caps. The contents
may spill when the door is opened or
closed.

Storage Compartments
WARNING
Keep storage boxes closed when
driving:
Driving with the storage boxes open is
dangerous. To reduce the possibility of
injury in an accident or a sudden stop,
keep the storage boxes closed when
driving.

Do not put articles in storage spaces
with no lid:
Putting articles in storage spaces with
no lid is dangerous as they could be
thrown around the cabin if the vehicle
is suddenly accelerated and cause
injury depending on how the article is
stored.

CAUTION
Do not leave lighters or eyeglasses
in the storage boxes while parked
under the sun. A lighter could explode
or the plastic material in eyeglasses
could deform and crack from high
temperature.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD