warning light MAZDA MODEL CX-3 2017 (in English) Repair Manual

4–65
When Driving
i-ACTIV AWD
i-ACTIV AWD Operation
AWD provides excellent drivability on
snow-covered and ice-packed roads, sand
and mud, as well as on steep slopes and
other slippery surfaces.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Warning Lights on page 4-25 .
WARNING
Never spin a wheel that is off the
ground:
Spinning a wheel that is off the ground
as a result of the vehicle being stuck
or in a ditch is dangerous. The drive
assembly could be seriously damaged
which could lead to an accident or
could even lead to overheating, oil
leakage, and a fi re.

AWD Driving
This vehicle has not been designed for the
purpose of off-road driving or rallies. Do
not attempt to drive over uneven or rocky
surfaces, or across rivers.
Although this vehicle is equipped with
AWD, acceleration, steering and braking
operations should be conducted in the
same manner as with a non-AWD vehicle,
with the emphasis placed on safe driving.
Tires and Tire Chains
The condition of the tires plays a large
role in the performance of the vehicle.
Moreover, to prevent adverse effects to the
drive assembly, please note the following:
T i r e s
 




y When replacing tires, always replace all
front and rear tires at the same time.
 


y All tires must be of the same size,
manufacture, brand and tread pattern.
Pay particular attention when equipping
snow or other types of winter tires.
 


y Do not mix tread-worn tires with normal
tires.
 


y Inspect tire inÀ ation pressures at the
speci¿ ed periods adjust to the speci¿ ed
pressures, and initialize the tire pressure
monitoring system.
  Refer to Tire Pressure Monitoring
System Initialization on page 4-129 .

N O T E
Check the tire inÀ ation pressure label
attached to driver's door frame for the
correct tire inÀ ation pressure.




y Make sure to equip the vehicle with
genuine wheels of the speci¿ ed size, on
all wheels. With AWD, the system is
calibrated for all four wheels being of
the same dimensions.

Tire chains
 




y Install tire chains to the front tires.



y Do not use tire chains on the rear
wheels.
 


y Do not drive the vehicle faster than
30 km/h (19 mph) with the tire chains
installed.
 


y Do not drive the vehicle with tire chains
on road conditions other than snow or
ice.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–67
When Driving
Power Steering
Power Steering
 












y Power steering is only operable when
the engine is running. If the engine is
off or if the power steering system is
inoperable, you can still steer, but it
requires more physical effort.
  If the steering feels stiffer than usual
during normal driving or the steering
vibrates, consult an Authorized Mazda
Dealer.
 


y The warning light noti¿ es the driver
of system abnormalities and operation
conditions.
  In addition, the buzzer may also activate
depending on the system abnormality or
operation condition.
  Refer to Warning Lights on page
4-25 .
  Refer to Power Steering Warning Buzzer
on page 7-42 .

CAUTION
Never hold the steering wheel to the
extreme left or right for more than 5
seconds with the engine running. This
could damage the power steering
system.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–68
When Driving
i-ACTIVSENSE
*Some models.
i-ACTIVSENSE *
i-ACTIVSENSE is a collective term covering a series of advanced safety and driver support
systems which make use of a Forward Sensing Camera (FSC) and radar sensors. These
systems consist of active safety and pre-crash safety systems.
These systems are designed to assist the driver in safer driving by reducing the load on the
driver and helping to avert collisions or reduce their severity. However, because each system
has its limitations, always drive carefully and do not rely solely on the systems.
Active Safety Technology
Active Safety Technology supports safer driving by helping the driver to recognize potential
hazards and avert accidents.
Driver awareness support systems
Nighttime visibility
Adaptive Front Lighting System (AFS) .............................................................................. 4-70
High Beam Control System (HBC) .................................................................................... 4-71
Left/right side and rear side detection
Lane Departure Warning System (LDWS) ......................................................................... 4-74
Blind Spot Monitoring (BSM) System ............................................................................... 4-80
Inter-vehicle distance recognition
Distance Recognition Support System (DRSS) .................................................................. 4-86
Rear obstruction detection when leaving a parking space
Rear Cross Traf¿ c Alert (RCTA) ........................................................................................ 4-89
Driver support system
Inter-vehicle distance
Mazda Radar Cruise Control (MRCC) ............................................................................... 4-92
Pre-Crash Safety Technology
Pre-crash safety technology is designed to assist the driver in averting collisions or reduce
their severity in situations where they cannot be avoided.
Collision damage reduction in low vehicle speed range
Forward driving
Smart City Brake Support (SCBS) ................................................................................... 4-103
Collision damage reduction in medium/high speed range
Smart Brake Support (SBS) .............................................................................................. 4-108
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–70
When Driving
i-ACTIVSENSE
*Some models.
Adaptive Front Lighting System (AFS) *
The adaptive front lighting system (AFS) automatically adjusts the headlight beams to the
left or right in conjunction with the operation of the steering wheel after the headlights have
been turned on and the vehicle speed is about 2 km/h (2 mph) or higher.
A system malfunction or operation conditions are indicated by a warning.
Refer to Warning/Indicator Lights on page 4-24 .
N O T E
The Adaptive Front Lighting System (AFS) function can be switched to operable/inoperable
using the personalization function.
Refer to Personalization Features on page 9-10 .

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–71
When Driving
i-ACTIVSENSE
*Some models.
High Beam Control System (HBC) *
The High Beam Control System (HBC) determines the conditions in front of the vehicle
using the Forward Sensing Camera (FSC) while driving in darkness to automatically switch
the headlights between high and low beams.
Refer to Warning/Indicator Lights on page 4-24 .
While driving the vehicle at a speed of about 30 km/h (19 mph), the headlights are switched
to high beams when there are no vehicles ahead or approaching in the opposite direction.
The system switches the headlights to low beams when one of the following occurs:
 


y The system detects a vehicle or the headlights/lights of a vehicle approaching in the
opposite direction.
 


y The vehicle is driven on roads lined with streetlamps or on roads in well-lit cities and
towns.
 


y The vehicle is driven at less than about 20 km/h (12 mph).

Forward Sensing
Camera (FSC) The recognition distance of the
Forward Sensing Camera (FSC)
varies according to the
surrounding conditions.

The warning light À ashes when the system has a malfunction.
Refer to Warning Lights on page 4-25 .
CAUTION
 


¾ Do not adjust the vehicle height, modify the headlight units, or remove the camera,
otherwise the system will not operate normally.
 


¾ Do not rely excessively on the High Beam Control System (HBC) and drive the vehicle while
paying suffi cient attention to safety. Switch the headlights between the high beams and
low beams manually if necessary.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–74
When Driving
i-ACTIVSENSE
*Some models.
Lane Departure Warning System (LDWS) *
The LDWS system noti¿ es the driver that the vehicle may be deviating from its lane.
The system detects the white or yellow lines on the traf¿ c lane using the Forward Sensing
Camera (FSC) and if it determines that the vehicle may be deviating from its lane, it noti¿ es
the driver using the active driving display (vehicles with active driving display), and by
À ashing the LDWS warning light and activating the LDWS warning beep.
Use the LDWS when you drive the vehicle on roads with white or yellow lines.
Refer to Forward Sensing Camera on page 4-111 .


Forward Sensing Camera (FSC)
LDWS warning light

The warning light illuminates when the system has a malfunction.
Refer to Warning Lights on page 4-25 .
WARNING
Do not use the LDWS under the following conditions:
The system may not operate adequately according to the actual driving conditions,
resulting in an accident.
 


¾ Driving on roads with tight curves.



¾ Driving under bad weather conditions (rain, fog, and snow).

The functions of the LDWS have limitations:
Always stay on course using the steering wheel and drive with care. The system is not
designed to compensate for a driver’s lack of caution and if you rely too much on the
LDWS it could lead to an accident. The driver is responsible for assuring lane changes and
other maneuvers. Always pay attention to the direction in which the vehicle is traveling
and the vehicle’s surroundings.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–76
When Driving
i-ACTIVSENSE
N O T E
 


y If your vehicle deviates from its traf¿ c lane, the LDWS operates (warning sound and
indicator light). Steer the vehicle adequately to drive the vehicle to the center of the lane.
 


y When the turn signal lever is operated for a lane change, the LDWS warning is
automatically canceled. The LDWS warning becomes operable when the turn signal lever
is returned and the system detects the white or yellow lines.
 


y If the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white or yellow line, the system determines that the driver is
making a lane change and the LDWS warning is automatically canceled.
 


y The LDWS may not operate during the period immediately after the vehicle has deviated
from its lane and the LDWS has operated, or the vehicle deviates from its lane repeatedly
within a short period of time.
 


y The LDWS does not operate if it does not detect the white or yellow lines of the traf¿ c
lane.
 


y Under the following conditions, the LDWS may not be able to detect white or yellow lines
correctly and the LDWS may not operate correctly.
 


y If an object placed on the dashboard is reÀ ected in the windshield and picked up by the
camera.
 


y Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is inclined.
 


y The tire pressures are not adjusted to the speci¿ ed pressure.



y When the vehicle is driven on the entry and exit to or from the rest area or tollgate of a
highway.
 


y The white or yellow lines are less visible because of dirt or paint À aking.



y The vehicle ahead is running near a white or yellow line and the line is less visible.



y A white or yellow line is less visible because of bad weather (rain, fog, or snow).



y The vehicle is driven on a temporary lane or section with a closed lane due to
construction.
 


y A misleading line is picked up on the road such as a temporary line for construction,
or because of shade, lingering snow, or grooves ¿ lled with water.




y The surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
 


y The illumination of the headlights is weakened because of dirt or the optical axis is
deviated.
 


y The windshield is dirty or foggy.



y Back-light is reÀ ecting from the road surface.



y The road surface is wet and shiny after rain, or there are puddles on the road.



y The shade of a guardrail parallel to a white or yellow line is on the road.
y The width of a lane is excessively narrow or wide.



y The road is excessively uneven.



y The vehicle is shaken after hitting a road bump.



y There are two or more adjacent white or yellow lines.



y There are various road markings or lane markings of various shapes near an
intersection.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–78
When Driving
i-ACTIVSENSE
N O T E
 


y The LDWS does not operate until the
system detects a white or yellow line on
either the left or right.
 


y When the system detects a white or
yellow line on one side only, the system
will activate the warning only when the
vehicle deviates on the side where the
white or yellow line is being detected.
 


y The distance and warning sensitivity
(likelihood of a warning) which the
system uses to determine the possibility
of a lane departure can be changed.
  Refer to Personalization Features on
page 9-10 .

Auto cancel
In the following cases, the LDWS cancels
automatically and the LDWS warning
light in the instrument cluster turns on.
 


y The temperature inside the camera is
high or low.
 


y The windshield around the camera is
foggy.
 


y The windshield around the camera is
blocked by an obstruction, causing poor
forward visibility.

For vehicles equipped with the active
driving display, the lane (border lines) is
indicated in the display. The LDWS is
enabled automatically when the operation
conditions are met, and the LDWS
warning light turns off.
Auto cancel warning
When the following operations are
performed, the LDWS determines that
the driver intends to make a lane change
and the LDWS warning is canceled
automatically. The LDWS is enabled
automatically after the driver performs the
operation.
 


y The steering wheel is operated abruptly.



y The brake pedal is depressed abruptly.



y The accelerator pedal is depressed
abruptly.
 


y The turn signal lever is operated (after
the turn signal lever is returned, the
LDWS may not operate for about 3
seconds which is the period of time
required to make a lane correction).

N O T E
After about 60 seconds have elapsed with
the turn signal lever left operating, the
LDWS warning may operate if the vehicle
is close to a white or yellow line.

Canceling the System
Press the LDWS switch to cancel the
LDWS. The LDWS OFF indicator light
turns on.
For vehicles with the active driving
display, the driving lane indication in the
active driving display is not indicated
when the LDWS is cancelled.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–79
When Driving
i-ACTIVSENSE
LDWS Warning
If the system determines that there is the
possibility of a lane departure, the LDWS
warning beep activates and the LDWS
warning light À ashes. Operate the steering
wheel appropriately and steer the vehicle
to the center of the lane.
For vehicles equipped with the active
driving display, if there is the possibility of
a lane departure, the system indicates the
direction it determines that the vehicle is
deviating in the active driving display.
Indication on display



N O T E
 


y If the LDWS warning sound is set to
rumble *1 , the sound will be heard from
the vehicle speaker on the side which
the system determined the vehicle may
be deviating from its lane.
 


y It may be dif¿ cult to hear the LDWS
warning beep depending on the
surrounding conditions such as outside
noise.
 


y The volume of the LDWS warning sound
can be changed.
  Refer to Personalization Features on
page 9-10 .
 


y The type of warning sound (rumble *1 /
beep) on the LDWS can be changed.
  Refer to Personalization Features on
page 9-10 .

*1 A rumble strip is a series of grooves in
the road pavement surface positioned at
speci¿ c intervals, and when the vehicle
passes over it a vibration and rumble
sound is produced which alerts the
driver that the vehicle is departing from
the lane.
  The rumble sound is a reproduction of
the sound which occurs when a vehicle
passes over a rumble strip.
 

Rumble
Groove

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

4–80
When Driving
i-ACTIVSENSE
*Some models.
Blind Spot Monitoring (BSM) *
The Blind Spot Monitoring (BSM) is designed to assist the driver in checking the area to the
rear of the vehicle on both sides during lane changes by alerting the driver to the presence of
vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) detects vehicles approaching from the rear while
traveling in the forward direction at a speed of 10 km/h (6.3 mph) or faster and turns on the
Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors depending on
the conditions. If the turn signal lever is operated to signal a lane change in the direction
in which the Blind Spot Monitoring (BSM) warning light is illuminated, the system warns
the driver of a vehicle in the detection area by À ashing the Blind Spot Monitoring (BSM)
warning light and activating a beep sound.
The detection area on this system covers the driving lanes on both sides of the vehicle and
from the rear part of the front doors to about 50 m (164 ft) behind the vehicle.

Detection areas Your vehicle

WARNING
Always check the surrounding area visually before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not fl ash or it might be delayed even
though a vehicle is in an adjacent driving lane. Always make it your responsibility as a
driver to check the rear.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD