MAZDA MODEL CX-7 2008 Owners Manual (in English)

11
Before Use
Ifnecessary
Rear View
Monitor
MEMO
'<C)%FSSO4EKI8LYVWHE]1EVGL41

12
RoutingAddress
Book
Getting started
Activation
Insert the map disc into the unit to start the Mobile Navigation System.
Note
l
The map disc cannot be inserted or ejected while the ignition switch is in the OFF position.
l Remember that the battery can run down if the ignition switch is kept in the ACC or ON
position for a long time while the engine not running.
nMap Disc
l Refer to “Handling and Care of Map Discs” to know how to handle a map
disc ( page 60).
1
Remove the cover.
(Mazda CX-9 only)Note
lThe main unit is located on the right side of the
cargo sub-compartment under the trunk board.
(Mazda CX-9)
The main unit is located under the front passenger
seat. (Mazda CX-7)
l Condensation may form on the optical lens or the
map disc inside the unit when the temperature in
the vehicle increases in a short time such as when
heating the car on a cold day. This condensation
may cause malfunctions. If so, unload the map disc
and do not operate the unit for approximately 1
hour. Wipe the condensation off the map disc with a
soft cloth.
If the unit does not operate correctly after 1 hour,
consult an Authorized Mazda Dealer.
Note
lWhen the ignition switch is in the ACC or ON
position, the screen changes as follows to activate
the navigation system.
l The screen (audio or navigation) that was displayed
prior to the engine being turned off is displayed.
Before the navigation screen is displayed, the
CAUTION screen will be displayed.
2
Insert the map disc
with the printed side
facing up.
Cautions
Cover
(CAUTION) screen
'<C)%FSSO4EKI8LYVWHE]1EVGL41

13
Getting started
Ifnecessary
Rear View
Monitor
lThe Current Position screen appears.
Note
lYou can select the language by selecting the on-screen button. You can also
change the selected language using Language Selection. ( page 22)
l The CAUTION screen remains on the display unless you select the on-screen
button.
(Mazda CX-9)
If the mobile telephone is programmed to the hands-free unit for use with the Bluetooth
hands-free telephone, the Bluetooth hands-free information is displayed on the screen
momentarily. While this information is displayed, the on-screen button cannot be
selected. Select the on-screen button after the display is cleared.
Select the on-screen button lightly with your finger.
Colors for unavailable buttons will be pale.
3
Read the CAUTION
carefully, and select
the on-screen
button.
Removing the Map Disc
1
With the ignition switch in the ACC position, remove the cover.
2
Press (EJECT).
On-screen Buttons
Most functions are inhibited while the
vehicle is in motion.
Please read the handbook for operation
instructions.
Always obey traffic regulations.
Caution
Mazda CX-9
Cover
Do not get your hand or fingers caught in
moving parts or in the disc slot. This can
cause injuries. Children are inquisitive, try
to install or remove the map disc without
infants looking on.
Caution
Screw Screw
Bracket
Mazda CX-7
'<C)%FSSO4EKI8LYVWHE]1EVGL41

14
RoutingAddress
Book
Getting started
Set Clock
The current time is set using this function. Since time notification is \
provided by a GPS
satellite.
Before Steps select MENU
Open the [SET CLOCK] screen
Select if you prefer 24-hour display;
for 12-hour display.
Select to move the setting ahead by one hour,
and similarly, select to move it back by one
hour.
How to exit .
Note
Minutes and seconds are adjusted by the GPS, however, it is necessary to
adjust hours under the following conditions:
l
Driving across different time zones
l Daylight saving time start and end
'<C)%FSSO4EKI8LYVWHE]1EVGL41

15
Getting started
Ifnecessary
Rear View
Monitor
Navigation Set Up
lYou can alter the map display conditions, the route guidance conditions and show the
system information.
nStop your vehicle before the following operations. Do not change the settings and destination locations while driving. Minimize the time
spent viewing the monitor screen and listening to the voice guidance while driving.
Operating the system will distract the driver from looking ahead of the vehicle and may
cause an accident.
Always stop the vehicle in a safe location and put the parking brake on before operating
the system.
Before Stepsselect
Warning
MENU
Open
[NAVIGATION SET UP] ( page 20)
( page 22)
( page 16)
( page 24)
( page 18)
( page 23)
'<C)%FSSO4EKI8LYVWHE]1EVGL41

16
RoutingAddress
Book
Getting started
Navigation Set Up
You can change the language of the menu and the voice guidance.
Before Steps
select
select

Language
MENU
Open the [LANGUAGE] screen
Select your preferred language from the list.
'<C)%FSSO4EKI8LYVWHE]1EVGL41

17
Getting started
Ifnecessary
Rear View
Monitor
MEMO
'<C)%FSSO4EKI8LYVWHE]1EVGL41

18
RoutingAddress
Book
Getting started
Navigation Set Up
This function allows you to correct any error in the position or direction of your vehicle display.
Before Steps select
Adjusting Current Position and Direction
select
Open the [Calibrate Position] screen
Move to the correct position and select .
Use
or to adjust the direction in which you are
heading, and select .
Distance
This function automatically corrects any error in the display of the current
position that might occur after tire replacement.
select
You will have to drive about 6 miles (10 km) before distance correction is complete.
Map Vers
The map an
select
Map and so
Calibration
MENU
'<C)%FSSO4EKI8LYVWHE]1EVGL41

19
Getting started
Ifnecessary
Rear View
Monitor
select
.
h you are
urrent
omplete.
Map Version
The map and software version numbers can be confirmed using this function.
select
Map and software versions are now displayed.
'<C)%FSSO4EKI8LYVWHE]1EVGL41

20
RoutingAddress
Book
Getting started
Navigation Set Up
Before Steps
select
select

User Setting
MENU
Open the
[USER SETTINGS]
screen
nMap Color
Select a screen color from to options.
nMap Mode
lAuto : The display will automatically switch between Day
and Night illumination mode when the headlights are
turned off and on respectively.
lDay :The display will be presented in Day illumination mode
regardless of whether the headlights are on or off.
lNight : The display will be presented in Night illumination mode regardless of whether the headlights are on or off.
nDistance
Select the distance unit from or .
nAverage Speed
Set the average speed for each road to be driven.
(This function sets the standard speed (average vehicle speed
for each route) used for calculating the estimated arrival time
when calculating the route time.)
: Average speed setting:Changes back to default
nRoad Restriction Warnings
The display of warnings during route guidance when passing
through areas with traffic restrictions can be turned on or off.
'<C)%FSSO4EKI8LYVWHE]1EVGL41