height MAZDA MODEL CX-9 2017 (in English) User Guide

Page 286 of 612

4–138
When Driving
i-ACTIVSENSE
NOTE
 


 In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
 


 The height of the vehicle ahead is low.



 You drive your vehicle at the same speed as the vehicle ahead.



 Headlights are not turned on during the night or when going through a tunnel. 



 In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
 


 When driving next to walls with no patterning (including fences and longitudinally
striped walls).
 


 The taillights of the vehicle ahead are turned off.



 A vehicle is outside the illumination range of the headlights.



 The vehicle is making a sharp turn, or ascending or descending a steep slope.



 Entering or exiting a tunnel.



 Heavy luggage is loaded causing the vehicle to tilt.



 Strong light is shone at the front of the vehicle (back light or high-beam light from on-
coming vehicles).
 


 There are many light emitters on the vehicle ahead.



 When the vehicle ahead is not equipped with taillights or the taillights are turned off at
nighttime.
  The vehicle ahead has a special shape. For example, a vehicle towing a trailer house
or a boat, or a vehicle carrier carrying a vehicle with its front pointed rearward.


CX-9_8FS7-EA-16K_Edition2.indb 138CX-9_8FS7-EA-16K_Edition2.indb 1382016/12/15 18:34:362016/12/15 18:34:36

Page 289 of 612

4–141
When Driving
i-ACTIVSENSE
NOTE
 


 Under the following conditions, the radar sensor (front) may not be able to detect
vehicles ahead or obstructions correctly and each system may not operate normally.
 


 The rear surface of a vehicle ahead does not refl ect radio waves effectively, such as
an unloaded trailer or an automobile with a loading platform covered by a soft top,
vehicles with a hard plastic tailgate, and round-shaped vehicles.
 


 Vehicles ahead with low vehicle height and thus less area for refl ecting radio waves.



 Visibility is reduced due to a vehicle ahead casting off water, snow, or sand from its
tires and onto your windshield.
 


 The luggage compartment is loaded with heavy objects or the rear passenger seats are
occupied.
 


 Ice, snow, or soiling is on the front surface of the front emblem.



 During inclement weather such as rain, snow, or sand storms.



 When driving near facilities or objects emitting strong radio waves. 



 Under the following conditions, the radar sensor (front) may not be able to detect
vehicles ahead or obstructions.
 


 The beginning and end of a curve.



 Roads with continuous curves.



 Narrow lane roads due to road construction or lane closures.



 The vehicle ahead enters the radar sensor's blind spot.



 The vehicle ahead is running abnormally due to accident or vehicle damage.



 Roads with repeated up and down slopes



 Driving on poor roads or unpaved roads.



 The distance between your vehicle and the vehicle ahead is extremely short.



 A vehicle suddenly comes close such as by cutting into the lane. 



 To prevent incorrect operation of the system, use tires of the same specifi ed size,
manufacturer, brand, and tread pattern on all four wheels. In addition, do not use tires
with signifi cantly different wear patterns or tire pressures on the same vehicle (Including
the temporary spare tire).
 


 If the battery power is weak, the system may not operate correctly.
 When driving on roads with little traffi c and few vehicles ahead or obstructions for
the radar sensor (front) to detect, “Front Radar Sensor Blocked” may be temporarily
displayed, however, this does not indicate a problem.

CX-9_8FS7-EA-16K_Edition2.indb 141CX-9_8FS7-EA-16K_Edition2.indb 1412016/12/15 18:34:362016/12/15 18:34:36

Page 293 of 612

4–14 5
When Driving
i-ACTIVSENSE
NOTE
 


 The detection ability of the radar sensors (rear) has limitations. In the following cases,
the detection ability may lower and the system may not operate normally.
 


 The rear bumper near the radar sensors (rear) has become deformed.



 Snow, ice or mud adheres to the radar sensors (rear) on the rear bumper.



 Under bad weather conditions such as rain, snow and fog. 



 Under the following conditions, the radar sensors (rear) cannot detect target objects or it
may be diffi cult to detect them.




 Stationary objects on a road or a road side such as small, two-wheeled vehicles,
bicycles, pedestrians, animals, and shopping carts.
 


 Vehicle shapes which do not refl ect radar waves well such as empty trailers with a low
vehicle height and sports cars.
 


 Vehicles are shipped with the direction of the radar sensors (rear) adjusted for each
vehicle to a loaded vehicle condition so that the radar sensors (rear) detect approaching
vehicles correctly. If the direction of the radar sensors (rear) has deviated for some
reason, have the vehicle inspected at an Authorized Mazda Dealer.
 


 For repairs or replacement of the radar sensors (rear), or bumper repairs, paintwork,
and replacement near the radar sensors, consult an Authorized Mazda Dealer.
 


 Turn off the system while pulling a trailer or while an accessory such as a bicycle carrier
is installed to the rear of the vehicle. Otherwise, the radio waves emitted by the radar will
be blocked causing the system to not operate normally.
 


 The radar sensors are regulated by the relevant radio wave laws of the country in which
the vehicle is driven. If the vehicle is driven abroad, authorization from the country in
which the vehicle is driven may be required.

CX-9_8FS7-EA-16K_Edition2.indb 145CX-9_8FS7-EA-16K_Edition2.indb 1452016/12/15 18:34:382016/12/15 18:34:38

Page 388 of 612

5–70
Interior Features
Audio Set
Settings
 





 NOTE
Depending on the grade and specifi cation, the screen display may differ.
Select the icon on the home screen and display the Settings screen.
Switch the tab and select the setting item you want to change.
You can customize settings in the setup display as follows:

Tab Item Function
AD-Disp Height
Brightness Control
Other Refer to Active Driving Display on page
4-29 .
Display Refer to Volume/Display/Sound Controls on page 5-24 .
Safety Smart City Brake Support
Blind Spot Monitoring Volume
Other Refer to Personalization Features on page
9-11 .
Sound Refer to Volume/Display/Sound Controls on page 5-24 .
Clock Adjust Time Displays the currently set time is displayed.
Press
to advance the hour/minute, and select
to move the hour/minute back.
AM/PM can only be selected with the 12-hour
clock display.
GPS Sync Synchronizes with GPS when turned on.
When turned off, the time can be changed from
“Adjust Time”.
Time Format Changes the display between 12 and 24-hour
clock time.
Time Zone Select When it's not synchronized with GPS, select
the region you want to specify.
Daylight Savings Time Turns the daylight saving time setting on/off.
When ON, the time advances 1 hour. When
OFF, it returns to normal time.
Vehicle Rain Sensing Wiper
Door Locks
Other Refer to Personalization Features on page
9-11 .
Devices Bluetooth Refer to Bluetooth
® Preparation on page
5-43 .
CX-9_8FS7-EA-16K_Edition2.indb 70CX-9_8FS7-EA-16K_Edition2.indb 702016/12/15 18:35:402016/12/15 18:35:40

Page 436 of 612

6–24
Maintenance and Care
Owner Maintenance
Closing the Hood
1. Check under the hood area to make
certain all fi ller caps are in place and all
loose items (e.g. tools, oil containers,
etc.) have been removed.
2. Lift the hood, grasp the padded area on
the support rod, and secure the support
rod in the clip. Verify that the support
rod is secured in the clip before closing
the hood.


Clip
ClipClip

3. Lower the hood slowly to a height of
about 20 cm (7.9 in) above its closed
position and then let it drop.

CAUTION
When closing the hood, do not push
it excessively such as by applying your
weight. Otherwise, the hood could be
deformed.

CX-9_8FS7-EA-16K_Edition2.indb 24CX-9_8FS7-EA-16K_Edition2.indb 242016/12/15 18:36:002016/12/15 18:36:00

Page 458 of 612

6–46
Maintenance and Care
Owner Maintenance
*Some models.
CAUTION
 


 Do not use your temporary spare tire
rim with a snow tire or a conventional
tire. Neither will properly fi t and could
damage both tire and rim.
 


 The temporary spare tire has a tread life
of less than 5,000 km (3,000 miles). The
tread life may be shorter depending on
driving conditions.
 


 The temporary spare tire is for limited
use, however, if the tread wear solid-
band indicator appears, replace the tire
with the same type of temporary spare
(page 6-45 ).

NOTE
Tires degrade over time, even when
they are not being used on the road. It
is recommended that tires generally be
replaced when they are 6 years or older.
Heat caused by hot climates or frequent
high loading conditions can accelerate
the aging process. You should replace the
spare tire when you replace the other road
tires due to the aging of the spare tire. The
period in which the tire was manufactured
(both week and year) is indicated by a
4-digit number.
Refer to Tire Labeling on page 8-24 .

Replacing a Wheel
WARNING
Always use wheels of the correct size on
your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be aff ected, leading to loss of
control and an accident.

CAUTION
A wrong-sized wheel may adversely
aff ect:




 Tire fi t



 Wheel and bearing life



 Ground clearance



 Snow-chain clearance



 Speedometer calibration



 Headlight aim



 Bumper height



 Tire Pressure Monitoring System *
NOTE




 When replacing a wheel, make sure
the new one is the same as the original
factory wheel in diameter, rim width,
and offset (inset/outset).
 


 For details, contact an Authorized
Mazda Dealer.


Proper tire balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tires can cause
vibration and uneven wear, such as
cupping and fl at spots.
CX-9_8FS7-EA-16K_Edition2.indb 46CX-9_8FS7-EA-16K_Edition2.indb 462016/12/15 18:36:122016/12/15 18:36:12

Page 560 of 612

8–24
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
Tire Labeling
Federal law requires tire manufacturers to place standardized information on the sidewall of
all tires. This information identifi es and describes the fundamental characteristics of the tire
and also provides a tire identifi cation number for safety standard certifi cation and in case of
a recall.
Information on Passenger Vehicle Tires
Please refer to the sample below.


1. TIN: U.S. DOT tire identifi cation number
2. Passenger car tire
3. Nominal width of tire in millimeters
4. Ratio of height to width (aspect ratio)
5. Radial
6. Run-fl at tire
7. Rim diameter code
8. Load index & speed symbol
9. Severe snow conditions
10. Tire ply composition and materials used
11. Max. load rating
12. Tread wear, traction and temperature grades
13. Max. permissible infl ation pressure
14. SAFETY WARNING

P215/65R15 95H is an example of a tire size and load index rating. Here is an explanation
of the various components of that tire size and load index rating. Note that the tire size and
load index rating may be different from the example.
CX-9_8FS7-EA-16K_Edition2.indb 24CX-9_8FS7-EA-16K_Edition2.indb 242016/12/15 18:36:572016/12/15 18:36:57

Page 561 of 612

8–25
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
P
Indicates a tire that may be installed on cars, SUVs, minivans and light trucks as designated
by the Tire and Rim Association (T&RA).
NOTE
If your tire size does not begin with a letter this may mean it is designated by either ETRTO
(European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing
Association).

215
“215” is the nominal width of the tire in millimeters. This three-digit number gives the
width in millimeters of the tire from sidewall edge to sidewall edge. In general, the larger
the number, the wider the tire.
6 5
“65” is the aspect ratio. This two-digit number indicates the tire's ratio of height to width.
R
“R” is the tire construction symbol. R indicates “Radial ply construction”.
1 5
“15” is the wheel rim diameter in inches.
9 5
“95” is the Load Index. This two-or three-digit number indicates how much weight each tire
can support.
H
“H” is the speed rating. The speed rating denotes the maximum speed for which the use of
the tire is rated.

Letter Rating Speed Rating
Q 99 mph
R 106 mph
S 112 mph
T 118 mph
U 124 mph
H 130 mph
V 149 mph
W 168
* mph
Y 186 * mph
* For tires with a maximum speed capability over 149 mph, tire manufacturers sometimes
use the letters ZR. For tires with a maximum speed capability over 186 mph, tire
manufacturers always use the letters ZR.

CX-9_8FS7-EA-16K_Edition2.indb 25CX-9_8FS7-EA-16K_Edition2.indb 252016/12/15 18:36:582016/12/15 18:36:58

Page 564 of 612

8–28
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
Information on Temporary Tires
Please refer to the sample below.


1. Temporary tires
2. Nominal width of tire in millimeters
3. Ratio of height to width (aspect ratio)
4. Diagonal
5. Rim diameter code
6. Load index & speed symbol

T115/70D16 90M is an example of a tire size and load index rating. Here is an explanation
of the various components of that tire size and load index rating. Note that the tire size and
load index rating may be different from the example.
T
Indicates a tire that may be installed on cars, SUVs, minivans and light trucks as designated
by the Tire and Rim Association (T&RA).
1 1 5
“115” is the nominal width of the tire in millimeters. This three-digit number gives the width
in millimeters of the tire from sidewall edge to sidewall edge. In general, the larger the
number, the wider the tire.
7 0
“70” is the aspect ratio. This two-digit number indicates the tire's ratio of height to width.
D
“D” is the tire construction symbol. D indicates “diagonal ply construction”.
1 6
“16” is the wheel rim diameter in inches.
CX-9_8FS7-EA-16K_Edition2.indb 28CX-9_8FS7-EA-16K_Edition2.indb 282016/12/15 18:36:582016/12/15 18:36:58

Page 591 of 612

9–5
Specifi cations
Specifi cations
Capacities

(Approximate Quantities)
Item Capacity
Engine oil With oil fi lter replacement 4.8 L (5.1 US qt, 4.2 Imp qt)
Without oil fi lter replacement 4.6 L (4.9 US qt, 4.0 Imp qt)
Coolant U.S.A. and Canada 9.9 L (10.5 US qt, 8.7 Imp qt)
Mexico 9.8 L (10.4 US qt, 8.6 Imp qt)
Automatic transaxle fl uid 8.0 L (8.5 US qt, 7.0 Imp qt)
Transfer case oil 0.45 L (0.48 US qt, 0.40 Imp qt)
Rear differential oil 0.45 L (0.48 US qt, 0.40 Imp qt)
Fuel tank 2WD 72.0 L (19.0 US gal, 15.8 Imp gal)
AWD 74.0 L (19.5 US gal, 16.3 Imp gal)
Check oil and fl uid levels with dipsticks or reservoir gauges.

Dimensions
U.S.A. and Canada
Item Vehicle specifi cation
Overall length 5,075 mm (199.8 in)
Overall width 1,969 mm (77.5 in)
Overall height 1,752 mm (69.0 in)
Front tread 1,663 mm (65.5 in)
Rear tread 1,663 mm (65.5 in)
Wheelbase 2,930 mm (115.4 in)

Mexico
Item Vehicle specifi cation
Overall length 5,075 mm (199.8 in)
Overall width 1,969 mm (77.5 in)
Overall height 1,747 mm (68.8 in)
Front tread 1,663 mm (65.5 in)
Rear tread 1,663 mm (65.5 in)
Wheelbase 2,930 mm (115.4 in)

CX-9_8FS7-EA-16K_Edition2.indb 5CX-9_8FS7-EA-16K_Edition2.indb 52016/12/15 18:37:102016/12/15 18:37:10

Page:   < prev 1-10 11-20