window MAZDA MODEL MPV 2005 (in English) Owner's Manual

Black plate (176,1)
Operating Tips
qOperating the Climate Control
System
Operate the climate control system with
the engine running.
NOTE
To prevent the battery from being
discharged, do not leave the fan control
dial on for a long period of time when
the engine is not running.
qClearing the Air Inlet
Clear all obstructions like leaves, snow
and ice from the hood and the air inlet in
the cowl grille to improve the system
efficiency.
qFoggy Windows
The windows may fog up easily in humid
weather. Use the climate control system to
defog the windows.
To help defog the windows, operate the
air conditioner to dehumidify the air.
qOutside/Recirculated Air Position
Use the outside air position in normal
conditions. The recirculated air position
should be used only when driving on
dusty roads or for quick cooling of the
interior.
qParking in Direct Sunlight
If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then run
the climate control system.
qNot Using for a Long Period
Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
qCheck the Refrigerant before the
Weather Gets Hot
Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
efficient. Consult an Authorized Mazda
Dealer for refrigerant inspection.
The air conditioner is filled with
HFC134a (R134a), a refrigerant that will
not damage the ozone layer.
If the air conditioner is low on refrigerant
or has a malfunction, consult an
Authorized Mazda Dealer.
qReplacement of the Cabin Air
Filter
If your vehicle is equipped with an air
filter for the air conditioner, it is necessary
to change the filter periodically as
indicated in scheduled maintenance (page
8-3). Consult an Authorized Mazda
Dealer for replacement of the cabin air
filter.
6-2
Interior Comfort
Climate Control System
Mazda MPV_8T50-EA-04G_Edition1 Page176
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (179,1)
Control Panel (Front)
A/C0123
4
0123REAR
Temperature control dialA/C switch Rear window defroster switchFan control dial
Air intake selector switch
Rear air-conditioner main switchMode selector dial
qControl Switches
Temperature control dial
ColdHot
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
Fan control dial
This dial allows variable fan speeds.
0―Fan off
1―Low speed
2―Medium low speed
3―Medium high speed
4―High speed
Interior Comfort
Climate Control System
6-5
Mazda MPV_8T50-EA-04G_Edition1 Page179
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (181,1)
WARNING
The Recirculated Air Position:
Using the
position in cold or
rainy weather will cause the windows
to fog up. Your vision will be
hampered, which could lead to a
serious accident. Do not use the
position in cold or rainy weather.
Rear window defroster switch
When using the rear window defroster
switch, refer to Rear Window Defroster
(page 5-37).
qHeating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidified heating is desired, turn
on the air conditioner.
NOTE
lIf the windshield fogs up easily, set
the mode selector dial to the
position.
lIf cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
qCooling (With Air Conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner.
5. Adjust the fan control dial and
temperature control dial to maintain
maximum comfort.
CAUTION
When using the air conditioner while
driving up long hills or in heavy traffic,
closely monitor the temperature gauge
(page 5-22).
The air conditioner may cause engine
overheating. If the gauge indicates
overheating, turn the air conditioner off.
Interior Comfort
Climate Control System
6-7
Mazda MPV_8T50-EA-04G_Edition1 Page181
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (182,1)
NOTE
lWhen maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the
position,
then set the fan control dial to
position 4.
lIf warmer air is desired at floor level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
lThe air to the floor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
qVentilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the
position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
qWindshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
WARNING
Foggy Windshield:
Using the
position with the
temperature control set to the cold
position will cause the outside of the
windshield to fog up. Your vision will
be hampered, which could lead to a
serious accident. Set the temperature
control to the hot or warm position
when using the
position.
NOTE
lFor maximum defrosting, set the
temperature control dial to the
extreme hot position and the fan
control dial to position 4.
lIf warm air is desired at the floor, set
the mode selector dial to the
position.
lIn theorposition, air
conditioning is automatically turned
on to defrost the windshield quickly
(however, the indicator light does not
illuminate) and the
position is
automatically selected. The air intake
selector switch cannot be changed to
the
position.
qDehumidifying (With Air
Conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.
1. Set the mode selector dial to the
desired position.
2. Set the air intake selector to the
position.
6-8
Interior Comfort
Climate Control System
Mazda MPV_8T50-EA-04G_Edition1 Page182
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (277,1)
Wiper Blades
CAUTION
lHot waxes applied by automatic car
washers have been known to affect
the wiper's ability to clean windows.
lTo prevent damage to the wiper
blades, don't use gasoline, kerosene,
paint thinner, or other solvents on or
near them.
Contamination of either the windshield or
the blades with foreign matter can reduce
wiper effectiveness. Common sources are
insects, tree sap, and hot wax treatments
used by some commercial car washes.
If the blades are not wiping properly,
clean the window and blades with a good
cleaner or mild detergent; then rinse
thoroughly with clean water. Repeat if
necessary.
qReplacing Windshield Wiper
Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
To prevent damage to the wiper arms
and other components, don't move the
wipers by hand.1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clip
CAUTION
To prevent damage to the windshield,
don't let the wiper arm fall on it.
2. Hold the end of the rubber and pull
until the tabs are free of the metal
support.
Metal support
Ta b
Maintenance and Care
Owner Maintenance
8-21
Mazda MPV_8T50-EA-04G_Edition1 Page277
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (278,1)
3. Remove the metal stiffeners from the
blade rubber and install them in new
blades.
CAUTION
lDon't bend or discard the stiffeners.
You need to use them again.
lIf the metal stiffeners are switched,
the blade's wiping efficiency could
be reduced.
So don't use the driver's side metal
stiffeners on the passenger's side, or
vice versa.
lBe sure to reinstall the metal
stiffeners in the new blade rubber so
that the curve is the same as it was in
the old blade rubber.4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
NOTE
Install the blade so that the tabs are
toward the bottom of the wiper arm.
qReplacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, don't move the
wiper by hand.
8-22
Maintenance and Care
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page278
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (279,1)
1. Raise the wiper arm and turn the blade
assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clip
CAUTION
To prevent damage to the rear window,
don't let the wiper arm fall on it.
2. Pull down the blade rubber and slide it
out of the blade holder.
3. Remove the metal stiffeners from the
blade rubber and install them in new
blades.
CAUTION
Don't bend or discard the stiffeners.
You need to use them again.
4. Carefully insert the new blade rubber.
Then install the blade assembly in the
reverse order of removal.
Maintenance and Care
Owner Maintenance
8-23
Mazda MPV_8T50-EA-04G_Edition1 Page279
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (294,1)
qFuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 DEFOG 40ARear window
defroster
2 BTN 60ASTOP,
HAZARD,
ROOM,
D.LOCK and
DRL fuses
3 ABS 60AAntilock brake
system
í, For
protection of
various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEAT 30ARear heater
í,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
8 IG KEY2 40AA/C, P.WIND
í,
MOONROOFí
and R.WIP fuses
9 A/C 10AAir conditioner,
For protection of
various circuits
10 TAIL 15A Taillights
11 AC PWR 15A Inverter
12 HORN 15A Horn
13 FOG 15AFor protection of
various circuits
14 EEC 5AFor protection of
various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 HID L 20A―
18 HID R 20A―
8-38
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page294
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (296,1)
Fuse block (Driver's side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 P.WIND 30APower
windows
í, For
protection of
various circuits
2 WIPER 20AWindshield
wipers and
washer
3 SUN ROOF 15A
Moonroofí, For protec-
tion of various circuits
4 R.WIP 10ARear window
wiper and washer
5 SEAT 20AFor protection of
various circuits
6 M.DEF 10AMirror
defroster
í, For
protection of
various circuits
7 A/C 10AAir conditioner,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
8 DRL 10AFor protection of
various circuits
9―――
10 H/CLEAN 20AFor protection of
various circuits
11―――
12 HAZARD 10AHazard warning
flashers
13 ROOM 15AOverhead lights,
Map lights,
Luggage
compartment
light
14 AUX POWER 25A Accessory socket
15 CLOSER LH 20AFor protection of
various circuits
16 AUDIO 10AAudio system,
For protection of
various circuits
8-40
Maintenance and Care
íSome models.
Owner Maintenance
Mazda MPV_8T50-EA-04G_Edition1 Page296
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G

Black plate (297,1)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
17 D.LOCK 30APower door
locks
í, For
protection of
various circuits
18 P/SEAT 30A Power seat
í
19 ENGINE 10AEngine control
system
20 METER 10AInstrument
cluster
21 STOP 15A Brake lights
22 CLOSER RH 20AFor protection of
various circuits
23 ACC.DELAY 30APower windows
delay, For
protection of
various circuits
24 METER 15AInstrument
cluster, INH
switch
25 ST.SIGN 10A Starter signal
26 CIGAR 25A Lighter
27―――
28―――
Maintenance and Care
Owner Maintenance
8-41íSome models. Mazda MPV_8T50-EA-04G_Edition1 Page297
Monday, June 28 2004 4:0 PM
Form No.8T50-EA-04G