light MAZDA MODEL MX-5 2017 Owner's Manual - RHD (UK, Australia) (in English)

6–61
Maintenance and Care
Appearance Care
Convertible Top (Retractable
Fastback) Maintenance
W a s h i n g
To help protect the retractable fastback's
¿ nish, use a soft cloth or sponge to wash
it.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the ¿ nish if they are not removed
immediately. When prompt washing with
plain water is ineffective use a mild soap
made for use on vehicles.
CAUTION
  Do not use an automatic car wash. 
 Do not spray water directly on the
area where the window glass and the
retractable fastback meet. This would
probably cause water to enter the
cabin.
  Do not use strong soap, chemical
detergents, or hot water, and do not
wash the retractable fastback in
direct sunlight or when the surface is
warm.
Thoroughly rinse with lukewarm or cold
water. Do not allow soap to dry on the
¿ nish.
Waxing
Wax the retractable fastback when water
no longer beads on the paint. Always wash
and dry it before waxing.
CAUTION
  Wiping off dust or dirt with a dry
cloth will scratch the ¿ nish.

 Do not use abrasive wax. This may
damage the protective coating and
discolour or deteriorate the paint.
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas.
Drainage outlet cleaning procedure
There are drainage outlets on the left and
right of the lower side of the rear window.
Rear roofDrainage
outlet
Rear window
/:A(.'',A'FKVKQPKPFD

6–63
Maintenance and Care
Appearance Care
6. After cleaning is ¿ nished, continue
pressing the retractable fastback switch
in the close direction to close the rear
roof.
Refer to Closing the Roof on page
3-52 . Plastic Part Maintenance
 












 When cleaning the plastic lenses of
the lights, do not use petrol, paraf¿ n,
recti¿ ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signi¿ cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, À ush with water
immediately.
 


 If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or À uids such as petrol,
oil, engine coolant, or battery À uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or À uids using a soft
cloth immediately.
 


 High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
 


 Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
 


 In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
/:A(.'',A'FKVKQPKPFD

6–64
Maintenance and Care
Appearance Care
Interior Care
WARNING
Do not spray water into the vehicle
cabin:
Spraying water into the vehicle cabin
is dangerous as electrical devices such
as the audio and switches could get wet
resulting in a malfunction or vehicle
¿ re.
NOTE

 Do not wipe the interior using
alcohol, chlorine bleach, or organic
solvents such as thinner, benzene,
and petrol. Otherwise, it may cause
discolouration or stains.
  Rubbing hard with a stiff brush or
cloth may cause damage.
If the vehicle interior becomes soiled
by any of the following, wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or peeling
of the coating, and it will make it hard to
wipe off later.
 


 Beverage or fragrance



 Grease or oil



 Soiling
Seat Belt Maintenance
1. Clean the soiled area by lightly dabbing
it with a soft cloth soaked in a mild
detergent (approx. 5%) diluted with
water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
3. Before retracting seat belts which have
been pulled out for cleaning, dry them
off thoroughly and make sure there is
no remaining moisture on them.
WARNING
If a seat belt appears frayed or has
abrasions, have it replaced by an
Authorised Mazda Repairer:
If a seat belts is used under such a
condition, it cannot function at its full
capacity which could result in serious
injury or death.
Use a mild detergent to remove soiling
from a seat belt:
If organic solvents are used for
cleaning the seat belts or they become
stained or bleached, there is the
possibility of them becoming weakened
and as a result, they may not function
at their full capacity which could cause
serious injury or death.
NOTE
Clean seat belts diligently if they get
dirty. Leaving them uncleaned will make
it dif¿ cult to clean them later, and it may
affect the smooth retracting of the seat
belt.
/:A(.'',A'FKVKQPKPFD

6–65
Maintenance and Care
Appearance Care
*Some models.
Vinyl Upholstery Maintenance
Remove dust and dirt from the vinyl
upholstery using a brush or vacuum.
Remove soiling from vinyl upholstery
using a leather and vinyl upholstery
cleaner.
Upholstery Maintenance
1. Clean the soiled area by lightly dabbing
it with a soft cloth soaked in a mild
detergent (approx. 5%) diluted with
water.
2. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
NOTE
Rubbing the interior side of the soft top
vigorously with a stiff brush or cloth
may cause damage.
Leather Upholstery Maintenance *
1. Remove dust and sand using a vacuum
cleaner.
2. Wipe off the soiled area with a soft
cloth and a suitable, special cleaner or
a soft cloth soaked in a mild detergent
(about 5%) diluted with water.
3. Wipe off the remaining detergent using
a cloth soaked in clean water and
wrung out well.
4. Remove moisture with a dry, soft cloth
and allow the leather to further dry in
a well-ventilated, shaded area. If the
leather gets wet such as from rain,
remove the moisture and dry it as soon
as possible.
NOTE
  Because genuine leather is a natural
material, its surface is not uniform
and it may have natural scars,
scratches, and wrinkles.
  To maintain the quality for as long
as possible, periodical maintenance,
about twice a year, is recommended.
  If the leather upholstery comes into
contact with any of the following,
clean it immediately.
 Leaving it uncleaned could cause
premature wear, mold, or stains.
 


 Sand or dirt



 Grease or oil, such as hand cream



 Alcohol, such as in cosmetic or
hair dressing items
 
 If the leather upholstery gets wet,
promptly remove moisture with a
dry cloth. Remaining moisture on the
surface may cause deterioration such
as hardening and shrinkage.
  Exposure to direct sunlight for long
periods may cause deterioration
and shrinkage. When parking the
car under direct sunlight for long
periods, shade the interior using
sunshades.
  Do not leave vinyl products on
the leather upholstery for long
periods. They may affect the leather
quality and colouring. If the cabin
temperature becomes hot, the vinyl
may deteriorate and adhere to the
genuine leather.
/:A(.'',A'FKVKQPKPFD

7–1*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.
Parking in an Emergency ................... 7-2
Parking in an Emergency ............... 7-2
Roadside Emergency Triangle
Retaining Strap
* ............................. 7-2
Flat Tyre ............................................... 7-3
Flat Tyre
* ........................................ 7-3
Tool Storage ................................... 7-5
Emergency Flat Tyre Repair
Kit
* ................................................. 7-7
Changing a Tyre ........................... 7-14
Battery Runs Out .............................. 7-20
Jump-Starting ............................... 7-20
Emergency Starting .......................... 7-23
Starting a Flooded Engine ............ 7-23
Push-Starting ................................ 7-23
Overheating ....................................... 7-24
Overheating .................................. 7-24
When Fuel-Filler Flap Cannot be
Opened ............................................... 7-26
When Fuel-Filler Flap Cannot be
Opened ......................................... 7-26
Emergency Towing ............................ 7-27
Towing Description ...................... 7-27
Towing Hooks .............................. 7-28 Warning/Indicator Lights and Warning
Sounds ................................................ 7-31
If a Warning Light Turns On or
Flashes .......................................... 7-31
Message Indicated in Multi-
information Display
* .................... 7-46
Message Indicated on Display * .... 7-47
Warning Sound is Activated ......... 7-49
When Boot Lid Cannot be
Opened ............................................... 7-55
When Boot Lid Cannot be
Opened ......................................... 7-55
When the Roof Cannot be Closed.... 7-60
When the Roof Cannot be
Closed .......................................... 7-60
/:A(.'',A'FKVKQPKPFD

7–2
If Trouble Arises
Parking in an Emergency
*Some models.
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway in an emergency.
The hazard warning lights warn other
drivers that your vehicle is a traf¿ c hazard
and that they must take extreme caution
when near it.
Depress the hazard warning À asher and
all the direction indicators will À ash. The
hazard warning indicator lights in the
instrument cluster À ash simultaneously.
NOTE

 The direction indicators do not work
when the hazard warning lights are
on.
  Check local regulations about the use
of hazard warning lights while the
vehicle is being towed to verify that
it is not in violation of the law.
Roadside Emergency
Triangle Retaining Strap
*
Keep the roadside emergency triangle in
the boot end trim and secure it with the
strap.
Strap
/:A(.'',A'FKVKQPKPFD

7–3
If Trouble Arises
Flat Tyre
*Some models.
F l a t T y r e *
Either run-À at tyres or conventional tyres
are equipped on your Mazda depending on
the speci¿ cation, therefore the procedure
for repairing a À at tyre differs depending
on the type of tyre. Before driving, make
sure which type of tyre is equipped on
your Mazda. If you cannot identify your
tyre type, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
How to Identify Your Tyre Type
R u n -À at tyre
A run-À at tyre has a
and/or
indication on the side wall.
and/or
Conventional tyre
A conventional tyre does not have a
and/or indication on the side wall.
Vehicle with Run-À at Tyres
WARNING
Have the tyres checked or perform the
appropriate repair as soon as possible
by an expert repairer, we recommend
an Authorised Mazda Repairer:
When the À at tyre warning light
illuminates or the tyre pressure
warning beep sound is heard, it is
dangerous to drive the vehicle at
high speeds, or perform sudden
manoeuvring or braking. Vehicle
drivability could worsen and result in
an accident.
When the À at tyre warning light
illuminates or the tyre pressure
warning beep sound is heard, decrease
vehicle speed immediately and avoid
sudden manoeuvring and braking.
If a run-À at tyre is punctured, the FLAT
TIRE warning light illuminates in the
instrument cluster, and a beep sound is
heard for about 30 seconds.
NOTE
Until the À at tyre is changed, the beep
sound is heard for about 30 seconds
every time the ignition is switched ON.
/:A(.'',A'FKVKQPKPFD

7–7
If Trouble Arises
Flat Tyre
*Some models.
Emergency Flat Tyre
Repair Kit
*
The emergency À at tyre repair kit included
with your Mazda is for a temporary repair
of a slightly damaged À at tyre resulting
from running over nails or similar sharp
objects on the road surface.
Perform the emergency À at tyre repair
without removing the nail or similar sharp
object which punctured the tyre.
NOTE
Your vehicle is not equipped with a
spare tyre. In the event of a À at tyre,
use the emergency À at tyre repair kit
to repair the tyre temporarily. When
doing the repair, refer to the instructions
included in the emergency À at tyre
repair kit. If an emergency repair was
performed on a À at tyre using the
emergency À at tyre repair kit, have
an expert repairer, we recommend an
Authorised Mazda Repairer, repair or
replace the tyre as soon as possible.
About the Emergency Flat Tyre
Repair Kit
The emergency À at tyre repair kit includes
the following items.
Tyre sealant
Injection hoseCompressorValve core tool
Spare valve core
Speed restriction sticker Instructions
WARNING
Do not allow children to touch the tyre
sealant:
 
 Ingestion of tyre sealant is
dangerous. In the event tyre sealant
is accidentally swallowed, drink
large amounts of water immediately
and seek medical assistance.
  Tyre sealant that comes into contact
with the eyes and skin is dangerous.
If tyre sealant enters the eyes or
contacts the skin, À ush immediately
with large amounts of water and
seek medical assistance.
/:A(.'',A'FKVKQPKPFD

7–8
If Trouble Arises
Flat Tyre
NOTE
  The tyre sealant cannot be reused.
Purchase new tyre sealant at an
Authorised Mazda Repairer.
  The emergency À at tyre repair kit
cannot be used in the following
cases.
 Consult an expert repairer, we
recommend an Authorised Mazda
Repairer.
 


 The period of effective use for
the tyre sealant has expired. (The
period of effectiveness is indicated
on the bottle label.)
 


 The tear or puncture exceeds about
4 mm (0.16 in).
 


 The damage has occurred to an
area of the tyre other than the
tread.
 


 The vehicle has been driven with
nearly no air remaining in the tyre.
 


 The tyre has come off the wheel
rim.
 


 Damage to the wheel rim has
occurred.
 


 The tyre has two or more
punctures.
Using the Emergency Flat Tyre
Repair Kit
1. Move the vehicle off the right-of-way
to a safe place on a level and hard
surface where the vehicle does not
obstruct traf¿ c.
2. Shift the shift lever to the 1 or Reverse
(R) position for a manual transmission,
and shift the selector lever to the P
position for an automatic transmission.
3. Apply the parking brake with the brake
pedal depressed and turn off the engine. 4. If necessary, À ash the hazard warning
lights and set up the roadside
emergency triangle.
5. Unload passengers and cargo and
remove the emergency À at tyre repair
kit.
6. Shake the tyre sealant well.
CAUTION
If the bottle is shaken after the injection
hose is screwed on, tyre sealant could
spray out from the injection hose. Tyre
sealant contacting clothing or other
objects may be impossible to remove.
Shake the bottle before screwing on the
injection hose.
/:A(.'',A'FKVKQPKPFD

7–11
If Trouble Arises
Flat Tyre
WARNING
Do not adhere the speed restriction
sticker to the padded area on the
steering wheel:
Adhering the speed restriction sticker
to the padded area on the steering
wheel is dangerous because the air
bag may not operate (deploy) normally
resulting in serious injury. In addition,
do not adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
16. Pull out the air compressor hose and
the air compressor plug from the air
compressor.
Compressor hose
17. Install the air compressor hose to the
tyre valve.
Valve
Compressor hose
18. Insert the air compressor plug into the
accessory socket inside the vehicle and
switch the ignition to ACC.
Refer to Accessory Sockets on page
5-125 .
Compressor
Compressor plug
CAUTION
When inserting the air compressor
plug into or removing it from the
accessory socket, make sure that the air
compressor switch is off. When turning
the air compressor on/off, use the air
compressor switch.
19. Turn the air compressor switch on and
inÀ ate the tyre carefully to the correct
inÀ ation pressure.
/:A(.'',A'FKVKQPKPFD