buttons MAZDA MODEL MX-5 2017 Owners Manual (in English)

3–3
Before Driving
Keys
NOTE
The driver must carry the key to ensure the
system functions properly.


Auxiliary key Transmitter
Key code number plate

To use the auxiliary key, pull out the
auxiliary key from the transmitter while
pressing the knob.


Knob

Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors and
the fuel-¿ ller lid, and opens the trunk lid.
The system can start the engine without
having to take the key out of your purse or
pocket.
It can also help you signal for attention or
help.
Operating the theft-deterrent system is
also possible on theft-deterrent system-
equipped vehicles.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
For vehicles with the type A instrument
cluster, check the displayed message for
more information and, if necessary, have
the vehicle inspected at an Authorized
Mazda Dealer, according to the indication.
 


y KEY Warning Light (Red)
 Refer to Warning/Indicator Lights on
page 4-26 .




y Ignition Not Switched Off (STOP)
Warning Beep
  Refer to Ignition Not Switched Off
(STOP) Warning Beep on page 7-49 .
 


y Key Removed from Vehicle Warning
Beep
  Refer to Key Removed from Vehicle
Warning Beep on page 7-50 .

If you have a problem with the key,
consult an Authorized Mazda Dealer.

If your key is lost or stolen, consult an
Authorized Mazda Dealer as soon as
possible for a replacement and to make the
lost or stolen key inoperative.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–4
Before Driving
Keys
CAUTION
Radio equipment like this is governed
by laws in the United States.
Changes or modifi cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.

N O T E
 


y The keyless entry system operation may
vary due to local conditions.
 


y The keyless entry system is fully
operational (door/fuel-¿ ller lid lock/
unlock) when the ignition is switched
off. The system does not operate if the
ignition is switched to any position
other than off.
 


y If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be weak. To install a new battery,
refer to Key Battery Replacement (page
6-38 ).
 y Battery life is about one year. Replace
the battery with a new one if the KEY
indicator light (green) À ashes in the
instrument cluster (for vehicles with
a type A instrument cluster (page
4-26 ), messages are displayed in
the instrument cluster). Replacing
the battery about once a year is
recommended because the KEY warning
light/indicator light may not illuminate
or À ash depending on the rate of battery
depletion.


 


y Additional keys can be obtained at
an Authorized Mazda Dealer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorized Mazda Dealer when
additional keys are required.

Transmitter

Operation buttons Operation indicator light

N O T E
 


y The headlights turn on/off by operating
the transmitter. Refer to Leaving Home
Light on page 4-49 .
 


y (With theft-deterrent system) 
 The hazard warning lights À ash when
the theft-deterrent system is armed or
turned off.
  Refer to Theft-Deterrent System on page
3-49 .
 


y (With the advanced keyless function) 
 A beep sound can be heard for
con¿ rmation when the doors and the
fuel-¿ ller lid are locked/unlocked using
the key. If you prefer, the beep sound
can be turned off.
  The volume of the beep sound can also
be changed.
  Refer to Personalization Features on
page 9-9 .
  Use the following procedure to change
the setting.

1. Switch the ignition off and close
both of the doors and the trunk lid.
2. Open the driver's door.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–5
Before Driving
Keys
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.
Both of the doors and the fuel-
¿ ller lid lock and the beep sound
activates at the currently set volume.
The setting changes each time the
LOCK button on the key is pressed
and the beep sound activates at the
set volume. (If the beep sound has
been set to not activate, it will not
activate.)
4. The setting change is completed by
doing any one of the following:
 


y Switching the ignition to ACC or
ON.
 


y Closing the driver's door.



y Opening the trunk lid.



y Not operating the key for 10
seconds.
 


y Pressing any button except the
LOCK button on the key.
 


y Pressing a request switch.

The operation indicator light À ashes when
the buttons are pressed.
Lock button
To lock the doors and the fuel-¿ ller lid,
press the lock button and the hazard
warning lights will À ash once.
(With the advanced keyless function)
A beep sound will be heard once.

T o c o n¿ rm that both doors and the fuel-
¿ ller lid have been locked, press the lock
button again within 5 seconds. If they are
closed and locked, the horn will sound.


N O T E
 


y The doors and the fuel-¿ ller lid can be
locked by pressing the lock button while
any other door or the trunk lid is open.
The hazard warning lights will not À ash.

 When the lock button is pressed while
any door is open and then the door is
closed, both the doors and the fuel-¿ ller
lid are locked.
 


y Con¿ rm that both doors and the fuel-
¿ ller lid are locked visually or audibly
by use of the double click.
 


y Make sure both doors and the fuel-¿ ller
lid are locked after pressing the button.
 


y (With theft-deterrent system) 
 When the doors are locked by pressing
the lock button on the key while the
theft-deterrent system is armed, the
hazard warning lights will À ash once to
indicate that the system is armed.

Unlock button
To unlock the driver's door and the fuel-
¿ ller lid, press the unlock button and the
hazard warning lights will À ash twice.
(With the advanced keyless function)
A beep sound will be heard twice.

To unlock both doors and the fuel-¿ ller
lid, press the unlock button again within
3 seconds and two more beep sounds will
be heard.


/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–30
Before Driving
Mirrors
N O T E
 


y Do not use glass cleaner or suspend
objects on or around the light sensor.
Otherwise, light sensor sensitivity
will be affected and may not operate
normally.
 

Light sensor
 


y For information regarding the 3 buttons
(
, , ) on the auto-dimming
mirror.
  Refer to HomeLink Wireless Control
System on page 4-57 .
 y The auto-dimming function is canceled
when the ignition is switched ON and
the shift/selector lever is in reverse (R).

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–58
When Driving
Switches and Controls
WARNING
Do not use the HomeLink system with
any garage door opener that lacks the
safety stop and reverse feature:
Using the HomeLink system with any
garage door opener that lacks the
safety stop and reverse feature as
required by federal safety standards
is dangerous. (This includes garage
doors manufactured before April 1,
1982.)
Using these garage door openers can
increase the risk of serious injury or
death. For further information, contact
HomeLink at 1-800-355-3515 or www.
homelink.com or an Authorized Mazda
Dealer.

Always check the areas surrounding
garage doors and gates for people
or obstructions before programming
or during operation of the HomeLink
system:
Programming or operating the
HomeLink system without verifying
the safety of areas surrounding garage
doors and gates is dangerous and
could result in an unexpected accident
and serious injury if someone were to
be hit.

N O T E
The programming will not be erased even
if the battery is disconnected.

Pre-programming the HomeLink
System
N O T E
It is recommended that a new battery be
placed in the hand-held transmitter of the
device being programmed to HomeLink
for quicker training and accurate
transmission of the radio-frequency signal.
 


y Verify that there is a remote control
transmitter available for the device you
would like to program.
 


y Disconnect the power to the device.
Programming the HomeLink
System
CAUTION
When programming a garage door
opener or a gate, disconnect the power
to these devices before performing
programming. Continuous operation
of the devices could damage the
motor.

The HomeLink system provides 3 buttons
which can be individually selected and
programmed using the transmitters for
current, on-market devices as follows:

1. Disconnect the power to the garage
door opener or gate programmed to the
hand-held transmitter.
2. Position the end of your hand-held
transmitter 2.5—7.5 cm (1—3 inches)
away from the HomeLink button you
wish to program while keeping the
indicator light in view.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–59
When Driving
Switches and Controls
3. Simultaneously press and hold both
the chosen HomeLink and hand-held
transmitter buttons. Do not release
the buttons until step 3 has been
completed.
N O T E
Some gate operators and garage door
openers may require you to replace this
Programming Step 2 with procedures
noted in the “Gate Operator/Canadian
Programming” section.

4. After the HomeLink indicator light
changes from a slow to a rapidly
blinking light, release both the
HomeLink and hand-held transmitter
buttons.
N O T E
If the HomeLink indicator light does not
change to a rapidly blinking light, contact
HomeLink at www.homelink.com or call
1-800-355-3515 for assistance.

5. Connect the power to the garage door
opener or gate programmed to the
hand-held transmitter. 6. Firmly press and hold the programmed
HomeLink button for ¿ ve seconds,
and then release it. Perform this
operation two times to activate the door
or gate. If the door or gate does not
activate, press and hold the just-trained
HomeLink button and observe the
indicator light.
If the indicator light stays on
constantly, programming is complete
and your device should activate when
the HomeLink button is pressed and
released.
N O T E
To program the remaining two HomeLink
buttons, begin with “Programming” —
step 1

If the indicator light blinks rapidly
for two seconds and then turns
to a constant light, continue with
“Programming” steps 7—9 to
complete the programming of a rolling
code equipped device (most commonly
a garage door opener).
7. At the garage door opener receiver
(motor-head unit) in the garage, locate
the “learn” or “smart” button. This can
usually be found where the hanging
antenna wire is attached to the motor-
head unit.
8. Firmly press and release the “learn” or
“smart” button. (The name and color of
the button may vary by manufacturer.)
N O T E
Complete the programming within 30
seconds.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–60
When Driving
Switches and Controls
9. Return to the vehicle and ¿ rmly press,
hold for two seconds and release the
programmed HomeLink button. Repeat
the “ press/hold/release ” sequence a
second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process.

HomeLink should now activate your
rolling code equipped device.
N O T E
To program the remaining two HomeLink
buttons, begin with “Programming” —
step 1

For questions or comments, please contact
HomeLink at www.homelink.com or 1-
800-355-3515 .
Gate operator/Canadian
Programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
— which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are designed
to “time-out” in the same manner.

If you live in Canada or you are having
dif¿ culties programming a gate operator
by using the “Programming” procedures
(regardless of where you live), replace
“Programming HomeLink” step 3 with
the following:
N O T E
If programming a garage door opener or
gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating.

Continue to press and hold the HomeLink
button while you press and release
— every two seconds (“cycle”) your
hand-held transmitter until the frequency
signal has successfully been accepted by
HomeLink. (The indicator light will À ash
slowly and then rapidly.)
Proceed with “Programming” step 4 to
complete.
Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device. The
code will continue being transmitted for a
maximum of 20 seconds.
Reprogramming the HomeLink
system
To program a device to HomeLink using
a HomeLink button previously trained,
follow these steps:

1. Press and hold the desired HomeLink
button. DO NOT release the button.
2. The indicator light will begin to À ash
after 20 seconds. Without releasing
the HomeLink button, proceed with
“Programming” - step 1.

Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons (
, ) on
the auto-dimming mirror until the
HomeLink indicator light begins to À ash
after approximately 10 seconds.
Verify that the programming has been
erased when you resell the vehicle.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–28
Interior Features
Audio System
Operating the Radio
Band selector buttonChannel preset buttons
Scan button
Auto memory button
Tuning buttonAudio display

R a d i o O N
Press a band selector button (
) to
turn the radio on.
Band selection
Successively pressing the band selector
button (
) switches the bands as
follows: FM1
:FM2
:AM.

The selected mode will be indicated.
N O T E
If the FM broadcast signal becomes weak,
reception automatically changes from
STEREO to MONO for reduced noise.

Tuning
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning
Select the station by pressing the tuning
button (
, ) lightly. Seek tuning
Automatic search for radio stations starts
when the tuning button (
, ) is pressed
until a beep sound is heard. The search
stops when a station is found.
N O T E
If you continue to press and hold the
button, the frequency will continue
changing without stopping.

Scan tuning
Press and hold the scan button (
) to
automatically sample strong stations.
Scanning stops at each station for about 5
seconds. To hold a station, press and hold
the scan button (
) again during this
interval.
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.

1. To set a channel ¿ rst select AM, FM1,
or FM2. Tune to the desired station.
2. Press a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number or station
frequency will be displayed. The
station is now held in the memory.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–34
Interior Features
Audio System
Audio set [Type B (touchscreen)]
















N O T E
The explanation of functions described in this manual may differ from the actual
operation, and the shapes of screens and buttons and the letters and characters displayed
may also differ from the actual appearance.
Additionally, depending on future software updates, the content may successively change
without notice.

Audio Set (Type B) has three different human interfaces.  


y Commander switch



y Touch panel



y Voice recognition with steering switch and microphone
Commander switch operation
N O T E
For safety reasons, some operations are disabled while the vehicle is being driven.
Volume dial operation

Volume dial
Press the volume dial to switch the audio MUTE on and off.
Turn the volume dial to adjust the volume. The volume increases by turning the dial
clockwise, and decreases by turning it counterclockwise.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–46
Interior Features
Audio System
*Some models.
Operating the Satellite Radio *
What is satellite radio?
With over 130 channels, SiriusXM
Satellite Radio brings you more of what
you love. Get channels and channels of
commercial-free music, plus sports, news,
talk, entertainment and more.
Commercial-free music from nearly
every genre — rock to pop, hip-hop to
country, jazz, classical and more. Plus
live performances and artist-dedicated
channels.
Live sports Play-by-Play & Expert Talk
— every NFL game, every NASCAR
®
race, 24/7 sports talk, college sports and
more.
Exclusive entertainment, comedy and
talk — The biggest names, compelling
talk, hilarious comedy.
World-class news plus local traf¿ c and
weather.
Sign up for SiriusXM Satellite Radio
today!
N O T E
 


y To listen to SiriusXM, a prior
subscription (fee-based) is required.
 


y The channels which you can receive
depend on the package you subscribe
to.
 


y Satellite radio is broadcast as Sirius,
XM, and SiriusXM in the U.S.A.,
and Sirius and XM in Canada. In
this owner’s manual, only the name
SiriusXM is used.
 


y For traf¿ c and weather channels, map
information is not displayed and only
audio broadcasts can be received.
 y Call 877-447-0011
(U.S.A.)/877-209-0079 (Canada) to
activate. For more information, visit
www.siriusxm.com (U.S.A.)/www.
siriusxm.ca (Canada). Satellite radio
is only available in regions providing
satellite radio service (some areas of
the United States and Canada). Contact
Authorized Mazda Dealer for details.

How to Activate Satellite Radio
You must call SiriusXM to activate your
service. Activation is free and takes only a
few minutes.
New customers can receive a free
introductory subscription with a limited
term trial offer by calling 877-447-0011
(U.S.A.)/877-209-0079 (Canada) to
activate.
SiriusXM service uses an ID code to
identify your radio. This code is needed to
activate SiriusXM service, and report any
problems.

Please have the following information
ready:
 


y Radio ID (8-digit electronic serial No.)
Refer to Displaying the Radio ID (ESN)
 


y Valid credit card information (may not
be required at initial sign-up)

Be sure you are parked outside with a clear
view of open sky, you will be instructed
to turn on your radio (in SiriusXM mode
and tuned to channel 184 (Sirius)/1 (XM
and SiriusXM)). Activation typically takes
only 2—5 minutes.
Displaying the Radio ID (ESN)
When channel 0 is selected, the radio ID is
displayed. Use the PREVIOUS or NEXT
channel buttons to select channel 0.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD