reset MAZDA MODEL MX-5 2017 Owners Manual (in English)

3–11
Before Driving
Doors and Locks
*Some models.
N O T E
 
y Always stop the engine and lock the
doors. In addition, to prevent theft of
valuables, do not leave them inside the
cabin.
 


y If the key is left in the following areas
and you leave the vehicle, the doors
may be locked depending on the radio
wave conditions even if the key is left in
the vehicle.
 


y Around the dashboard



y In the storage compartments or the
center console
 


y Next to a communication device such
as a mobile phone
 

y When the ignition is switched to ACC
or ON, the vehicle lock-out prevention
feature prevents you from locking
yourself out of the vehicle.
  Both doors will automatically unlock if
they are locked using the power door
locks with any door open.
  If both the doors are closed even though
the trunk lid is open, both the doors will
lock.
  The vehicle lock-out prevention feature
does not operate while the ignition is
switched off.
  When any door is opened from the
outside while the key is inside the
vehicle, the closed doors are locked.
Both the doors are automatically
unlocked by closing the open door.
  (With the advanced keyless function) 
 The beep sound is heard for about 10
seconds to notify the driver that the key
has been left in the vehicle.
  (Without the advanced keyless
function)
  The horn sound is heard twice to notify
the driver that the key has been left in
the vehicle.

 


y (Door unlock (control) system with
collision detection) *   This system automatically unlocks the
doors in the event the vehicle is involved
in an accident to allow passengers to
get out of the vehicle immediately and
prevent being trapped inside. While the
ignition is switched ON and in the event
the vehicle receives an impact strong
enough to inÀ ate the air bags, both the
doors are automatically unlocked after
about 6 seconds have elapsed from the
time of the accident.
  The doors may not unlock depending on
how an impact is applied, the force of
the impact, and other conditions of the
accident.
  If door-related systems or the battery
is malfunctioning, the doors will not
unlock.
 


y When opening a door, the power
windows open a little automatically.
When closing the door, the power
windows close automatically. This is a
function for improving the sealability,
and it does not mean there is a problem.
  If the vehicle battery is disconnected for
vehicle maintenance or other reasons,
the power windows will not open
or close automatically. If the power
windows do not open or close, the
automatic open/close mechanism for the
windows must be reset.
  Refer to Operating the Power Windows
on page 3-31 .

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–32
Before Driving
Windows
Normal opening/closing
To open the window to the desired
position, lightly hold down the switch.
To close the window to the desired
position, lightly pull up the switch.

Master control switches
Driver's window
Open
Close


OpenClose

Auto-opening
To fully open the window automatically,
press the switch completely down.

To stop the window partway, pull or press
the switch in the opposite direction and
then release it.
N O T E
The power window cannot be fully closed
while the door is open.

Power window system initialization
procedure
If the battery was disconnected during
vehicle maintenance, or for other reasons
(such as a switch continues to be operated
after the window is open/closed), the
window will not fully open automatically.
Resetting of the automatic function can
be performed using the master control
switches or each passenger door switch.
The power window auto function reset
procedure can be done on both door
switches. The power window auto function
will only resume on the power window
that has been reset.

1. Close the doors and the convertible top.
2. Switch the ignition ON.
3. Make sure that the power window lock
switch located on the driver's door is
not depressed.
4. Press the switch and fully open the
window.
5. Pull up the switch to fully close the
window and continue holding the
switch for about 2 seconds after the
window fully closed.
6. Repeat Steps 4-5 for the passenger
power window while seated in the
passenger seat.
7. Make sure that the power windows
operate correctly using the door
switches.

After the system has been re-initialized,
passenger window can be fully opened
automatically using the master control
switches.

If the automatic power window operation
does not operate normally while the doors
or convertible top are opened/closed, reset
it using the previous procedures.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–35
Before Driving
Convertible Top (Soft Top)
CAUTION
 
¾ Remove leaves or other matter that may accumulate on and around the convertible top.
If leaves or other matter block the drain fi lter, water may enter the vehicle. Clean the drain
fi lter at least once a year.
  Refer to Convertible Top Maintenance on page 6-64 .



¾ Before opening the convertible top, make sure the rear window defogger switch is turned
off . Otherwise the heat generated from the defogger could damage the convertible top and
the internal material.
 


¾ Before lowering or raising the convertible top, stop in a safe place off the right-of-way and
park on a level surface.
 


¾ Make sure nothing is on the convertible top or near the back window when raising or
lowering the convertible top.
  Even small objects may interfere and cause damage.



¾ Do not drive through an automatic car wash; it may damage the convertible top.



¾ Do not raise or lower the convertible top when the temperature is below 5 °C (41 °F) ; this
will damage the convertible top material.
 


¾ Do not lower the convertible top when it's wet. If the convertible top dries while folded, it
will deteriorate and mold.
 


¾ Lowering the convertible top while it's wet can also cause water to drip into the passenger
compartment.
 

¾ Do not raise or lower the convertible top in a strong wind as it could damage the
convertible top or cause an unexpected accident.

N O T E
 


y The power windows go down automatically in conjunction with the convertible top
opening/closing. However, this is a function for improving the operability, and it does not
mean there is a problem. If the vehicle battery is disconnected for vehicle maintenance or
other reasons, the power windows will not go down automatically. If the power windows
do not go down, the automatic open/close mechanism for the windows must be reset.
  Refer to Operating the Power Windows on page 3-31 .



y The windblocker reduces the amount of wind coming into the cabin from behind when
driving with the convertible top opened.
  Refer to Windblocker on page 5-140 .

y When lowering the convertible top, make sure objects inside the vehicle are not blown
away by the wind.
 


y Secure all loose objects inside before driving with the convertible top down.



y To help prevent burglary or vandalism and to ensure that the passenger compartment
stays dry, close the convertible top securely and lock both doors when leaving the vehicle.
 

y The soft top is made of high quality material and if it is not maintained correctly, the
material could harden, becomes stained, or have an uneven gloss.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–42
Before Driving
Convertible Top (Retractable Fastback)
N O T E
 


y When opening the roof, make sure objects inside the vehicle are not blown away by the
wind.
 


y Secure all loose objects inside before driving with the roof down.



y To help prevent burglary or vandalism and to ensure that the passenger compartment
stays dry, close the roof securely and lock both doors when leaving the vehicle.
 


y The power windows lower automatically in conjunction with the roof opening/closing.
This is a function for improving the operability and it does not indicate a problem.
  If the vehicle battery is disconnected for vehicle maintenance or other reasons, the power
windows will not lower automatically. If the power windows do not lower, reset the power
window automatic open/close function.
  Refer to Operating the Power Windows on page 3-31 .



y The windblocker reduces the amount of wind coming into the cabin from behind when
driving with the roof opened.
  Refer to Windblocker on page 5-140 .
Operation Indication
Operation Indicator Light


When illuminated
This indicates that the roof is only partially open.
When À ashing
This indicates that the roof is being open/closed. (During switch operation)
When not illuminated
This indicates that the roof is open/closed fully.
N O T E
If the operation indicator light À ashes quickly, there may be a system malfunction. Consult
an Authorized Mazda Dealer.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

3–48
Before Driving
Security System
N O T E
 


y The keys carry a unique electronic code.
For this reason, and to assure your
safety, obtaining a replacement key
requires some waiting time. They are
only available through an Authorized
Mazda Dealer.
 


y Always keep a spare key in case one
is lost. If a key is lost, consult an
Authorized Mazda Dealer as soon as
possible.
 


y If you lose a key, an Authorized Mazda
Dealer will reset the electronic codes of
your remaining keys and immobilizer
system. Bring all the remaining keys to
an Authorized Mazda Dealer to reset.
  Starting the vehicle with a key that has
not been reset is not possible.

Operation
N O T E
 


y The engine may not start and security
indicator light may illuminate or À ash
if the key is placed in an area where it
is dif¿ cult for the system to detect the
signal, such as on the dashboard. Move
the key to a location within the signal
range, switch the ignition off, and then
restart the engine.
 


y Signals from a TV or radio station, or
from a transceiver or mobile telephone
could interfere with your immobilizer
system. If you are using the proper key
and the engine fails to start, check the
security indicator light.

Arming
The system is armed when the ignition is
switched from ON to off.
The security indicator light in the
instrument cluster À ashes every 2 seconds
until the system is disarmed.



Disarming
The system is disarmed when the
ignition is switched ON with the correct
programmed key. The security indicator
light illuminates for about 3 seconds and
then turns off. If the engine does not start
with the correct key, and the security
indicator light remains illuminated or
À ashing, try the following:
Make sure the key is within the
operational range for signal transmission.
Switch the ignition off, and then restart the
engine. If the engine does not start after
3 or more tries, contact an Authorized
Mazda Dealer.
N O T E
 


y If the security indicator light À ashes
continuously while you are driving,
do not shut off the engine. Go to an
Authorized Mazda Dealer and have it
checked. If the engine is shut off while
the indicator light is À ashing, you will
not be able to restart it.
 


y Because the electronic codes are
reset when the immobilizer system
is repaired, the keys are needed.
Make sure to bring all the keys to an
Authorized Mazda Dealer so that they
can be programmed.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–12
When Driving
Instrument Cluster and Display
Speedometer
The speedometer indicates the speed of the
vehicle.
Odometer, Trip Meter and Trip
Meter Selector (Without Multi-
information Display)
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.


Press the selector Press the selector
Press the selector Odometer
Trip meter A
Trip meter B
Selector


N O T E
When the ignition is switched to ACC or
off, the odometer or trip meters cannot be
displayed, however, pressing the selector
can inadvertently switch the trip meters or
reset them during an approximate ten-
minute period in the following cases:
 


y After the ignition is switched to off from
ON.
 


y After the driver's door is opened.
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.

For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is ¿ lled.

When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–13
When Driving
Instrument Cluster and Display
N O T E
 


y (Vehicles with type B audio) 
 If the fuel economy data is reset using
the fuel economy monitor, or trip A
is reset using the trip meter when the
function which synchronizes the fuel
economy monitor and the trip meter is
on, the fuel economy data and trip A are
reset simultaneously.
  Refer to Fuel Economy Monitor on page
4-69 .
 


y Only the trip meters record tenths of
kilometers (miles).
 


y The trip record will be erased when: 



y The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


y The vehicle is driven over 9999.9 km
(mile).


Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute (rpm).
CAUTION
Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.


Striped zone
Red zone

N O T E
When the tachometer needle enters the
STRIPED ZONE, this indicates to the
driver that the gears should be shifted
before entering the RED ZONE.

Engine Coolant Temperature
Gauge (Without Multi-information
Display)
Indicates engine coolant temperature.

CAUTION
If the high engine coolant temperature
warning light (red) turns on, there is
a possibility of overheating. Park the
vehicle in a safe place immediately
and take appropriate measures. If the
vehicle continues to be driven, it could
cause damage to the engine.
Refer to Overheating on page 7-27 .

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–16
When Driving
Instrument Cluster and Display
*Some models.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and Fahrenheit
using the following procedure.
(Vehicles with Type B)
Settings can be changed by operating the
center display screen.
Refer to Personalization Features on page
9-9 .
(Vehicles without Type B)

1. Press the INFO switch with the ignition
switched off and continue pressing the
INFO switch for 5 seconds or longer
while switching the ignition ON. The
outside temperature display À ashes.
2. Press the INFO switch to change the
outside temperature unit.
3. Press and hold the INFO switch for
3 seconds or longer while the outside
temperature display is À ashing. The
outside temperature display illuminates.

N O T E
When the temperature unit indicated in the
outside temperature display is changed,
the temperature unit indicated in the
engine coolant gauge display changes in
conjunction with it.

Cruise Control Set Vehicle Speed
Display (Without Multi-
information Display)
*
The vehicle speed preset using the cruise
control is displayed.



Trip Computer and INFO Switch
(Without Multi-information
Display)
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
 


y Approximate distance you can travel on
the available fuel
 


y Average fuel economy



y Current fuel economy



y Average vehicle speed
If you have any problems with your trip
computer, consult an Authorized Mazda
Dealer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.

The distance-to-empty will be calculated
and displayed every second.



/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–17
When Driving
Instrument Cluster and Display
N O T E
 


y Even though the distance-to-empty
display may indicate a suf¿ cient amount
of remaining driving distance before
refueling is required, refuel as soon as
possible if the fuel level is very low or
the low fuel warning light illuminates.
 


y The display may not change unless you
add more than approximately 9 L (2.3
US gal, 1.9 Imp gal) of fuel.
 


y The distance-to-empty is the
approximate remaining distance the
vehicle can be driven until all the
graduation marks in the fuel gauge
(indicating the remaining fuel supply)
disappear.
 


y If there is no past fuel economy
information such as after ¿ rst
purchasing your vehicle or the
information is deleted when the battery
cables are disconnected, the actual
distance-to empty/range may differ from
the amount indicated.

Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total traveled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed every
minute.



To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - L/100
km (- - - mpg) will be displayed for about
1 minute before the fuel economy is
recalculated and displayed.
Current fuel economy mode
This mode displays the current fuel
economy by calculating the amount of fuel
consumption and the distance traveled.

Current fuel economy will be calculated
and displayed every 2 seconds.



When you've slowed to about 5 km/h (3
mph), - - - L/100 km (- - - mpg) will be
displayed.
Average vehicle speed mode
This mode displays the average vehicle
speed by calculating the distance and the
time traveled since connecting the battery
or resetting the data.
Average vehicle speed will be calculated
and displayed every 10 seconds.



To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - km/h
(- - - mph) will be displayed for about
1 minute before the vehicle speed is
recalculated and displayed.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–20
When Driving
Instrument Cluster and Display
Odometer, Trip Meter and Trip
Meter Selector
The odometer is constantly displayed on
the screen when the ignition is switched
ON, and the TRIP A or TRIP B screen
can be displayed by operating the INFO
switch.


Press the INFO switchINFO switch
Trip meter A,
Odometer
Trip meter B,
Odometer

Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The driving distance for a speci¿ ed
interval is indicated. Two types (TRIP
A, TRIP B) of interval distance and the
average fuel economy for each can be
measured.

For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is ¿ lled.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter and average fuel economy
can be reset by pressing the INFO switch
for 1.5 second or more while in each
mode.
N O T E
 


y Only the trip meters record tenths of
kilometers (miles).
 


y The trip record will be erased when: 



y The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


y The vehicle is driven over 1999 km
(mile).


/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD