turn signal bulb MAZDA MODEL MX-5 2017 Owners Manual (in English)

4–50
When Driving
Switches and Controls
Turn and Lane-Change
Signals
The ignition must be switched ON to use
the turn and lane-change signals.
Turn Signals
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.

If the indicator light continues to À ash
after a turn, manually return the lever to its
original position.

Right turn
Left turn Right lane change
Left lane changeOFF

The turn signal indicators in the instrument
cluster À ash according to the operation of
the turn signal lever to show which signal
is working.



N O T E
 


y If an indicator light stays on without
À ashing or if it À ashes abnormally, one
of the turn signal bulbs may be burned
out.
 


y A personalized function is available to
change the turn indicator sound volume.
(page 9-9 )

Lane-Change Signals
Move the lever halfway toward the
direction of the lane change—until the
indicator À ashes— and hold it there. It will
return to the off position when released.
Three-Flash Turn Signal
After releasing the turn signal lever, the
turn signal indicator À ashes three times.
The operation can be cancelled by moving
the lever in the direction opposite to which
it was operated.
N O T E
The three-À ash turn signal function can be
switched to operable/inoperable using the
personalization function.
Refer to Personalization Features on page
9-9 .

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

6–45
Maintenance and Care
Owner Maintenance
Light Bulbs

Overhead light
Side turn signal lights
High-mount brake light
Trunk light
Front side-marker lights
Front turn signal lights
Headlights (low beam) Parking lights
Headlights (High beam)
Daytime running lights
License plate lights
Brake lights
Taillights
Rear side-marker lights
Reverse lights
Rear turn signal lights

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

6–47
Maintenance and Care
Owner Maintenance
5. Disconnect the bulb from the socket.



6. Install the new bulb in the reverse order
of the removal procedure.

Front side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.


Removal
Installation

4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Disconnect the bulb from the socket.



6. Install the new bulb in the reverse order
of the removal procedure.

Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.


Removal
Installation

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

6–48
Maintenance and Care
Owner Maintenance
4. Disconnect the connector from the unit
by pressing the tab on the connector
with your ¿ nger and pulling the
connector rearward.



5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the socket.


7. Install the new bulb in the reverse order
of the removal procedure.

Side turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left. 3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.


Removal
Installation

4. Remove the unit by pressing the tab on
the unit with your ¿ nger and pulling the
unit forward.



5. Detach the electrical connector from
the unit by pulling it to the rear.



6. Install the new side turn signal unit
in the reverse order of the removal
procedure.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

9–7
Speci¿ cations
Speci¿ cations
Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE *1 (SAE)
Headlights High beam LED *2 — (—)
Low beam LED *2 — (—)
Daytime running lights LED type LED *2 — (—)
Bulb type 21 W21W (7440)
Parking lights LED
*2 — (—)
Front side-marker lights
5 W5W (—)
Front turn signal lights 28/8 — (7444NA)
Side turn signal lights 5
*3 WY5W (—)
High-mount brake light LED *2 — (—)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-marker lights
5 W5W (—)
Brake lights LED
*2 — (—)
Taillights LED *2 — (—)
Reverse lights 21 W21W (7440)
License plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
*3 Bulb replacement is not possible because it is built into the unit. Replace the unit.




Interior light
Light bulb Category
Wattage UNECE *1
Overhead light 10 —
Trunk light 5 —
*1 UNECE stands for United Nations Economic Commission for Europe.


/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD