warning lights MAZDA MODEL MX-5 RF 2017 (in English) User Guide

3–14
Before Driving
Doors and Locks
NOTE
  You can also activate the system
by pressing the lock button on the
transmitter twice within 3 seconds.
 (With the advanced keyless
function)
 You can also activate the system by
pressing the request switch twice
within 3 seconds.
5. The indicator light illuminates for
about 3 seconds to indicate that the
system has been activated.
NOTE
The system cannot be activated when
any door is open.
How to Deactivate the System
Unlock the driver's door or switch the
ignition ON.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the system can only be deactivated by
unlocking a door with the auxiliary key.
Locking, Unlocking with Request
Switch (With the advanced keyless
function)
Both doors and the boot lid, fuel-¿ ller
À ap can be locked/unlocked by pressing
the request switch while the key is being
carried.
Request switch
To lock
To lock the doors and the boot lid, fuel-
¿ ller À ap, press the request switch and the
hazard warning lights will À ash once.
(Except European models)
A beep sound will be heard once.
To unlock
To unlock the doors and the boot lid, fuel-
¿ ller À ap, press the request switch and the
hazard warning lights will À ash twice.
(Except European models)
A beep sound will be heard twice.
NOTE
  Con¿ rm that both doors and the
boot lid, fuel-¿ ller À ap are securely
locked.
  Both doors and the boot lid, fuel-
¿ ller À ap cannot be locked when any
door is open.
/:A(.'',A'FKVKQPKPFD

3–15
Before Driving
Doors and Locks
NOTE
  It may require a few seconds for
the doors to unlock after the request
switch is pressed.
 (European models) The setting can be changed so that a
beep sound is heard for con¿ rmation
when the doors and the boot lid, fuel-
¿ ller À ap are locked/unlocked using
a request switch.
(Except European models) A beep sound is heard for
con¿ rmation when the doors and the
boot lid, fuel-¿ ller À apare locked/
unlocked using the request switch.
If you prefer, the beep sound can be
turned off.
 The volume of the beep sound
can also be changed. Refer to
Personalisation Features on page
9-10 .
NOTE
 Use the following procedure to
change the setting.
1. Switch the ignition off and close
both of the doors and the boot lid.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.
Both of the doors and the boot lid,
fuel-¿ ller À ap lock and the beep
sound activates at the currently
set volume. The setting changes
each time the LOCK button on the
key is pressed and the beep sound
activates at the set volume. (If the
beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed
by doing any one of the following:
 


 Switching the ignition to ACC
or ON.
 


 Closing the driver's door.



 Opening the boot lid.



 Not operating the key for 10
seconds.
 


 Pressing any button except the
LOCK button on the key.
 


 Pressing a request switch. 



(With theft-deterrent system) The hazard warning lights À ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on
page 3-55 .

(With double locking system) Pressing the request switch twice
within 3 seconds will activate the
double locking system.
 Refer to Double Locking System on
page 3-13 .
/:A(.'',A'FKVKQPKPFD

3–16
Before Driving
Doors and Locks
NOTE
  The setting can be changed so that
the doors and the boot lid, fuel-¿ ller
À ap are locked automatically without
pressing the request switch.
 Refer to Personalisation Features on
page 9-10 .
(Auto-lock function) A beep sound is heard when both
doors are closed while the advanced
key is being carried. Both doors
and the boot lid, fuel-¿ ller À ap are
locked automatically after about
three seconds when the advanced
key is out of the operational range.
Also, the hazard warning lights
À ash once. (Even if the driver is in
the operational range, both doors
and the boot lid, fuel-¿ ller À ap are
locked automatically after about
30 seconds.) If you are out of the
operational range before the doors
and the boot lid are completely
closed or another key is left in the
vehicle, the auto-lock function
will not work. Always make sure
that both doors and the boot lid are
closed and locked before leaving the
vehicle. The auto-lock function does
not close the power windows.
NOTE
 Auto re-lock function After unlocking with the request
switch, both doors and the boot lid,
fuel-¿ ller À ap will automatically lock
if any of the following operations
are not performed within about 30
seconds. If your vehicle has a theft-
deterrent system, the hazard warning
lights will À ash for con¿ rmation.
 The time required for the doors and
the boot lid, fuel-¿ ller À ap to lock
automatically can be changed.
 Refer to Personalisation Features on
page 9-10 .
 


 Opening a door or the boot lid.



 Switching the ignition to any
position other than off.
Locking, Unlocking with
Transmitter
Both doors and the boot lid, fuel-¿ ller À ap
can be locked/unlocked by operating the
keyless entry system transmitter, refer to
Keyless Entry System (page 3-3 ).
/:A(.'',A'FKVKQPKPFD

3–32
Before Driving
Mirrors
Rearview Mirror
WARNING
Do not stack cargo or objects higher
than the seatbacks:
Cargo stacked higher than the
seatbacks is dangerous. It can block
your view in the rearview mirror, which
might cause you to hit another car
when changing lanes.
Rearview mirror adjustment
Before driving, adjust the rearview mirror
to centre on the scene through the rear
window.
NOTE
For the manual antidazzle mirror,
perform the adjustment with the
antidazzle lever in the day position.
Reducing glare from headlights
Manual antidazzle mirror
Push the antidazzle lever forward for day
driving. Pull it back to reduce glare of
headlights from vehicles at the rear.
Antidazzle lever
Day Night
Auto-dimming mirror
The auto-dimming mirror automatically
reduces the glare of headlights from
vehicles at the rear when the ignition is
switched ON.
Press the ON/OFF button
to cancel the
auto-dimming function. The indicator light
will turn off.
To reactivate the auto-dimming function,
press the ON/OFF button
. The indicator
light will illuminate.
ON/OFF button Indicator light
/:A(.'',A'FKVKQPKPFD

3–55
Before Driving
Security System
*Some models.
Theft-Deterrent System *
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and À ashing the
hazard warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.
The intrusion sensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
 
 Do not hang clothing or objects from
a head restraint.
  Return the sunvisors to their original
positions.
  Do not blind the intrusion sensor by
covering it or placing objects over it.
  Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
  Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
  Do not install seats that are not
Mazda genuine products.
  To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

Intrusion sensor and
intrusion sensor bezel
/:A(.'',A'FKVKQPKPFD

3–56
Before Driving
Security System
Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights À ash for about
30 seconds when the system is triggered
by any one of the following:
 


 Unlocking a door with an inside door-
lock knob.
 


 Forcing open a door, the bonnet or the
boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
 


(With the intrusion sensor)
 The intrusion sensor detects a movement
in the vehicle.
The system will be triggered again (up to
10 times) if one of the above conditions
remains.
 


(With the intrusion sensor)
 Disconnecting the battery terminal (the
hazard warning lights do not À ash).
The system will be triggered about 10
times.
NOTE
  The boot lid does not open while the
theft-deterrent system is operating.
  If the battery goes dead while the
theft-deterrent system is armed,
the siren/horn will activate and the
hazard warning lights will À ash when
the battery is charged or replaced.
How to Arm the System
1. Close the windows and the convertible
top securely.
NOTE
(With the intrusion sensor)
The intrusion sensor function can be
armed only when the convertible top is
closed.
Even with a window open, the system
can be armed, however, leaving the
windows even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion Sensor
(With Intrusion Sensor) on page 3-57 .
2. Switch the ignition OFF.
3. Make sure the bonnet, convertible top,
the doors, and the boot lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will À ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument cluster À ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
/:A(.'',A'FKVKQPKPFD

3–57
Before Driving
Security System
NOTE
  The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors, the
boot lid and the bonnet closed.
 Refer to Transmitter on page 3-5 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door.



 Opening the bonnet.



 Switching the ignition ON.

 To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
À ash once to indicate that the system
is armed.
Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
(Intrusion sensor)
 


 Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
 


 Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
 


 Hanging small objects/accessories in the
vehicle, or placing other items which
can move easily inside the vehicle.
 


 Parking in an area where there is strong
vibration or loud noise.
 


 When using a high pressure or automatic
car wash.
 


 Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
 


 Doors are locked with a window left
open.
 


 An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the boot lid remains
closed for 30 seconds, both doors and
the boot lid automatically re-lock and
the theft deterrent system arms even if
a window or the convertible top is left
open.
/:A(.'',A'FKVKQPKPFD

3–58
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will À ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.
The hazard warning lights will À ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will À ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric boot lid opener
while the key is being carried.
The hazard warning lights will À ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the console box.
Mazda recommends that you af¿ x it to the
lower rear corner of a front door window.
/:A(.'',A'FKVKQPKPFD

4–1*Some models.4–1
4When Driving



Information concerning safe driving and stopping.
Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-11
i-stop
* ........................................... 4-13
Instrument Cluster and Display ...... 4-24
Meters and Gauges ....................... 4-24
Multi-information Display and INFO
Switch
* ......................................... 4-33
Warning/Indicator Lights ............. 4-42
Transmission ...................................... 4-48
Manual Transmission
Operation ...................................... 4-48
Automatic Transmission
Controls ........................................ 4-51
Switches and Controls ...................... 4-63
Lighting Control ........................... 4-63
Rear Fog Light
* ............................ 4-70
Turn and Lane-change Signals ..... 4-71
Windscreen Wipers and
Washer .......................................... 4-72
Headlight Washer
* ........................ 4-77
Rear Window Defogger ............... 4-77
Horn ............................................. 4-79
Hazard Warning Flasher ............... 4-79
Brake .................................................. 4-81
Brake System ............................... 4-81
Emergency Stop Signal System ... 4-84
Hill Launch Assist (HLA) ............ 4-84 ABS/TCS/DSC ................................... 4-86
Antilock Brake System (ABS) ..... 4-86
Traction Control System (TCS) ... 4-87
Dynamic Stability Control
(DSC) ........................................... 4-88
i-ELOOP ............................................ 4-90
i-ELOOP
* ..................................... 4-90
Fuel Economy Monitor ..................... 4-93
Fuel Economy Monitor
* ............... 4-93
Drive Selection ................................... 4-97
Drive Selection
* ........................... 4-97
Power Steering................................... 4-99
Power Steering ............................. 4-99
/:A(.'',A'FKVKQPKPFD

4–5
When Driving
Start/Stop Engine
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start has
been pressed to ACC, and the doors will
not lock/unlock even if they have been
locked manually.
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-42 ).
NOTE
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
/:A(.'',A'FKVKQPKPFD