MAZDA MODEL MX-5 RF 2017 Owners Manual (in English)
Page 541 of 609
7–47
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Message Indicated on Display *
            If a message is displayed in the centre display (Type B/type C audio), take appropriate 
action (in a calm manner) according to the displayed message.
(Display example)
 Stop Vehicle in Safe Place Immediately
    If the following messages are displayed in the centre display (Type B/type C audio), a 
vehicle system may be malfunctioning. Stop the vehicle in a safe place and contact an 
Authorised Mazda Repairer.
 Display   Indicated  Condition 
 Displays if the engine coolant temperature has increased 
excessively. 
 Displays if the charging system has a malfunction. 
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 542 of 609
7–48
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Verify Display Content
    Displays  in  the  following  cases:
 Display   Indicated Condition/Action to be taken 
 The following message is displayed when the 
temperature around the centre display is high.
  Lowering the temperature in the cabin or the 
temperature around the centre display by avoiding 
direct sunlight is recommended. 
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 543 of 609
7–49
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
 Warning Sound is 
Activated
 Lights-on  Reminder
              If  lights  are  on  and  the  ignition  is  switched 
to ACC or off, a continuous beep sound 
will be heard when the driver's door is 
opened.
 NOTE
        When the ignition is switched to 
ACC, the “Ignition Not Switched 
Off (STOP) Warning Beep” (page 
 7-51 ) overrides the lights-on 
reminder.  
        A personalised function is available 
to change the sound volume for the 
lights-on reminder. 
   Refer to Personalisation Features on 
page 9-10 . 
 Air Bag/Seat Belt Pretensioner 
System Warning Beep
              If  there  is  a  problem  with  the  air  bag/seat 
belt pretensioner systems and the warning 
light illumination, a warning beep sound 
will be heard for about 5 seconds every 
minute.
  The air bag and seat belt pretensioner 
system warning beep sound will continue 
to be heard for approximately 35 minutes. 
Have your vehicle inspected at an expert 
repairer, we recommend an Authorised 
Mazda Repairer as soon as possible.
 WARNING
 Do not drive the vehicle with the air 
bag/seat belt pretensioner system 
warning beep sounding: 
 Driving the vehicle with the air bag/
seat belt pretensioner system warning 
beep sounding is dangerous. In a 
collision, the air bags and the seat belt 
pretensioner system will not deploy and 
this could result in death or serious 
injury. Contact an expert repairer, 
we recommend an Authorised Mazda 
Repairer to have the vehicle inspected 
as soon as possible. 
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 544 of 609
7–50
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Active Bonnet Warning Beep *
              If  there  is  a  problem  with  the  active 
bonnet and the warning light illumination, 
a warning beep sound will be heard for 
about 5 seconds every minute.
    The active bonnet warning beep sound will 
continue to be heard for approximately 
35 minutes. Have your vehicle inspected 
at an expert repairer, we recommend an 
Authorised Mazda Repairer as soon as 
possible.
 WARNING
 Do not drive the vehicle with the active 
bonnet warning beep sounding: 
 Driving the vehicle with the active 
bonnet warning beep sounding 
is dangerous as the active bonnet 
mechanism may not activate normally 
and function as intended in the 
event the vehicle were to contact a 
pedestrian. Contact an expert repairer, 
we recommend an Authorised Mazda 
Repairer to have the vehicle inspected 
as soon as possible. 
 Seat Belt Warning Beep
              If  the  vehicle  speed  exceeds  about  20 
km/h (12 mph) with the driver or front 
passenger's seat belt unfastened, a warning 
beep sounds continuously. If the seat belt 
remains unfastened, the beep sound stops 
once and then continues for about 90 
seconds. The beep stops after the driver or 
front passenger's seat belt is fastened.
 NOTE
        Placing heavy items on the front 
passenger seat may cause the front 
passenger seat belt warning function 
to operate depending on the weight 
of the item. 
        To allow the front passenger seat 
weight sensor to function properly, 
do not place and sit on an additional 
seat cushion on the front passenger 
seat. The sensor may not function 
properly because the additional 
seat cushion could cause sensor 
interference.
        When a small child sits on the front 
passenger seat, it is possible that the 
warning beep will not operate. 
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 545 of 609
7–51
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Retractable  Fastback  Warning 
Beep*
              When  operating  the  retractable  fastback 
switch, the warning beep is activated when 
the retractable fastback operation begins 
and when it is completed.
  If there is a problem with the retractable 
fastback, the warning beep is activated 
continuously while operating the switch. If 
the warning beep is activated continuously 
while operating the switch, have the 
vehicle inspected at an expert repairer, 
we recommend an Authorised Mazda 
Repairer.
 Ignition Not Switched Off (STOP) 
Warning Beep
              E u r o p e a n   m o d e l s
    If the driver's door is opened with the 
ignition switched to ACC, a beep will 
be heard 6 times in the cabin to notify 
the driver that the ignition has not been 
switched OFF (STOP). Under this 
condition, the keyless entry system will 
not operate, the vehicle cannot be locked, 
and the battery voltage will be depleted.
  Except  European  models
    If the driver's door is opened with the 
ignition switched to ACC, a beep will 
be heard continuously in the cabin to 
notify the driver that the ignition has not 
been switched OFF (STOP). Under this 
condition, the keyless entry system will 
not operate, the vehicle cannot be locked, 
and the battery voltage will be depleted.
 Key Removed from Vehicle 
Warning Beep
              Vehicles  with  advanced  keyless  function
    If the key is taken out of the vehicle while 
the ignition is not switched OFF and 
all the doors are closed, the beep which 
sounds outside of the vehicle will be heard 
6 times, the beep which sounds inside 
the vehicle will be heard 6 times, and the 
KEY warning light (red) in the instrument 
cluster À ashes continuously to notify 
the driver that the ignition has not been 
switched OFF.
  Vehicles without advanced keyless 
function
    If the key is taken out of the vehicle while 
the ignition is not switched OFF and all 
the doors are closed, a beep will be heard 
in the cabin 6 times and the KEY warning 
light (red) in the instrument cluster turns 
on continuously to notify the driver that 
the ignition has not been switched OFF.
 NOTE
 Because the key utilizes low-intensity 
radio waves, the Key Removed From 
Vehicle Warning may activate if the key 
is carried together with a metal object 
or it is placed in a poor signal reception 
area.
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 546 of 609
7–52
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Request Switch Inoperable 
Warning Beep (With the advanced 
keyless function)
              If  the  request  switch  is  pressed  with  the 
door open or ajar, or the ignition is not 
switched OFF with a key being carried, 
a beep will be heard outside for about 2 
seconds to notify the driver that the door 
or boot lid cannot be locked.
 Key Left-in-boot Compartment 
Warning Beep (With the advanced 
keyless function)
              If  the  key  is  left  in  the  boot  with  all  the 
doors locked and the boot lid closed, a 
beep will be heard outside for about 10 
seconds to notify the driver that the key is 
in the boot. In this case, take out the key 
by pressing the electric boot lid opener 
and opening the boot lid. The key taken 
out of the boot may not operate because its 
functions have been temporarily stopped. 
To restore the key's functions, perform the 
applicable procedure (page  3-8 ).
 Key Left-in-vehicle Warning Beep 
(With the advanced keyless 
function)
              If  all  the  doors  and  boot  are  locked  using 
another key while the key is left in the 
cabin, the beep which sounds outside of 
the vehicle will be heard for about 10 
seconds to notify the driver that the key 
is in the cabin. In this case, take out the 
key by opening the door. A key taken 
out of the vehicle using this method may 
not operate because its functions have 
been temporarily stopped. To restore the 
key's functions, perform the applicable 
procedure (page  3-8 ).
 Electronic Steering Lock Warning 
Beep
              The  warning  beep  operates  if  the  steering 
wheel is not unlocked after the push button 
start is pressed. (page  4-4 )
 i-stop  Warning  Beep *
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
     If the driver's door is opened while 
engine idling is stopped, the warning 
sound operates to notify the driver that 
engine idling is stopped. It stops when 
the driver's door is closed.
   
 
 
     The warning sound operates if the 
following operations are performed 
while the engine idling is stopped. In 
such cases, the engine does not restart 
automatically to ensure safety. Start the 
engine using the normal method.
   
 
    
 (European model) 
   The driver's seat belt is unfastened and 
the driver's door is opened.
   
 
    
 (Except European model)
 
 
 
    
 (Manual transmission) 
   With the shift lever in a position other 
than neutral, the driver's seat belt is 
unfastened and the driver's door is 
opened.
   
 
    
 (Automatic transmission) 
   With the selector lever in the D or 
M (not in second gear  ¿ xed mode) 
position, the driver's seat belt is 
unfastened and the driver's door is 
opened.
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 547 of 609
7–53
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Vehicle  Speed  Alarm *
              The  vehicle  speed  alarm  function  is 
designed to alarm the driver via a single 
beep sound and a warning indication in the 
instrument cluster that the previously set 
vehicle speed has been exceeded.
  You can change the vehicle speed setting 
at which the warning is triggered.
 120 km/h Warning Beep *
              If  the  vehicle  speed  exceeds  120  km/h,  a 
chime sounds for 5 seconds.
 Outside Temperature Warning 
Beep*
              Warns  the  driver  of  the  possibility  of  icy 
roads when the outside temperature is low.
  If the outside temperature is lower than 
about 4 °C (39 °F) , a beep sound is heard 
once and the outside temperature display 
 À ashes for about ten seconds.
  (Type  A  instrument  cluster)
  Refer to Outside Temperature Display on 
page 4-37 .
  (Type B instrument cluster)
  Refer to Outside Temperature Display on 
page 4-29 .
 Power Steering Warning Buzzer
              If  the  power  steering  system  has 
a malfunction, the power steering 
malfunction light turns on or  À ashes and 
the buzzer operates at the same time.
  Refer  to  Warning  Indication/Warning 
Lights on page  4-42 .
 Ty r e   I n À ation Pressure Warning 
Beep*
              Vehicle  with  conventional  tyres
    The warning beep sound will be heard 
for about 3 seconds when there is any 
abnormality in tyre in À ation pressures.
  Refer to Tyre Pressure Monitoring System 
(Vehicle with Conventional Tyres) on page 
 4-140 .
  Vehicle  with  run- À at tyres
    The warning beep sound will be heard 
for about 3 seconds if the tyre pressures 
decrease.
  If the tyre pressure decreases extremely, 
a beep sound will be heard for 
approximately 30 seconds.
  Refer to Tyre Pressure Monitoring System 
(Vehicle with Run- À at Tyres) on page 
 4-144 .
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 548 of 609
7–54
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
 Blind Spot Monitoring (BSM) 
System Warning Beep *
              D r i v i n g   f o r w a r d
    The warning beep operates when the 
direction indicator lever is operated to 
the side where the Blind Spot Monitoring 
(BSM) warning light is illuminated.
 NOTE
 A personalised function is available 
to change the Blind Spot Monitoring 
(BSM) warning beep sound volume. 
 Refer to Personalisation Features on 
page 9-10 . 
  Reversing
    If a moving object such as a vehicle or 
two-wheeled vehicle approaches on the 
left or right from behind your vehicle, the 
Blind Spot Monitoring (BSM) warning 
sound is activated.
 Lane Departure Warning Sound *
              While  the  system  is  operating,  if  the 
system determines that the vehicle may 
depart from the lane, it sounds a warning 
sound.
 NOTE
        The volume of the LDWS warning 
sound can be changed. 
   Refer to Personalisation Features on 
page 9-10 . 
        The type of the LDWS warning 
sound can be changed. 
   Refer to Personalisation Features on 
page 9-10 . 
 Speed Limiter Warning Beep *
              If  the  vehicle  speed  exceeds  the  set  speed 
by about 3 km/h (2 mph) or more, a 
warning beep operates continuously. The 
warning beep operates until the vehicle 
speed decreases to the set speed or less.
 CAUTION
 If the set speed is set lower than the 
current vehicle speed by pressing the 
SET  
  or RESUME/   switch, the 
warning beep is not activated for about 
30 seconds even if the vehicle speed is 
faster than the newly set speed by 
3 km/h (2 mph). Be careful not to drive 
over the set speed. 
 NOTE
 When the system is temporarily 
cancelled by depressing the accelerator 
pedal fully, the adjustable speed limiter 
display shows the cancel display. If the 
vehicle speed exceeds the set speed by 
about 3 km/h (2 mph) or more while the 
cancel display is displayed, the set speed 
display À ashes but the warning sound is 
not operated. 
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 549 of 609
7–55
If Trouble Arises
When Boot Lid Cannot be Opened
                When  Boot  Lid  Cannot  be 
Opened
    If the battery is dead, the boot cannot be 
unlocked and opened.
  In this case, the boot can be unlocked by 
taking care of the dead battery situation.
  Refer to Jump-Starting on page  7-20 .
  If the boot cannot be unlocked even 
if the dead battery situation has been 
resolved, the electrical system may have a 
malfunction.
  Soft  top  model
     1.   Close  the  convertible  top.
    Refer to Raising the Convertible Top 
on page  3-41 .
   2.   Remove  the  windblocker.
Windblocker
   3.   Remove the fasteners on the right side 
of the vehicle.
   4.   Partially peel back the cover on the 
right side of the vehicle.
   5.   Turn and loosen the cap screws until 
the screws start to spin free.
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D                           
Page 550 of 609
7–56
If Trouble Arises
When Boot Lid Cannot be Opened
   6.   Pull out the cap and open the boot lid.
    After performing this emergency 
measure, have the vehicle inspected at 
an expert repairer, we recommend an 
Authorised Mazda Repairer as soon as 
possible.
 CAUTION
 Do not pull the screw when pulling the 
cap. Otherwise, the screw may fall off 
and become lost. 
  Retractable  fastback  model
 CAUTION
 Do not touch the linkage and gears. If 
sharp edges and gears are touched, it 
could cause injury. 
  Roof  operates  electrically
    1.   Remove the aerial if it is installed. 
 Refer to Aerial on page  5-14 .
2.      Start  the  engine.
3.      Continue  pressing  the  retractable 
fastback switch in the open direction 
until the rear roof is completely open.
    Refer to Opening the Roof on page 
 3-51 .
Multi-information 
display indication
 NOTE
 Stop operating the switch before 
the front roof opens. If the switch is 
continuously pressed, the front roof 
opens and the following procedures 
cannot be performed. 
4.     Switch  the  ignition  OFF.
 / :   A  ( .   ' '    , A ' F K V K Q P   K P F D