alarm MAZDA MODEL MX-5 RF 2017 Owners Manual (in English)

3–55
Before Driving
Security System
*Some models.
Theft-Deterrent System *
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and À ashing the
hazard warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.
The intrusion sensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
 
 Do not hang clothing or objects from
a head restraint.
  Return the sunvisors to their original
positions.
  Do not blind the intrusion sensor by
covering it or placing objects over it.
  Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
  Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
  Do not install seats that are not
Mazda genuine products.
  To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

Intrusion sensor and
intrusion sensor bezel
/:A(.'',A'FKVKQPKPFD

3–56
Before Driving
Security System
Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently and
the hazard warning lights À ash for about
30 seconds when the system is triggered
by any one of the following:
 


 Unlocking a door with an inside door-
lock knob.
 


 Forcing open a door, the bonnet or the
boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
 


(With the intrusion sensor)
 The intrusion sensor detects a movement
in the vehicle.
The system will be triggered again (up to
10 times) if one of the above conditions
remains.
 


(With the intrusion sensor)
 Disconnecting the battery terminal (the
hazard warning lights do not À ash).
The system will be triggered about 10
times.
NOTE
  The boot lid does not open while the
theft-deterrent system is operating.
  If the battery goes dead while the
theft-deterrent system is armed,
the siren/horn will activate and the
hazard warning lights will À ash when
the battery is charged or replaced.
How to Arm the System
1. Close the windows and the convertible
top securely.
NOTE
(With the intrusion sensor)
The intrusion sensor function can be
armed only when the convertible top is
closed.
Even with a window open, the system
can be armed, however, leaving the
windows even partially open can invite
theft, and wind blowing into the vehicle
could trigger the alarm.
The intrusion sensor function can also
be cancelled.
Refer to Cancelling the Intrusion Sensor
(With Intrusion Sensor) on page 3-57 .
2. Switch the ignition OFF.
3. Make sure the bonnet, convertible top,
the doors, and the boot lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will À ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument cluster À ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
/:A(.'',A'FKVKQPKPFD

3–57
Before Driving
Security System
NOTE
  The theft-deterrent system can also
be armed by activating the auto
relock function with all the doors, the
boot lid and the bonnet closed.
 Refer to Transmitter on page 3-5 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door.



 Opening the bonnet.



 Switching the ignition ON.

 To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
À ash once to indicate that the system
is armed.
Cancelling the Intrusion Sensor
(With Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the intrusion
sensor to prevent the alarm from triggering
unnecessarily.
(Intrusion sensor)
 


 Leaving the vehicle with a movable
object, passengers or pets remaining
inside.
 


 Leaving an object inside the vehicle
that can roll around, such as when the
vehicle is placed on a tilting, unstable
surface when being shipped.
 


 Hanging small objects/accessories in the
vehicle, or placing other items which
can move easily inside the vehicle.
 


 Parking in an area where there is strong
vibration or loud noise.
 


 When using a high pressure or automatic
car wash.
 


 Continuous shock and vibration
from hail or thunder and lightning is
transmitted to the vehicle.
 


 Doors are locked with a window left
open.
 


 An accessory heater or device that
produces moving air and vibration
operates while the theft deterrent system
is armed.
NOTE
If any door or the boot lid remains
closed for 30 seconds, both doors and
the boot lid automatically re-lock and
the theft deterrent system arms even if
a window or the convertible top is left
open.
/:A(.'',A'FKVKQPKPFD

3–58
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will À ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.
The hazard warning lights will À ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will À ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric boot lid opener
while the key is being carried.
The hazard warning lights will À ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the console box.
Mazda recommends that you af¿ x it to the
lower rear corner of a front door window.
/:A(.'',A'FKVKQPKPFD

4–30
When Driving
Instrument Cluster and Display
*Some models.
Adjustable Speed Limiter Display
(Without Multi-information
Display)
*
The setting status of the adjustable speed
limiter is displayed.
Cruise Control Set Vehicle Speed
Display (Without Multi-
information Display)
*
The vehicle speed preset using the cruise
control is displayed.
(European model)
(Except European model)
Trip Computer and INFO Switch
(Without Multi-information
Display)
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
 


 Approximate distance you can travel on
the available fuel
 


 Average fuel economy



 Current fuel economy



 Average vehicle speed



 Vehicle speed alarm *
If you have any problems with your trip
computer, consult an expert repairer, we
recommend an Authorised Mazda Repairer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.
The distance-to-empty will be calculated
and displayed every second.
(European model)
(Except European model)
NOTE
  Even though the distance-to-empty
display may indicate a suf¿ cient
amount of remaining driving distance
before refuelling is required, refuel
as soon as possible if the fuel level
is very low or the low fuel warning
light illuminates.
  The display may not change unless
you add more than approximately 9 L
(2.3 US gal, 1.9 Imp gal) of fuel.
  The distance-to-empty is the
approximate remaining distance
the vehicle can be driven until all
the graduation marks in the fuel
gauge (indicating the remaining fuel
supply) disappear.
  If there is no past fuel economy
information such as after ¿ rst
purchasing your vehicle or the
information is deleted when the
battery leads are disconnected, the
actual distance-to empty/range may
differ from the amount indicated.
/:A(.'',A'FKVKQPKPFD

4–31
When Driving
Instrument Cluster and Display
*Some models.
Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total travelled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed every
minute.
(European model)
(Except European model)
To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - L/100
km (- - - mpg) will be displayed for about
1 minute before the fuel economy is
recalculated and displayed.
Current fuel economy mode
This mode displays the current fuel
economy by calculating the amount of fuel
consumption and the distance travelled.
Current fuel economy will be calculated
and displayed every 2 seconds.
(European model)
(Except European model)
When you've slowed to about 5 km/h (3
mph), - - - L/100 km (- - - mpg) will be
displayed.
Average vehicle speed mode
This mode displays the average vehicle
speed by calculating the distance and the
time travelled since connecting the battery
or resetting the data.
Average vehicle speed will be calculated
and displayed every 10 seconds.
(European model)
(Except European model)
To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch, - - - km/h
(- - - mph) will be displayed for about
1 minute before the vehicle speed is
recalculated and displayed.
Vehicle speed alarm mode
*
In this mode, the current setting for the
vehicle speed alarm is displayed. You can
change the vehicle speed setting at which
the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep
sound is heard. The set vehicle speed
À ashes several times.
The vehicle speed alarm can be set using
the INFO switch.
/:A(.'',A'FKVKQPKPFD

4–32
When Driving
Instrument Cluster and Display
NOTE
  Always set the vehicle speed
according to the laws and regulations
of the country/city in which the
vehicle is driven. In addition, always
verify the speed of the vehicle using
the speedometer.
  The vehicle speed alarm function can
be set between 30 and 250 km/h (20
and 150 mph).
The vehicle speed alarm can be set using
the following procedure.
1. Press the INFO switch to display the
vehicle speed alarm mode.
2. Press the INFO switch continuously
until a beep sound is heard.
The set vehicle speed display À ashes
the third digit (hundredths place).
3. Press the INFO switch and set the third
digit (hundredths place) to the desired
vehicle speed.
The numerical value changes each time
the INFO switch is pressed.
4. Press the INFO switch continuously
until a beep sound is heard.
The set vehicle speed display À ashes
the lower two digits (tenths and ones
place).
5. Press the INFO switch and set the two
lower digits (tenths and ones place) to
the desired vehicle speed.
The numerical value changes each time
the INFO switch is pressed. 6. Press the INFO switch continuously
until a beep sound is heard.
The set vehicle speed is displayed on
the vehicle speed alarm screen.
/:A(.'',A'FKVKQPKPFD

4–33
When Driving
Instrument Cluster and Display
*Some models.
Multi-information Display and INFO Switch *
INFO switch Multi-information Display
The multi-information display indicates the following information.
 


 Odometer



 Trip meter



 Engine coolant temperature gauge



 Fuel gauge



 Outside temperature



 Distance-to-empty



 Average fuel economy



 Current fuel economy



 Maintenance Monitor



 Lane Departure Warning System (LDWS) Display



 Cruise Control Display



 Adjustable Speed Limiter Display



 Compass Display



 Vehicle Speed Alarm



 Roof Operation Display



 Warning message
/:A(.'',A'FKVKQPKPFD

4–39
When Driving
Instrument Cluster and Display
*Some models.
Maintenance Monitor
The following maintenance period
noti¿ cations can be displayed by turning
the Maintenance Monitor on.
 


 Scheduled Maintenance



 Tyre Rotation



 Oil Change
For the setting method and indications
for the maintenance monitor, refer to the
Maintenance Monitor.
Refer to Maintenance Monitor on page
6-10 .
The maintenance monitor displays the
information when the ignition is switched
ON.
NOTE
This function is inoperable while the
vehicle is being driven.
Message display
When the remaining time or the distance
approaches 0, a message is displayed each
time the ignition is switched ON.
NOTE
  If any of the INFO switch is pressed
while a message is displayed, it will
no longer be displayed the next time
the ignition is switched ON.
  After the vehicle is serviced and the
remaining time/distance is reset, the
message for the next maintenance
period will be displayed when the
remaining distance or time to the
next maintenance period approaches
0 (displays when engine is started).
  If there are multiple messages, they
are displayed according to their
order.
  If OFF is set for Messages, messages
are not displayed.
Vehicle Speed Alarm *
In this mode, the current setting for the
vehicle speed alarm is displayed. You can
change the vehicle speed setting at which
the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep
sound is heard. The set vehicle speed
À ashes several times.
The vehicle speed alarm can be set using
the centre display.
/:A(.'',A'FKVKQPKPFD

4–40
When Driving
Instrument Cluster and Display
*Some models.
NOTE
  Always set the vehicle speed
according to the laws and regulations
of the country/city in which the
vehicle is driven. In addition, always
verify the speed of the vehicle using
the speedometer.
  The vehicle speed alarm function can
be set between 30 and 250 km/h (20
and 150 mph).
Lane Departure Warning System
(LDWS) Display *
Displays the system status.
Refer to Lane Departure Warning on page
4-111 .
Adjustable Speed Limiter Display *
The setting status of the adjustable speed
limiter is displayed.
Cruise Control Set Vehicle Speed
Display*
The vehicle speed preset using the cruise
control is displayed.
Compass Display
The direction the vehicle is moving is
displayed in one of the eight cardinal
directions while the vehicle is being
driven.
Display Direction
N North
S South
E East
W West
NE Northeast
NW Northwest
SE Southeast
SW Southwest
/:A(.'',A'FKVKQPKPFD