steering wheel MAZDA MODEL PROTÉGÉ 2002 (in English) User Guide

4-7
Before Driving Your Mazda
Driving Tips
Form No. 8Q36-EA-01F
When driving on ice or in water, snow,
mud, sand, or similar hazard:
•Be cautious and allow extra distance
for braking.
•Avoid sudden braking and quick
steering.
•If your vehicle is not equipped with
ABS, brake with the pedal by using a
light up-down motion. Don’t hold the
pedal down constantly.
If your vehicle is equipped with ABS,
don’t pump the brakes. Continue to
press down on the brake pedal.
•If you get stuck, shift to 1 or 2 and
accelerate slowly. Don’t spin the front
wheels.
•For more traction in starting, use sand,
rock salt, chains, carpeting, or other
nonslip material under the front
wheels.If you must rock the vehicle to free it from
snow, sand, or mud, depress the
accelerator slightly and slowly move the
shift lever back and forth from 1 (D) to R.
Hazardous Driving
Downshifting on Slippery Surfaces:
Downshifting into lower gear while
driving on slippery surfaces is
dangerous. The sudden change in tire
speed could cause the tires to skid.
This could lead to loss of vehicle
control and an accident. If it is
necessary to downshift on slippery
surfaces, be very careful.
NOTE
Use snow chains only on the front
wheels.
WARNING
Rocking the Vehicle
Spinning the Wheels:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tire could overheat and
explode. This could cause serious
injuries. Don’t spin the wheels at
more than 56 km/h (35 mph), and
don’t allow anyone to stand behind a
wheel when pushing the vehicle.
Too much rocking may cause engine
overheating, transaxle failure, and tire
damage.
WARNING
CAUTION
J39L(02MY).book Page 7 Thursday, November 1, 2001 10:49 AM

5-2
Driving Your Mazda
Form No. 8Q36-EA-01F
Starting and Driving

Ignition Switch Positions
LOCK
The steering wheel locks to protect
against theft. Only in this position can the
key be removed.
Manual transaxle
When turning the ignition switch to the
LOCK position, push the key in at the
ACC position.Automatic transaxle
When turning the ignition switch to the
LOCK position, keep the shift lever in P.
Ignition Switch
LOCK
Push the key ACCON
Removing the Key:
It’s dangerous to remove the key from
the ignition switch while the vehicle is
moving. Removing the key allows the
steering wheel to lock. You will lose
steering control and a serious
accident could occur.
Remove the key only when the vehicle
is parked.
Not Setting the Parking Brake:
Leaving the driver’s seat without
setting the parking brake is
dangerous. Unexpected vehicle
movement could occur if the parking
brake is not set. This could cause an
accident. Before leaving the driver’s
seat, always set the parking brake and
make sure the shift lever is in P with
an automatic transaxle or in 1 or R
with a manual transaxle.
LOCKShift lever
engaged in P
(park) ACCON
WARNING
J39L(02MY).book Page 2 Thursday, November 1, 2001 10:49 AM

5-3
Driving Your Mazda
Starting and Driving
Form No. 8Q36-EA-01F
ACC (Accessory)
The steering wheel unlocks and some
electrical accessories will operate.
ON
This is the normal running position after
the engine is started. The warning lights
(except brakes) should be inspected
before the engine is started (page 5-24).
START
The engine is started in this position. It
will crank until you release the key; then
it returns to the ON position. The brake
warning light can be checked after the
engine is started (page 5-24).

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when
any door is opened.1. Occupants should fasten their seat
belts.
2. Make sure the parking brake is on.
3. Depress the brake pedal.
4. (Manual transaxle)
Depress the clutch pedal all the way
and shift into neutral.
Keep the pedal depressed while
cranking the engine.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
If turning the key is difficult, jiggle the
steering wheel from side to side.
Starting the Engine
NOTE
Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of
radio noise.
NOTE
The starter will not operate if the
clutch pedal is not
pushed down all the
way.
NOTE
The starter will not operate if the shift
lever is not
in P or N.
J39L(02MY).book Page 3 Thursday, November 1, 2001 10:49 AM

5-13
Driving Your Mazda
Starting and Driving
Form No. 8Q36-EA-01F
Power steering is only operable when the
engine is running. If the engine is off or if
the power steering system is inoperable,
you can still steer, but it requires more
physical effort.
If the steering feels rigid during normal
driving, consult an Authorized Mazda
Dealer.With cruise control, you can set and
automatically maintain any speed of more
than about 40 km/h (25 mph).

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.
Power Steering
Never hold the steering wheel to the
extreme left or right for more than five
seconds with the engine running.
This could damage the power steering
system.
CAUTION
Cruise Control
Cruise Control Use:
Using cruise control in the following
conditions could cause you to lose
control of the vehicle:
•Heavy or unsteady traffic
•Slippery or winding roads
•Similar restrictions that require
inconsistent speed
Don’t use cruise control in these
situations.
WARNING
J39L(02MY).book Page 13 Thursday, November 1, 2001 10:49 AM

5-38
Driving Your Mazda
Switches and Controls
Form No. 8Q36-EA-01F
To sound the horn, press around the
mark of the steering wheel.The hazard warning lights should always
be used when you stop on or near a
roadway.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning switch and all
four turn signals will flash at once.
HornHazard Warning Flasher
NOTE
•The turn signals don’t work when
the hazard warning lights are on.
•Check local regulations about the
use of hazard warning lights while
the vehicle is being towed. They
may forbid it.
Hazard warning flasher switch
J39L(02MY).book Page 38 Thursday, November 1, 2001 10:49 AM

7-7
In Case of an Emergency
Flat Tire
Form No. 8Q36-EA-01F
If you have a flat tire, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tire.
Stopping in traffic or on the shoulder of a
busy road is dangerous.1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in reverse (R), and turn off
the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tire
(page 7-3).
6. Block the wheel diagonally opposite
the flat tire. When blocking a front
wheel, place the block in front of the
tire. When blocking a rear wheel, place
the block behind the tire.
Changing a Flat Tire
NOTE
If the following occurs while driving, it
could indicate a flat tire.
•Steering becomes difficult.
•The vehicle begins to vibrate
excessively.
•The vehicle pulls in one direction.
Jacking a Vehicle:
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a
jack.
Passenger in Vehicle Supported by a
Jack:
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury. Never allow anyone inside a
vehicle supported by jack.
WARNING
NOTE
Make sure the jack is well lubricated
before using it.
J39L(02MY).book Page 7 Thursday, November 1, 2001 10:49 AM

8-7
Maintenance and Care
Scheduled Maintenance
Form No. 8Q36-EA-01F
I
: Inspect: Inspect and clean, repair, adjust, or replace if necessary . R: Replace
L
: Lubricate T
: Tightenan
*5: If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, change the brake fluid annually.
*6: This is a full function check of electrical systems such as lights, wiper and washer systems (including wiper
blades), and power windows.
Maintenance
Interval
Maintenance
ItemNumber of months or km (miles), whichever comes first
Months 6 121824303642485460667278849096
×1000 Km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
(×1000 Miles) (6) (12) (18) (24) (30) (36) (42) (48) (54) (60) (66) (72) (78) (84) (90) (96)
E.G.R. system (if installed)IIIIIIII
Battery electrolyte level
and specific gravityIIIIIIII
Brake and clutch pedalsIIIIIIIIIIIIIIII
Brake lines, hoses and
connectionsIIIIIIII
Brake fluid*
5I I IRI I IRI I IRI I IR
Clutch fluidIIIIIIIIIIIIIIII
Parking brakeIIIIIIIIIIIIIIII
Power brake unit and hosesIIIIIIII
Disc brakesIIIIIIIIIIIIIIII
Drum brakesIIIIIIII
Power steering fluid and linesIIIIIIIIIIIIIIII
Steering operation and gear
housingIIIIIIII
Steering linkage, tie rod ends and
armsIIIIIIII
Manual transaxle oilRR
Automatic transaxle fluid levelIIII III
Automatic transaxle fluid
RRR
Front and rear suspension and
ball jointsIIII
Driveshaft dust bootsIIII
Exhaust system heat shieldsIIII
Wheel nutsTTTTTTTT
Bolts and nuts on chassis and
bodyTTTTTTTT
All electrical system
*6 IIIIIIII
Headlight alignmentIIIII
Body condition (for rust,
corrosion and perforation)Ins
pect annually
Tires
(including spare tire, with
inflation pressure adjustment)IIIIIIII
Hinges and catchesLLLLLLLL
Road testIIIIIIIIIIIIIIII
J39L(02MY).book Page 7 Thursday, November 1, 2001 10:49 AM

8-28
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Tire Rotation
To equalize tread wear, rotate the tires
every 6,000 km (3,750 miles)/*12,000 km
(7,500 miles), or sooner if irregular wear
develops. During rotation, inspect them
for correct balance.
*Canada
Also, inspect them for uneven wear and
damage. Abnormal wear is usually caused
by one or a combination of the following:
•Incorrect tire pressure
•Improper wheel alignment
•Out-of-balance wheel
•Severe braking
After rotation, bring all tire pressures to
specification (page 10-7) and inspect the
lug nuts for tightness.

Replacing a Tire
If a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
You may need to replace it before the
band is across the entire tread.
Rotate unidirectional tires and radial
tires that have an asymmetrical tread
pattern or studs only from front to rear,
not from side to side. Tire performance
will be weakened if rotated from side
to side.
Front
Do not include (TEMPORARY USE ONLY
spare tire) in rotation.
CAUTION
Worn Tires:
Driving with worn tires is dangerous.
Reduced braking, steering, and
traction could result in an accident.
Always use tires that are in good
condition.
WARNING
New tread Worn treadTread wear indicator
J39L(02MY).book Page 28 Thursday, November 1, 2001 10:49 AM

11-5
Index
Form No. 8Q36-EA-01F
R
Rear Window Washer ...................... 5-37
Rear Window Wiper
........................ 5-37
Rearview Mirror
............................... 3-25
Recreational Towing
........................ 7-20
Rocking the Vehicle
........................... 4-7
Roof Rack
........................................ 3-21
S
Safety Defects, Reporting ................ 9-14
Seat Belt System
Pretensioner and load limiting
.. 2-16
Seat belt precautions
................. 2-11
Seat Belt Systems
............................. 2-11
3-point type
............................... 2-14
Extender
.................................... 2-20
Pregnant women
....................... 2-12
Rear-center lap/shoulder
........... 2-18
Warning light/beep
................... 2-21
Seats
Front seats
................................... 2-2
Rear seat
...................................... 2-5
Service Publications
......................... 9-14
Spare Tire and Tool Storage
.............. 7-3
Specifications
................................... 10-4
Speedometer
..................................... 5-21
SRS Air Bags
Air bag system description
....... 2-40
Supplemental restraint systems
precautions
................................ 2-35
Warning light
............................ 2-45
Starting the Engine
............................. 5-3
Steering Wheel
................................. 3-24
Horn
.......................................... 5-38
Storage Compartments
..................... 6-39
Sunroof
............................................. 3-19
Sunshade
.......................................... 3-20
Sunvisors
.......................................... 6-35
T
Tachometer .......................................5-22
Temporary Spare Tire
......................8-29
Tiedown
Hook
..........................................7-19
Tires
Flat tire
........................................7-3
Inflation pressure
.......................8-27
Replacement
..............................8-28
Rotation
.....................................8-28
Snow tires
....................................4-8
Spare tire and tool storage
...........7-3
Specifications
............................10-7
Tire chains
...................................4-9
Uniform tire quality grading
system (UTQGS)
.......................9-12
Tool
....................................................7-3
Towing
Description
................................7-18
Emergency towing
....................7-18
Hook
..........................................7-19
Recreational towing
..................7-20
Trailer towing
............................4-11
Trailer Towing
..................................4-11
Trip Meter
........................................5-21
Trunk Lid
..........................................3-11
Trunk Light
......................................3-12
Trunk Release Handle
......................3-13
Turn and Lane-Change Signals
........5-34
V
Vanity Mirrors ..................................6-35
Vehicle Information Labels
..............10-2
J39L(02MY).book Page 5 Thursday, November 1, 2001 10:49 AM