light MAZDA MODEL PROTÉGÉ 2002 (in English) Manual PDF

8-36
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Replacing a Bulb (Interior)
Overhead light (Type B)
Map lights (Type B)Map lights (Type A)
Overhead light (Type A)
Overhead light (Type C)Luggage compartment light
(Hatchback)
J39L(02MY).book Page 36 Thursday, November 1, 2001 10:49 AM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Replacing a Bulb (Rear)
Rear bulb access
(Sedan)
To replace the turn signal light, brake
light/taillight, side-marker light or reverse
light bulb, the trunk end trim must be
removed and the inside cover must be
partially opened.
1. Pull the center section of the plastic
retainer and remove the retainers and
the trunk end trim.
2. Remove the inside cover’s plastic
retainers and partially open the inside
cover.(Hatchback)
To replace the turn signal light, brake
light/taillight or reverse light bulb, remove
the caps and the cover.
Jack cover
J39L(02MY).book Page 37 Thursday, November 1, 2001 10:49 AM

8-38
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
Brake lights/Taillights
Rear side-marker lights
Reverse lights
Taillights
Rear turn signal lights
High-mount brake light (Sedan) License plate lights
Trunk light (Sedan)
Sedan
Sedan
Hatchback
Hatchback Brake lights/Taillights
Rear turn signal lights
Reverse lights
Sedan
To replace the high-
mount brake light bulb,
contact an Authorized
Mazda Dealer.
J39L(02MY).book Page 38 Thursday, November 1, 2001 10:49 AM

8-39
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
Yo u r v e h i c l e’s electrical system is
protected by fuses.
If any lights, accessories, or controls don’t
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.

Fuse Replacement
If the electrical system doesn’t work, first
inspect fuses on the driver’s side.
1. Turn off the ignition switch and other
switches.
2. Open the fuse panel cover.3. Pull the fuse straight out with the fuse
puller provided on the fuse panel.
4. Inspect it and replace if it’s blown.
5. Push in a new fuse of the same rating,
and make sure it fits tightly. If it
doesn’t, have an Authorized Mazda
Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the RADIO circuit.
Fuses
Fuse panel cover
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Fuse puller
Normal Blown
CAUTION
J39L(02MY).book Page 39 Thursday, November 1, 2001 10:49 AM

8-40
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new
one of the same rating.
When replacing the 100A fuse:
1. Turn off the ignition switch.2. Remove the negative battery terminal.
3. Remove the A nuts.
4. Lift the fuse block and remove the B
bolts.
5. Replace the fuse with a new one of the
same rating.
6. Install in the reverse order of removal.
Ta b
Fuse block
cover
Normal Blown
100A fuse
A
A
A
B
A
B A
J39L(02MY).book Page 40 Thursday, November 1, 2001 10:49 AM

8-41
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 HEATER 40 A Heater
2 (ABS) 60 AAntilock brake
system, For
protection of
various circuits
3 IG KEY 60 AFor protection of
various circuits
4 (PTC) 30 A—
5 (GLOW) 40 A—
6—— —
7COOLING
FA N30 A Cooling fan
8 BTN 40 AInterior lights,
Power door lock
9 (AD FAN) 30 AAdditional
cooling fan for air
conditioner
10INJ OR
FIP30 AEngine control
unit
11 (A/C) 10 A Air conditionerDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
12 (ST.SIG) 10 A Starter signal
13 HORN 15 A Horn
14 HAZARD 15 AHazard warning
flashers
15 TAIL 15 A Taillights
16(HEAD
C/U)7.5 AFor protection of
various circuits
17 (FOG) 15 A—
18 (FOG) 15 A Fog lights
19 STOP 15 A Brake lights
20 HEAD-R 15 A Headlight-right
21 HEAD-L 15 A Headlight-left
22—— —
23 HEAD HI 15 A—
24 MAIN 100 AFor protection of
all circuits
J39L(02MY).book Page 41 Thursday, November 1, 2001 10:49 AM

8-42
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
Fuse panel (Driver’s side)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1(S/WRM) 15 AFor protection of
various circuits
2 (H/CLN) 20 AFor protection of
various circuits
3 (RADIO) 15 A Audio system
4 (A/C) 15 A Air conditioner
5 (R.WIPER) 10 AFor protection of
various circuits
6—— —
7—— —
8 ROOM 10 AInterior lights,
Trunk light,
Luggage
compartment light
9(MIRR
DEF)10 A—
10—— —
11(DOOR
LOCK)30 A Power door lock
12 (P/WIND) 30 A—DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
13 WIPER 20 AWindshield wiper
and washer
14 ENGINE 10 AEngine control
unit
15 METER 10 A Instrument cluster
16—— —
17 (P/WIND) 30 A Power windows
J39L(02MY).book Page 42 Thursday, November 1, 2001 10:49 AM

8-46
Maintenance and Care
Appearance Care
Form No. 8Q36-EA-01F
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
Wa x i n g
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.

Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.

Bright-Metal Maintenance
•Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
•To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
•During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J39L(02MY).book Page 46 Thursday, November 1, 2001 10:49 AM

8-47
Maintenance and Care
Appearance Care
Form No. 8Q36-EA-01F

Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.

Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating. Don’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
NOTE
•Don’t use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
•Only use a mild soap or neutral
detergent and always use a sponge
or soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean
the wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
•Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
•If your aluminum wheels lose
luster, wax the wheels.
WARNING
J39L(02MY).book Page 47 Thursday, November 1, 2001 10:49 AM

10-7
Specifications
Form No. 8Q36-EA-01F

Light Bulbs

Tires
Standard tire
Temporary spare tire

Fuses
Refer to the fuse rating on page 8-39.
Light bulb Wattage
HeadlightsSedan 60/55
HatchbackHi 60
Lo 55
Front turn signal/Parking lights 27/8
Fog lights 55
Rear turn signal lights 21
Front side-marker lights 5
Rear side-marker lights (Sedan) 3.8
Taillights (Sedan) 3.8
Brake lights/Taillights 21/5
High-mount brake
lightSedanType A 21
Ty p e B 5 . 8
Hatchback 5.8
Reverse lights 21
License plate lights 5
Trunk light (Sedan) 5
Luggage compartment light (Hatchback) 5
Overhead lightType A 10
Type B and C 8
Map lights 5
Tire sizeInflation pressure
Front Rear
P185/65R14 85S
220 kPa (2.2 kgf/cm
2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
185/65R14 86T
210 kPa (2.1 kgf/cm2, 30 psi or lb/po2) 210 kPa (2.1 kgf/cm2, 30 psi or lb/po2)
P195/55R15 84V
220 kPa (2.2 kgf/cm2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
195/55R15 85V
210 kPa (2.1 kgf/cm2, 30 psi or lb/po2) 210 kPa (2.1 kgf/cm2, 30 psi or lb/po2)
P195/50R16 83V
220 kPa (2.2 kgf/cm2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
Tire size Inflation pressure
T125/70 D14
420 kPa (60 psi)
T115/70 D15
J39L(02MY).book Page 7 Thursday, November 1, 2001 10:49 AM