buttons MAZDA MODEL RX 8 2004 Owners Manual (in English)

3-27
Knowing Your Mazda
Steering Wheel and Mirrors
Form No. 8R65-EA-03C
Auto-dimming mirror*
The auto-dimming mirror automatically
reduces glare of headlights from cars at
the rear when the ignition switch is in the
ON position.
Press the OFF button ( ) to cancel the
automatic dimming function. The
indicator light will go off.
To reactivate the automatic dimming
function, press the ON button ( ). The
indicator light will illuminate.
OFF button
ON button
Indicator light
NOTE
•Do not use glass cleaner or suspend
objects on or around the light
sensor. Otherwise, light sensor
sensitivity will be affected and may
not operate normally.
•For information regarding the
3 buttons ( , , ) on the
auto-dimming mirror, refer to
HomeLink Wireless Control
System (page 5-55).
Light sensor
Light sensor
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 27 Saturday, April 26, 2003 1:48 PM

5-57
Driving Your Mazda
Switches and Controls
Form No. 8R65-EA-03C

Programming the HomeLink
System
The HomeLink system provides 3 buttons
which can be individually selected and
programmed using the transmitters for
current, on-market devices as follows:
1. Press and hold the two outer
HomeLink buttons (buttons one and
three) - releasing only when the
indicator light begins to flash (after 20
seconds). Do not
hold the buttons for
longer than 30 seconds and do not
repeat step 1
to program a second and/
or third hand-held transmitter to the
remaining two HomeLink buttons.
2. Position the end of your hand-held
transmitter 2.5—7.5 cm (1—3 inches)
away from the HomeLink button you
wish to program while keeping the
indicator light in view.
3. Simultaneously press and hold both the
chosen HomeLink and hand-held
transmitter buttons. Do not release the
buttons until step 4 has been
completed.4. After the HomeLink indicator light
changes from a slow to a rapidly
blinking light, release both the
HomeLink and hand-held transmitter
buttons.
5. Press and hold the just-trained
HomeLink button and observe the
indicator light.
If the indicator light stays on constantly,
programming is complete
and your
device should activate when the
HomeLink button is pressed and released.
If the indicator light blinks rapidly for
two seconds and then turns to a
constant light, continue with
"Programming" steps 6—8
to complete
the programming of a rolling code
equipped device (most commonly a
garage door opener).
6. At the garage door opener receiver
(motor-head unit) in the garage, locate
the "learn" or "smart" button. This can
usually be found where the hanging
antenna wire is attached to the motor-
head unit. When programming a garage door
opener or a gate, disconnect the power
to these devices before performing
programming, as continuous operation
of the devices could damage the motor.
NOTE
Some gate operators and garage door
openers may require you to replace this
Programming Step 3 with procedures
noted in the "Gate Operator/Canadian
Programming" section.
CAUTION
NOTE
If the HomeLink indicator light does
not change to a rapidly blinking light,
contact HomeLink at
www.homelink.com or call 1-800-355-
3515 for assistance.
NOTE
To program the remaining two
HomeLink buttons, begin with
"Programming" - step 2. Do not
repeat step 1.
J60E_8R65-EA-03C_Edition2.book Page 57 Saturday, April 26, 2003 1:48 PM

5-58
Driving Your Mazda
Switches and Controls
Form No. 8R65-EA-03C
7. Firmly press and release the "learn" or
"smart" button. (The name and color of
the button may vary by manufacturer.)
8. Return to the vehicle and firmly press,
hold for two seconds and release
the
programmed HomeLink button. Repeat
the "press/hold/release"
sequence a
second time, and, depending on the
brand of the garage door opener (or
other rolling code equipped device),
repeat this sequence a third time to
complete the programming process.
HomeLink should now activate your
rolling code equipped device.
For questions or comments, please contact
HomeLink at www.homelink.com or 1-
800-355-3515.
Gate operator/Canadian
Programming
Canadian radio-frequency laws require
transmitter signals to "time-out"(or quit)
after several seconds of transmission -
which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are
designed to "time-out" in the same
manner.
If you live in Canada or you are having
difficulties programming a gate operator
by using the "Programming" procedures
(regardless of where you live), replace
"Programming HomeLink" step 3
with
the following:
3. Continue to press and hold the
HomeLink button while you press and
release - every two seconds
("cycle")
your hand-held transmitter until the
frequency signal has successfully been
accepted by HomeLink. (The indicator
light will flash slowly and then
rapidly.)
Proceed with "Programming" step 4 to
complete.
NOTE
There are 30 seconds in which to
initiate step 8.
NOTE
To program the remaining two
HomeLink buttons, begin with
"Programming" - step 2. Do not
repeat step 1.
NOTE
If programming a garage door opener
or gate operator, it is advised to unplug
the device during the "cycling" process
to prevent possible overheating.
J60E_8R65-EA-03C_Edition2.book Page 58 Saturday, April 26, 2003 1:48 PM

5-59
Driving Your Mazda
Switches and Controls
Form No. 8R65-EA-03C

Operating the HomeLink System
Press the programmed HomeLink button
to operate a programmed device. The
code will continue being transmitted for a
maximum of 20 seconds.

Reprogramming the HomeLink
system
To program a device to HomeLink using a
HomeLink button previously trained,
follow these steps:
1. Press and hold the desired HomeLink
button. DO NOT
release the button.
2. The indicator light will begin to flash
after 20 seconds. Without releasing the
HomeLink button, proceed with
"Programming" - step 2.

Erasing Programmed HomeLink
Buttons
To erase the existing programming from
all three operating channels, press and
hold the two outside buttons ( , )
on the auto-dimming mirror until the
HomeLink indicator light begins to flash
after approximately 20 seconds.
Verify that the programming has been
erased when you resell the vehicle.
J60E_8R65-EA-03C_Edition2.book Page 59 Saturday, April 26, 2003 1:48 PM

6-22
Interior Comfort
Au di o S ys t em
Form No. 8R65-EA-03C

Operating the Radio
Radio ON
Press a band selector button ( , )
to turn the radio on.
Band selection
Choose AM by pressing the AM button
( ) and FM by pressing the FM1/2
button ( ).
The selected mode will be indicated. If
FM stereo is being received, "ST" will be
displayed.Tu n i n g
The radio has the following tuning
methods: Manual, Seek, Scan, Preset
channel, and Auto memory tuning. The
easiest way to tune stations is to set them
on preset channels.
Manual tuning dial/
Auto memory buttonChannel preset buttons
Scan button Band selector buttons
Seek
tuning
button
NOTE
If the FM broadcast signal becomes
weak, reception automatically changes
from STEREO to MONO for reduced
noise, and the "ST" indicator will go
out.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the preset channels will be canceled.
J60E_8R65-EA-03C_Edition2.book Page 22 Saturday, April 26, 2003 1:48 PM

6-30
Interior Comfort
Au di o S ys t em
Form No. 8R65-EA-03C

Operating the In-Dash CD Changer*
Inserting the CD
The CD must be label-side up when
inserting. The auto-loading mechanism
will set the CD and begin play. There will
be a short lapse before play begins while
the player reads the digital signals on the
CD.
The disc number and the track number
will be displayed.Normal insertion
1. Press the load button ( ).
2. When "IN" is displayed, insert the CD.
Inserting CDs into desired tray number
1. Press and hold the load button ( )
for about 2 seconds until a beep is
heard.
2. Press the channel preset button for the
desired tray number within 5 seconds
after the beep is heard.
3. When "IN" is displayed, insert the CD.
Scan
button Display button
Track up
button
Track down
button
Reverse button
Fast-forward
button
Random button Repeat button CD slot CD play button CD eject button
Load button
Disc down
button
Disc up buttonChannel preset buttons
NOTE
A CD cannot be inserted while the
display reads "WAIT". A beeping
sound can be heard during this waiting
time. Simultaneously pressing the
power/volume dial and the load button
( ) for about 2 seconds will turn
this beeping sound ON or OFF.
NOTE
The CD cannot be inserted to the
desired tray number if the number is
already occupied.
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 30 Saturday, April 26, 2003 1:48 PM

33
Open the
[System Setup]
screenVolume control for voice guidance (5 levels)
Beep

On : Beep activated when pressing buttons in the
remote control.

Off : Beep inactivated when pressing buttons in the
remote control.

On : Initiates vocal guidance.
Off : Initiates no vocal guidance.
Language
Changeover meter/mile

Metric : Meters
English : Miles
Voice repetition
Clock
Adjust the volume control at the monitor as well.
: Default
How to exit
Daylight Saving Time(Summer Time)

On : Daylight saving time mode is enabled.
(The navigation internal clock gains 1 hour).

Off : Daylight saving time mode is disabled.
SetupSystem
User setting
32
1
2select3
selectMENUENTER
ENTER
ENTER
ENTERENTER
ENTER
ENTER
ENTER
nt go back
om it.
atically
proaching
ute
ation.
fLifz

Sympto
No GPS sy
are display
The vehicle
position is
displayed
No voice gu
Buttons in
remote con
do not bee
No map disp(blank scre
38
There may be some problems due to operational errors or mistakes. Please read this
manual again and verify that there really is a problem before calling an Authorized Mazda
Dealer to ask for repair services.
SymptomCheck point


Check if a fuse has been blown.aConsult an Authorized Mazda Dealer.


Check if the voltage level of the vehicle battery is low.
aRecharge the battery or change batteries.


Check if the vehicle position changed when ACC was set to
OFF.
When, for example,
The vehicle was transported by a ferry boat.
The vehicle was rotated on a turn table in a parking lot.
The vehicle was transported by a tow track or other such
vehicle.
aDrive the vehicle for a while where you are receiving
GPS signals.
No picture
The vehicle
position is not
correct
Note
TroubleshootingVerification First
As necessary
37

39

GPS signals may not be received because of obstructions.
After removing the obstructions, the GPS signals can be
received.

Check if the mode is set to the map mode.
aPress

Check if the volume control for the voice guidance is
adjusted to zero.

Check if the vehicle is off the route.
Check if [Guidance Off] is selected.
aRepeat the route search while checking the route guide
screen.

Check if you are driving the vehicle in the wrong direction on
the route.
aRepeat the route search checking the direction of the
destination.

Check if [Beep] is set to [Off] ( page 33). ( page 25).

Check if the disc is wet, scratched, or dewy.
SymptomCheck point
No GPS symbols
are displayed
The vehicle
position is not
displayed
No voice guidance
Buttons in the
remote control
do not beep
No map displayed(blank screen)
As necessary
38
POS
d this
ed Mazda
low.
was set to
king lot.
her such
ceiving
First