MERCEDES-BENZ C-Class 2004 W203 Comand Manual

14 At a glanceQuick reference COMANDAt the multifunction steering wheel
To raise the volume
Press J.
To lower the volume

Press I.
At the COMAND operating unit

Turn the the left-hand rotary/push-
button v.
For the audio sources

Radio

CD (CD drive and CD changer)
you can set the volume jointly.For the service sources

Voice output during route guidance
(navigation system)
and

Voice Control System (refer to separa-
te operating instruction)
you can set the volume jointly.
For the service source

Telephone
you can alter the listening volume for the
telephone only.
Switching on

Press c.
The radio is switched on. The station
last tuned to will begin to play.
Changing the radio band

Press c to switch between FM-,
AM- and WB-Band.
Adjusting the volume
Radio operation
P82.85-6062-31

15 At a glance
Quick reference COMAND
Selecting a station
Automatic seek tuning
Press g or h on the rocker
switch briefly.
FM- and AM-Bands, Weather Band WB
The radio will tune in to the next recei-
vable station (FM/AM) or channel (WB)
with descending/ascending frequency.
Switching another system on

Press any system key, e.g. d.
COMAND will switch to CD mode.
You will find more information regarding
this topic in section “Radio operation” in
chapter “Audio” (
page 28).Switching on

Press d.
The main CD menu will appear.
Playback will begin in
CD drive with the first track on the
CD

CD changer* with the first track on
the first CD detected in the magazi-
ne.Loading a CD into the CD drive and loading
CDs in the CD changer (
page 45).
Track select

Press the rocker switch g/h.
You will hear the previous or next track.
If more than 9 seconds of playing time
have elapsed, the CD changes back to
the start of the current track.
Selecting a CD

Press one of the number keys
Key 0 select the CD drive
Keys 1 - 6 select the corresponding
magazine slot of the
CD changer
The message “Loading CD ...” appears
on the display. Playback then will begin
with track 1.
CD operation
P82.85-9063-31

16 At a glanceQuick reference COMANDCD track scan
Press the right-hand rotary/push-
button v to confirm “Scan”.
The tracks on the CD will be played one
after the other for 8 seconds each,
“Scan” will appear in red.

Press the right-hand rotary/push-
button v again to end the function.
Switching another system on

Press any system key, e.g a.
COMAND will switch to Telephone ope-
ration.
You will find more information in section
“CD operation” in chapter “Audio”
(
page 50).Switching on

Press W to switch to satellite radio
operation.
You will see the message “Aquiring sig-
nal. Please wait...”. After the COMAND
acquires the signal, the main satellite
radio menu will appear. The station last
tuned will begin to play.Selecting a station
Automatic tuning

Press g or h on the rocker
switch briefly.
The satellite radio will tune in the pre-
vious or next receivable station in the
selected category in alphabetical or-
der.
Manual category scan

Press g or h on the rocker
switch longer than 2 seconds.
You will hear a confirmation beep when
the function is active.

Repeatedly press g or h again
within 5 seconds until the desired cate-
gory appears.
Previous category
Press g.

Next category
Press h.
Satellite radio* operation

17 At a glance
Quick reference COMAND
The scan function ends:
automatically after 6 seconds
or
When you use the number keys 1 th-
rough 0 or t, u.
The first station (alphabetical order) of
the chosen category will begin to play.
You will see the corresponding catego-
ry and station name.
Switching another system on

Press any system key, e.g c.
COMAND will switch to normal radio
operation.
You will find more information in chapter
“Satellite radio” (
page 70).Switching on

Press a.
The menu to enter the unlock code will
appear.Entering the unlock code

Use the number keys 1 through 0 to
enter the unlock code.
Asterisks instead of digits will appear in
the input line.

Press the right-hand rotary/push-
button v to confirm the entry.
If entered code is correct and the pho-
ne is registered in a network, the phone
is ready for use.
Outgoing call
Enter a telephone number

Use the number keys 1 through 0 to
enter the telephone number.
The menu changes when the first digit
is entered.
Telephone* operation
P82.85-9064-31

18 At a glanceQuick reference COMANDBegin dialing
When the “Send” button is highlighted,
press the right-hand rotary/push-
button v to confirm your input.
Dialing will begin. If the phone number
together with a name is stored in the
phone book, the name appears on the
screen.
Conducting a call
When the call is answered, the call time ap-
pears in the screen.
Ending a call

Press the right-hand rotary/push-but-
ton v to confirm the “End” button.
Switching another system on

Press any system key, e.g. b.
COMAND switches to the navigation
system.
You will find more information in chapter
“Telephone” (
page 96).Switching the navigation system on
Main destination input menu

Press b.
If the navigation system has not been
booted up, the message “Navigation
being activated. Please obey all traffic
rules” will appear.
The navigation menu displayed will vary
according to the last navigation func-
tion used (
page 13).
If route guidance was switched off, the
main destination input menu will be
displayed.
Entering a destination and calcula-
ting a route
P82.85-9065-31

19 At a glance
Quick reference COMAND
Entering destination address
Press the right-hand rotary/push-
button v in the main destination input
menu and confirm “Address...”.
The main address menu will appear.
The entry behind “City...” is either
empty or the city you last entered will
appear.
“City/Suburb Entry” input menu
Press the right-hand rotary/push-but-
ton v in the main address menu and
confirm “City...”.
The “City/Suburb Entry” input menu
will appear.
Adopting the city last selected

Press the right-hand rotary/push-
button v longer than 2 seconds.Entering a city

Turn the right-hand rotary/push-
button v to highlight the first letter
and press to confirm.

Enter other characters until the desired
city appears in the input line.
Correcting entry

Last character
Press r briefly.

Complete entry
Press r longer than 2 seconds.
Activating the city list

Press the right-hand rotary/push-
button v longer than 2 seconds until
the city list appears.
P82.85-9066-31
P82.85-9067-31

20 At a glanceQuick reference COMANDCity list
Press the right-hand rotary/push-
button v again to confirm the city.
A selection menu will appear.

Press the right-hand rotary/push-
button v to confirm “Street…”.
The input menu “Street Entry” will ap-
pear.
The further sequence corresponds to the
“Entering a city” section.

Now enter the street and activate the
street list. Then confirm the street in
this list.You have now selected the destination and
can calculate the route.

Press the right-hand rotary/push-
button v to confirm “OK”.
The “Route Mode” selection menu will
appear.
iIf several options of a city/suburb are
available, another menu will appear
where you must make and confirm your
desired selection.
P82.85-9068-31
P82.85-9069-31

21 At a glance
Quick reference COMAND
“Route mode
” selection menu
Select a route and then a traffic route
Turn the right-hand rotary/push-
button v to move the cursor on the
entry you want and press to confirm.
A checkmark appears P.Route types available:

Fast Route

Short Route
Including P/avoiding traffic routes Q

Freeway

Ferry

Toll

Press the right-hand rotary/push-
button v to confirm “OK”.
The selected route and the destination
you have entered will appear on the
display.
You will hear the message “The route is
being calculated”.
Symbol displayAfter a few seconds, you will see the sym-
bol display.
CALC. ROUTE Calculation of route
2.9 miles Distance to destination
(as the crow flies)
P82.85-7484-31P82.85-9071-31
P82.85-9072-31

22 At a glanceQuick reference COMANDThe route will be calculated. COMAND
identifies the road you are travelling on.
You will see the arrow indicating the direc-
tion of travel if COMAND recognizes the
road you are travelling on. You will e.g.
hear the message “Please turn right”. Rou-
te guidance will begin.
You will find more information in chapter
“Navigation” (
page 161).Day and night display, switching off
screen

Press Ä repeatedly until the desired
display appears.
The display changes in this order: 
Day display

Night display

Screen off

Day displayYou can switch different beeps on and off.

Acknowledgement beep
Beeps when you accept an entry or en-
ter a destination on the map

Info beep
Beeps when you see the messages an-
nouncing a drop of battery voltage
(page 10)

Alarm beep
Beeps if the device has a serious mal-
function or if you are listening to an
emergency broadcast on the radio. You
can only switch off the beep if you also
switch off COMAND.
You will find more information in chapter
“System settings” (
page 215).
P82.85-9073-31
iIt is also possible to carry out the
change between day and night display
automatically via the headlight switch
(page 216).
Selecting beeps

23 Audio
Radio operation
CD operation
Sound settings