display MERCEDES-BENZ C-Class 2008 W204 Comand Manual

168 System settings
System settings
Once the first part is over, you will be
prompted to confirm that you wish to
start the second part.

Select “Yes” or “No”.
If you select “No”, the individualization
is cancelled. The data from the first
part is saved automatically.
If you select “Yes”, the second part of
the individualization will start.
The individualization is ended once the
second part has been completed. A corre-
sponding message is displayed. The data
from the second part is saved automatical-
ly.Cancelling first or second part of indi-
vidualization process

Select “Cancel”.
You will be prompted to confirm that
you really wish to cancel.

Select “Yes” or “No”.
If you select “Yes”, the individualization
is cancelled. The data from the can-
celled part will be lost.
If you select “No”, the cancelled part of
the individualization will restart.
Deleting any previous individualization
data

Select “System” K “System Settings”
K “Voice Control” K “Delete Individu-
alization”.
You will be prompted to confirm that
you really wish to delete it.

Select “Yes” or “No”.
The individualization data will be delet-
ed or retained on the basis of the selec-
tion. A corresponding message is
displayed.Switching individualization on/off

Select “System” K “System Settings”
K “Voice Control” K “Individualization
On”.
This switches the individualization on
D or off C.

169 System settings
System settings
General information on Bluetooth®
Bluetooth® is a technology for wireless
data communication over short distances
of up to approx. 30 feet. Using Bluetooth
®
you can exchange business cards (vCards),
for example.
Switching Bluetooth® on/off

Select “System” K “System Settings”
K “Bluetooth” K “Activate Bluetooth”.
This switches Bluetooth
® on D or
off C.
Connecting Bluetooth® devices
i In order to connect Bluetooth® devices,
Bluetooth® must be activated on the COMAND
and on the particular device. In addition, a Blue-
tooth
® device must be ‘visible’ for COMAND, so
that COMAND can find it and display it. The pro-
cedure for performing this setting is given in the
manual for the Bluetooth
® device.
The following types of devices can be con-
nected to COMAND via Bluetooth®:
Mobile phone
Portable personal computer
Laptop/PDA
You can connect a maximum of 10 devices
to COMAND.
The connection process includes search-
ing for a device and then authorizing it.
Opening the Bluetooth
® device list and
searching for a device

To open the list: Select “System” K
“System Settings”
K “Bluetooth” K
“Bluetooth Device List”.

To start search: Select “Update”.
COMAND starts searching for devices
in the reception range. After a short
time, the device list appears.
i If you open the device list again, the list of
authorized devices appears.

To cancel search: Select “Cancel”.
The device list may contain the following
devices:
All (available) devices found, regardless
of whether they have been authorized
or not.
All authorized devices, regardless of
whether they have been found (are
available) or not.When first entering the device list and be-
fore running an update, the black
dotRindicates the active phone (found
and authorized).
After running an update:
Phone icons 3 indicate if a phone is found
(black) or not (grey).
The check marks 1 indicate if a phone
has been authorized (black) or not (grey).
If a phone is not in the vehicle but has been
authorized previously, the phone symbol
and the check mark are grey 2.
Bluetooth® settings


170 System settings
System settings
i If the device list already contains ten autho-
rized devices, you will have to withdraw the au-
thorization for (de-authorize) one of the
authorized devices. You will then have to switch
this device off and start the search again. Other-
wise the new device you are looking for will not
appear in the list.
i If you reopen the device list at a later time,
this will contain all previously authorized devic-
es.
Displaying details on a Bluetooth®
device

Open the Bluetooth® device list
(
page 169).

Select the desired device.

Select “Options” K “Details”.
The details screen for the device is dis-
played.

To close details screen: Rotate ymz
or slide qmr.
Authorizing a Bluetooth® device

Open the Bluetooth® device list
(
page 169).

Select “Update”.
i If the authorization of a device, which had
been authorized in the past, has been withdrawn
and it is no longer found in the search, the device
list no longer includes this device.
Devices that have been authorized in the past
but not found in the search are either not
switched on or are not in the vehicle.

Select the as yet unauthorized device
(no check mark yet).

Select “Options” K “Authorize”.
The input menu for the passcode ap-
pears.
i The passcode is any number with between
one and sixteen digits that you can select your-
self. You must enter the same number on CO-
MAND and on the device to be authorized.
Please also refer to the instructions in the mobile
phone’s manual.

To enter passcode on COMAND:
Select digits one after another.

To cancel entry on COMAND: Select
“Back”.

To confirm entry on COMAND: Select
B:

Enter the same passcode on the Blue-
tooth® device (operating manual for
the relevant device).
The device is authorized.
De-authorizing a Bluetooth® device

Open the Bluetooth® device list
(
page 169).

Select the authorized device.

Select “Options” K “De-Authorize”.
You will be asked whether the device
should really be de-authorized.

Select “Yes” or “No”.
After selecting “Yes”, the authorization
of the device is withdrawn.

171 System settings
System settings
i You can fully reset COMAND to the factory
settings. This process deletes all personal data,
among other things, (e. g. station memory, ad-
dress book entries, entries in the destination
memory and in the last destinations of the navi-
gation system). It is recommended that you per-
form a reset before the vehicle is handed over or
sold, for example.

Select “System” K “System Settings”
K “Reset”.
You will be prompted to confirm that
you wish to perform the reset.

Select “Yes” or “No”.
After selecting “Yes”, you will again be
prompted to confirm that you wish to
perform the reset.

Select “Yes” or “No”.
After selecting “Yes”, COMAND is reset
and restarted.

Select “System” K “Language”.
The language list appears.
The dotRindicates the current setting.

To change setting: Select the desired
language.
The language is set.
i Setting the system language also changes
the language of the multifunction display.
ResetSetting the system language

172 System settings
Tele Aid*
The Tele Aid* system
(Tele Aid – Telematic Alarm Identification
on Demand)
The Tele Aid* system consists of three
types of response:
automatic and manual emergency
Roadside Assistance
Information
Automatically
An emergency call is initiated automatical-
ly following an accident in which the emer-
gency tensioning devices (ETDs) or air
bags deploy.
Initiating an emergency call manually
The SOS button is located in the overhead
control panel.

Briefly press SOS button cover to open.

Press SOS button (for longer than
2 seconds).
The indicator lamp in the SOS button
will flash until the emergency call is
concluded.

Wait for a voice connection to the Re-
sponse Center.

Close cover after the emergency call is
concluded.
i During the emergency call message “Emer-
gency Call Activated” is displayed, operation
from COMAND is not possible.
For a complete description and additional
information on Emergency calls please re-
fer to the vehicle Operator's Manual.
Tele Aid*Emergency calls

176 Voice Control
Overview
The following symbols indicate:
sthat you have to say something
tthat there is a voice output from the
voice control
uthat the system shows information
on the display.
You can use the voice control system to
operate the following systems depending
on the equipment in your vehicle:

Phone

Navigation

Address book

Audio (radio, satellite radio*,
DVD changer, memory card,
music register)
Say the commands without pausing
between individual words. If you enter a
command that does not exist or is incor-
rect, the voice control system asks you for
a new command with “Please repeat” or
“Please repeat your entry!”.
Overview
Operating Safety
G Warning
Please devote your attention first and fore-
most to the traffic situation you are in. While
the system permits hands-free phone oper-
ation, attention to traffic may be diverted
not only by physical operation of a phone,
but also by the distraction of a phone con-
versation while driving. As such, for safety
reasons, we encourage the driver to stop the
vehicle in a safe place before answering or
placing a phone call.
For safety reasons, you should only select a
destination when the vehicle is stationary.
While the navigation system provides direc-
tional assistance, the driver must remain fo-
cused on safe driving behavior, especially
attention to traffic and street signs, and
should utilize the system’s audio cues while
driving.
The navigation system does not supply any
information on stop signs, yield signs, traffic
regulations or traffic safety rules. Their ob-
servance always remains in the driver’s per-
sonal responsibility. DVD maps do not cover
all areas nor all routes within an area.
Traffic regulations always have priority over
any route recommendations given.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 13.5 m) every second.
G Warning
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.
G Warning
Please do not use the Voice Control System
in an emergency, as the tone of your voice
may change in a stressful situation. This
could cause a delay in completing your
phone call in a timely manner. This could
distract you in an emergency situation and
cause you to be involved in an accident.
Symbols only used in this chapter
Usage

177 Voice Control
Overview
The voice control confirms important com-
mands to you and gives you instructions in
the event of incorrect entries.
Command types
Voice control distinguishes between the
following types of command:

Global commands:
These are commands which can be
called up at any time (e.g. help or
phone commands).

Local commands:
These are commands which are only
available for the active application (e.g.
“Enter destination” during navigation).
Active application
The local commands refer to the applica-
tion currently shown on the display and to
the audio source you are currently listen-
ing to.
For example, if you are listening to the ra-
dio while the navigation application is ac-
tive on the display, you can operate both
applications using voice control.To operate a different function using voice
control, you must first switch to that appli-
cation using the corresponding command.
Operation using the multi-function
steering wheel
i You can cancel the dialog with voice control
at any time.
Voice control is operational around half a
minute after COMAND is switched on.
Starting the dialog
Switch on the ignition (see the vehicle
Owner's Manual).
Press the ! button.
An acoustic signal confirms that the di-
alog has been started.
Give a command.
Interrupting the dialog
If a list appears on the display, you can use
the “Pause” command to interrupt the dia-
log. You can then select an entry using the
COMAND controller.
To resume the dialog with voice control,
press the ! button on the multifunction
steering wheel.
1!Activates voice control
2LCancels voice control
3ç Decreases the volume
æ Increases the volume
oMute

178 Voice Control
Overview
Canceling the dialog
Press the L button.
or
Say the command “Cancel” (except
when creating and storing voice tags,
navigation entries or during individual-
ization).
or
Press any button on COMAND.
Adjusting the volume
Start the dialog.
Give a command, e.g. “Help”.
Press the æ or ç button.
The volume increases or decreases
during voice output.
or
Set the volume for the voice output on
the volume control for COMAND.
Display messages
The audible help function can be supple-
mented by visual help on the display
(
page 167). If the help function is
switched on, the most important com-
mands that are currently possible appear
in the display when you start the dialog.
In the address book and navigation sys-
tem, a selection list is shown in the display
if voice control requires additional informa-
tion from you.
1Display
Entering numbers

Digits from “zero” to “nine” are permit-
ted.

Say the phone number in groups of
three to five digits.
Spell

The letters of the alphabet and the
numbers 0 - 9 are permitted.

Say the letters in groups of five to sev-
en letters.

Say each individual letter clearly.
i Using individualization, you can fine-tune
voice control to your own voice and thus improve
voice recognition. The process of individualiza-
tion is described in chapter “System Settings”
(
page 167).
i If you use individualization, it may impair
recognition of other users. Switch off individual-
ization if it makes recognition of other users
worse.

180 Voice Control
Phone operation
“Phone”
Use the “Phone” command to select the
phone application. Use this command if
you wish the digits entered to be shown on
the display.
“Help Phone”
Voice control has an extensive help func-
tion. Using the “Help Phone” command,
you can have all the essential commands
for the phone read out (
page 201).
“Enter PIN”
Use the “Enter PIN” command to input the
PIN code (Personal Identification Number)
for your phone. To do this, the phone must
be connected via Bluetooth. When you
have given the command, voice control
prompts you to enter the PIN code.
Say the PIN code in the form of a continu-
ous string of digits or as blocks of digits,
e.g. three to five digits.
Digits 0 to 9 are permitted. Voice control
repeats the digits it recognizes after each
block of digits (with a pause of approxi-mately half a second between each block
of digits) and waits for you to continue
speaking.
Example of dialog:
sEnter PIN
tPlease say the PIN code
sZero one three three
tZero one three three
sOkay
! The card is blocked if you enter the wrong
code three times in a row. Use the PUK (personal
unblocking key) to unblock the card.
You can only enter the unblocking code via
the phone keypad – see the phone operat-
ing instructions.
“Dial number”
You can use the “Dial number” command
to dial a phone number.
The digits 0 - 9 and the word “Plus” are per-
mitted.
“Plus” replaces the international dialing
code, e.g. “00”.
Say the phone number in the form of a con-
tinuous string of digits or as blocks of dig-
its, e.g. three to five digits.Voice control repeats the digits it recogniz-
es after each block of digits (with a pause
of about half a second between each block
of digits) and waits for you to continue
speaking.
Example of dialog:
sDial number
tPlease say the number
sZero one three zero
tZero one three three
sFive zero zero five
tFive zero zero five
sOkay
tDialing number.
i You can also dial the specified number if you
press the s button on the multi-function
steering wheel instead of the concluding com-
mand “Okay”.
Commands

183 Voice Control
Navigation
Navigation
G Warning
For safety reasons, you should only select a
destination when the vehicle is stationary.
While the navigation system provides direc-
tional assistance, the driver must remain fo-
cused on safe driving behavior, especially
attention to traffic and street signs, and
should utilize the system’s audio cues while
driving.
The navigation system does not supply any
information on stop signs, yield signs, traffic
regulations or traffic safety rules. Their ob-
servance always remains in the driver’ per-
sonal responsibility. DVD maps do not cover
all areas nor all routes within an area.
Traffic regulations always have priority over
any route recommendations given.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 13.5 m) every second.
G Warning
During route guidance, you will not receive
information on:

traffic lights

stop and yield signs

parking or stopping zones

one-way streets

narrow bridges, or

other traffic regulation data.
You should therefore always strictly observe
traffic regulations while driving. Drive care-
fully and always obey traffic laws and road
signs, even if they contradict navigation sys-
tem instructions.
G Warning
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.
G Warning
Please do not use the Voice Control System
in an emergency, as the tone of your voice
may change in a stressful situation. This
could cause a delay in completing your
phone call in a timely manner. This could
distract you in an emergency situation and
cause you to be involved in an accident.