remote start MERCEDES-BENZ CL-Class 2008 C216 Comand Manual

352 Controls in detailLocking and unlockingSmartKey
Your vehicle comes supplied with two
SmartKeys, each with remote control and
a removable mechanical key.
The SmartKey provides an extended oper-
ating range. To prevent theft, however, it is
advisable to only unlock the vehicle when
you are in close proximity to it.
The SmartKey centrally locks and unlocks,
when set to factory settings (
page 354):


the doors


the trunk


the fuel filler flap
SmartKey with remote control1‹ Lock button
2ŠOpening button for trunk
(
page 500)
3Mechanical key locking tab
4ŒUnlock button
5Battery check lamp
6ÂPanic button (
page 64)
!
To prevent possible malfunction, avoid ex-
posing the SmartKey to high levels of electro-
magnetic radiation.
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.Warning!
G
To prevent possible personal injury, always
keep hands and fingers away from the door
or trunk lid opening when closing a door or
the trunk. Be especially careful when small
children are around.
Before closing doors, make sure there is no
possibility of someone getting caught in a
door during closing.

356 Controls in detailLocking and unlockingSmartKey with KEYLESS-GO*
Vehicles equipped with KEYLESS-GO come
with two SmartKeys with KEYLESS-GO,
each with remote control and a removable
mechanical key.
The KEYLESS-GO function is integrated
into the SmartKey. On these vehicles, the
validity of the SmartKey with KEYLESS-GO
is checked every time you grasp an outside
door handle.
With the KEYLESS-GO function, you can
lock and unlock the vehicle without using
the remote control buttons on the
SmartKey and start the engine without in-
serting the SmartKey in the starter switch.If the SmartKey with KEYLESS-GO is valid,
your vehicle unlocks:


the doors


the trunk


the fuel filler flap
SmartKey with KEYLESS-GO1‹ Lock button
2ŠOpening button for trunk
(
page 500)
3Locking tab for mechanical key
4ΠUnlock button
5Battery check lamp
6ÂPanic button (
page 64)
!
To prevent possible malfunction, avoid ex-
posing the SmartKey with KEYLESS-GO to high
levels of electromagnetic radiation.
Warning!
G
When leaving the vehicle, always take the
SmartKey with KEYLESS-GO* with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
Children could start the vehicle with a valid
SmartKey with KEYLESS-GO left in the
vehicle or with the KEYLESS-GO button on
the starter switch, or could release the
electronic parking brake, thereby putting
themselves and others in danger. Switch off
the engine and take the SmartKey with
KEYLESS-GO with you even if you are only
leaving the vehicle for a short while.

502 Controls in detailTrunkClosing trunk from inside automatically
1Remote trunk opening/closing switch

Press and hold switch1 until the
trunk is closed.
The indicator lamp in the switch goes
out when the trunk is closed.
To interrupt the closing procedure:

Release switch1.Closing trunk from outside
automatically
Warning!
G
Maintain sight of trunk area while operating
door mounted switch. Monitor the closing
procedure carefully to make sure no one is
in danger of being injured.
To interrupt the closing procedure, release
the door mounted remote trunk open-
ing/closing switch.
Even with the SmartKey or SmartKey with
KEYLESS-GO* removed from the starter
switch or the SmartKey with KEYLESS-GO*
removed from the vehicle, the remote trunk
opening/closing switch can be operated.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.
i
If the trunk lid comes into contact with an
object while closing (e.g. luggage that has been
piled too high) in the upper motion sequence, the
closing procedure is stopped and the trunk re-
opens slightly.
i
You can also close the trunk by hand.
Warning!
G
Monitor the closing procedure carefully to
make sure no one is in danger of being in-
jured. To prevent possible personal injury,
always keep hands and fingers away from
the trunk lid opening when closing the trunk.
Be especially careful when small children
are around. To stop the closing procedure,
do one of the following:

press button Š on the SmartKey or
SmartKey with KEYLESS-GO


press the trunk opening/closing switch
(on the driver’s door)


press the trunk closing switch


press the KEYLESS-GO locking/closing
switch*


pull the trunk lid handle

503 Controls in detailTrunk
Vehicles without KEYLESS-GO*1Trunk closing switch
Vehicles with KEYLESS-GO*1Trunk closing switch
Press trunk closing switch1 briefly.
The trunk closes.Closing trunk and locking vehicle from
outside (vehicles with KEYLESS-GO*)
You can close the trunk and lock the vehi-
cle simultaneously from the outside using
the KEYLESS-GO locking/closing switch.
1KEYLESS-GO locking/closing switch

Make sure you have the SmartKey with
KEYLESS-GO with you.

Press switch1 briefly.
Even with the SmartKey or SmartKey with
KEYLESS-GO* removed from the starter
switch or the SmartKey with KEYLESS-GO*
removed from the vehicle, the remote trunk
opening/closing switch can be operated.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child’s unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.
i
If the trunk lid comes into contact with an
object while closing (e.g. luggage that has been
piled too high) in the upper motion sequence, the
closing procedure is stopped and the trunk re-
opens slightly.
i
You can also close the trunk by hand.


532 Controls in detailUseful featuresProgramming integrated remote
control
Step 1:
Switch on the ignition (
page 365).
Step 2:

If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1 be-
gins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:

Hold the end of hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.
Indicator lamp1 will flash, first slowly
and then rapidly.Step 5:

After indicator lamp1 changes from a
slow to a rapidly flashing light, release
the hand-held remote control button
and the signal transmitter button.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe indicator lamp1.
If indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and
released.
i
Indicator lamp1 flashes immediately the
first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.

534 Controls in detailUseful featuresIf you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, indi-
cator lamp1 will flash slowly and then
rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 365).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

Indicator lamp1 will begin to flash af-
ter 20 seconds. Without releasing the
signal transmitter button, proceed with
programming starting with step 3.Operation of integrated remote control

Switch on the ignition (
page 365).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing integrated remote control
memory

Switch on the ignition (
page 365).

Simultaneously press and hold outer
signal transmitter buttons2 and 4,
for approximately 20 seconds, until
indicator lamp1 flashes rapidly. Do
not hold for longer than 30 seconds.
The codes of all three channels are
erased.
i
Upon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.
i
If you sell your vehicle, erase the codes of all
three channels.

749 Index
Loading (COMAND) 116
Playback options (COMAND) 124
Selecting a medium (COMAND) 122
Selecting a track (COMAND) 122
Setting the audio format
(COMAND) 124
Video (COMAND) 128
E
Easy-entry/exit feature 373
COMAND menu 264
EBP 70
Electrical fuses see Fuses
Electrical system, Technical Data 731
Electronic Brake Proportioning see EBP
Electronic parking brake 412
Indicator lamp 31, 610
Messages in display 646
Warning lamp 31, 610
Electronic Stability Program see ESP
®
Electronic traction system 72
Emergency call system 522
Emergency calls, Tele Aid 523
Emergency engine shut-down 717
Emergency operation
(Limp-Home Mode) 433Emergency operations
Locking the vehicle 684
Releasing from inside 504
Remote door lock 529
Remote door unlock 529
Unlocking the trunk 685
Unlocking the vehicle 684
Emergency Tensioning Device see ETD
Emergency, In case of
Battery, Jump starting 707
First aid kit 681
Flat tire 696
Fuses 714
Roadside Assistance 16
Roadside Assistance (Tele Aid) 525
Towing the vehicle 710
Emission control 548
Emission control information label 723
Emission control system warranties 14
Engine
Belt layout 724
Cleaning 597
Compartment 553
Coolant 559, 735, 738
Malfunction indicator lamp 31, 612Number 722, 723
Oil 557, 733, 736
Oils 554
Residual heat and ventilation 498
Starting 406
Technical data 725
Turning off 415
Engine coolant see Coolant
Engine oil 554
Adding 557
Additives 736
Checking level 554
Checking level (Dipstick) 557
Checking level (Instrument cluster
control system) 555
Consumption 554
Dipstick 557
Filler neck 557, 558
Messages in display 556, 670
Recommended engine oils and oil
filters 733
ESP
®
70
Messages in display 641, 652
Warning lamp 31, 609, 614

752 IndexI
Identification labels 722
Identification Number, Vehicle (VIN) 723
Ignition 365, 367
Switching on 365
Switching on, KEYLESS-GO* 367
Immobilizer 79
Indicator lamps see Lamps,
indicator and warning
Individualization
Voice Control 350
Infant and child restraint systems see
Children in the vehicle
Infrared reflecting windshield 536
Inside door handle 362
Instrument cluster 30, 434
Coolant temperature gauge 31, 435
Fuel gauge 31
Illumination 434, 483
Lamps 608
Multifunction display 282
Outside temperature indicator 436
Selecting the language
(COMAND) 258Interior lighting 398
Activating automatic control 398
Ambient lighting (COMAND) 265
Deactivating automatic control 398
Delayed switch-off (COMAND) 266
Reading lamps in the front 399
Interior rear view mirror
Adjusting 381
Auto-dimming 383
Interior storage spaces see
Storage compartments
J
Jack 682, 697
Jacking up the vehicle 697
Jump starting 707K
Key, Mechanical 684
Loss of 361
Key, SmartKey 352
Battery check lamp 352, 355
Factory setting 354
Global locking and unlocking 354
Lock button 352
Locking and unlocking 352
Loss of 361
Messages in display 662
Opening button for trunk 352
Panic button 64
Remote control 352
Restoring to factory setting 355
Selective setting 355
Starting the engine 407
Switching on ignition with 365
Turning off engine 415
Unlock button 352
Key, SmartKey with KEYLESS-GO* 356
Battery check lamp 356, 360
Factory setting 359
Global locking and unlocking 360
Important notes on using
KEYLESS-GO* 358

753 Index
Lock button 356
Locking and unlocking 356
Loss of 361
Messages in display 661
Opening button for trunk 356
Panic button 64
Remote control 356
Restoring to factory setting 361
Selective setting 360
Starting the engine 407
Switching on ignition with 367
Turning off engine 415
Unlock button 356
Kickdown 424
Kilopascal 586
Knee bag 46L
Labels 722
Certification 722
Emission control information 723
Tire and Loading Information 565
Vacuum line routing diagram 723
Lamp bulbs, exterior 688
Lamps, exterior
Front 689
Light sensor 664
Rear 689
Lamps, indicator and warning
ABS 31, 65, 608
Air bag Off 46
Battery check lamp (SmartKey with
KEYLESS-GO*) 360
Battery check lamp (SmartKey) 355
Brake warning lamp 31
Brakes 609
Combination low tire pressure
malfunction telltale 31, 618
Distance warning lamp* 31, 614
DISTRONIC Plus* 31, 446, 614
Electronic parking brake 31, 610
Engine diagnostics 31, 612Engine malfunction 31, 612
ESP
®
31, 609, 614
Front passenger
front air bag off 51, 620
High beam headlamp 31
Maintenance service indicator 592
Park Assist* 31
Parktronic* 31
Seat belt telltale 31, 615
SRS 31, 617
TPMS malfunction telltale 31, 618
Turn signals 31
Language (COMAND) 258
LATCH-type child seat anchors see
Children in the vehicle
Lever
For automatic transmission
(gear selector lever) 417
For cruise control 438, 449
For DISTRONIC Plus* 449
License plate lamps
Messages in display 666
Replacing bulbs 689
Light alloy wheels, Cleaning 604
Light sensor
Message in display 664

758 IndexProgram mode selector switch
Automatic shift program 427
Proper use of the vehicle 20
PSI 587
Push-start see Tow-start
R
RACETIMER see Control system
instrument cluster menus, AMG
Radio
FM/AM operation (COMAND) 98
Saving stations, FM/AM
(COMAND) 102
Selecting satellite radio channel
(Instrument cluster control
system) 290
Selecting stations 289
Submenu overview, FM/AM
(COMAND) 98
Switching wavebands, FM/AM
(COMAND) 99
Tuning in stations/channels 99
Voice Control 329
Radio transmitters, control and
operation 547
Range (distance to empty) 287Reading lamps in the front 399
Real-time traffic (COMAND) 244
Rear fog lamp
Replacing bulbs 689
Rear lamps see Tail lamps
Rear seats
Adjustment 368
Folding back and placing upright
rear head restraints 377
Head restraints 376
Ventilation* 376
Rear side windows
Blocking operation 63
Rear View Camera* 477
Camera lens 478
Cleaning camera lens 602
Switching on 480
View through the camera 478
Rear view mirrors see Mirrors
Rear window defroster 496
Activating 496
Deactivating 496
Recommended inflation pressure 587
Recovery services, Stolen vehicle
(Tele Aid) 530Refrigerant, Air conditioning 735, 736
Refueling 550
Regular checks 552
Remote
Door lock with Tele Aid 529
Door unlock with Tele Aid 529
Remote control, SmartKey 352
Remote control, SmartKey with
KEYLESS-GO* 356
Replacing
Bulbs 688
Front lamp bulbs 691
Rear lamp bulbs 689
Reporting safety defects 22
Reset (COMAND) 259
Residual engine heat and ventilation 498
Restraint systems
Messages in display 673
See Children in the vehicle
See SRS
Reverse gear position, Automatic
transmission 417, 421
Rims 587
And Tires 727
Tires and wheels 561