MERCEDES-BENZ CLA SHOOTING BRAKE 2022 Owners Manual

Overview of the bulbs to be changed
Halogen headlamps
1
High beam: H7 55 W bulb
2 Low beam: H7 55 W bulb Tail lamps
1
Turn signal light: PY 21 W bulb Changing the front bulbs (vehicles with halogen
headlam ps) Fitting/removing the cover in the front wheel arch
R
equirements:
= The lighting system is switched oM.
= The appropriate front wheel is turned inwards. 148
Light and sight


To remove: tur n cover 1 to the les and
remove it from the wheel arch liner. 
To Nt: inser
t cover 1 into the wheel arch liner
and turn it to the right until it engages.
Replacing illuminants in the halogen headlamp
R
equirements:
= Low beam: an H7 55 W illuminant is available.
= High beam: an H7 55 W illuminant is available. 1
Low beam housing cover
2 High beam housing cover 
Switch the lighting system oM. 
Remove the cover in the front wheel arch
( pag

e 148). 
Turn the relevant housing cover anti-clockwise
and r

emove it. 
Turn the socket anti-clockwise and remove it. 
Pull the illuminant out of the socket. 
Insert the new illuminant into the socket such
t
hat the entire base of the illuminant is resting
on the bottom of the socket. 
Insert the socket and turn it clockwise. 
Position the housing cover and turn it clock-
wise. 
Replace the cover in the front wheel arch
( pag

e 148). Changing the rear bulbs (vehicles with halogen
headlam
ps) Replacing the tail lamp illuminants

Due to their locations, have the illuminants for
t

he turn signal light and reversing light
changed at a qualiNed specialist workshop. Windscreen wipers and windscreen washer sys-
t
em Switching the windscreen wipers
on/oM 1
g W
indscreen wipers oM
2 Ä A
utomatic wiping, normal
3 Å A
utomatic wiping, frequent Light and sight
149

4
° Continuous wiping, slo w
5 ¯ Continuous wiping, f
ast
Turn the combination switch to the corre-
sponding position 1 - 5. 
Single wipe/washing: push t
he button on the
combination switch in the direction of arrow
1.
= í Single wipe
= î Wipes with washer Ouid
% Observe the notes on washing the vehicle in a
car w

ash ( page 349). Switching the rear window wiper
on/oM 1


Within around 15 seconds, press and hold the
î butt
on on the combination switch for
approximately three seconds (  page 149).
The wiper arms will move into the replacement
position.
Removing the wiper blades 
Fold the wiper arms away from the wind-
scr

een. 
Hold the wiper arm with one hand. With the
o

ther hand, turn the wiper blade away from
the wiper arm in the direction of arrow 1 as
far as it will go. 
Slide catch 2 in t
he direction of arrow 3
until it engages in the removal position. 
Remove the wiper blade from the wiper arm in
t

he direction of arrow 4. Fitting the wiper blades 
Insert the new wiper blade into the wiper arm
in t

he direction of arrow 1. 
Slide catch 2 in t
he direction of arrow 3
until it engages in the locking position. 
Make sure that the wiper blade is seated cor-
r

ectly. Light and sight
151


Fold the wiper arms back onto the wind-
scr een. 
Switch on the vehicle. 
Press the î butt
on on the combination
switch (  page 149).
The wiper arms will return to their original
positions. 
Switch oM t
he vehicle.
% Check the condition of the wiper blades regu-
lar

ly and replace them in the event of visible
damage or ongoing smearing. Maintenance display 
Remove protective Nlm 1 fr
om the mainte-
nance displays on the tips of the newly Ntted
wiper blades.
When the colour of the maintenance displays
c
hanges from black to yellow, replace the wiper
blades. %
The duration until the colour changes varies
depending on t

he usage conditions. Replacing the rear window wiper blade
&
WARNING Risk of becoming tr
apped if the
windscreen wipers are switched on while
wiper blades are being replaced
If the windscreen wipers begin to move while
y
ou are changing the wiper blades, you can be
trapped by the wiper arm. 
Always switch oM t
he windscreen wipers
and vehicle before changing the wiper
blades. Removing the wiper blade

Switch the vehicle oM.152
Light and sight


Fold wiper arm 2 a way from the rear window
until it engages in the replacement position. 
Unclip wiper blade 1 fr
om wiper arm 2 and
remove it in the direction of arrow 3.Fitting the wiper blade

Position wiper blade 1 wit h both lugs 3 on
holder 2 on the wiper arm. 
Push wiper blade 1 in t
he direction of arrow
4 until it engages in holder 2. 
Make sure that wiper blade 1 is seat
ed cor-
rectly. 
Fold the wiper arm from the replacement posi-
tion bac

k onto the rear window. Mirrors
Operating the outside mirrors
&
WARNING Risk of accident due t
o adjust-
ing the vehicle settings while the vehicle is
in motion
You could lose control of the vehicle in the fol-
lo
wing situations in particular:
= if you adjust the driver's seat, the head
restraint, the steering wheel or the mirror
while the vehicle is in motion
= if you fasten your seat belt while the vehi-
cle is in motion 
Before starting the vehicle: in particular,
adjus

t the driver's seat, head restraint,
steering wheel and mirror, and fasten
your seat belt. Light and sight
153

&
WARNING Risk of accident due t o mis-
judgement of distance when using the
outside mirror
The outside mirrors r
eOect objects on a
smaller scale. The objects in view are in fact
closer than they appear. 
Therefore, always look over your shoul-
der in or

der to ensure that you are aware
of the actual distance between you and
the road users driving behind you. 
To fold in or out: br
ieOy press button 2. 
To set: pr
ess button 1 or 3 to select the
outside mirror to be adjusted. 
Use button 4 t
o adjust the position of the
mirror glass.
% If the battery has been disconnected or com-
ple

tely discharged, you will have to reset the outside mirrors. Only then will the automatic
mir
ror folding function work properly. 
To reset: br
ieOy press button 2.
An outside mirror that has been pushed out of
position can be eng aged in position again as fol-
lows: 
Vehicles without electrically folding outside
mir

rors: manually move the outside mirror into
the correct position. 
Vehicles with electrically folding outside mir-
r
ors : press and hold button 2.
You will hear a click and the mirror will audibly
click into place. The outside mirror will now be
set to the correct position. Automatic anti-dazzle mirrors function
&
WARNING Risk of acid bur
ns and poison-
ing due to the anti-dazzle mirror electro-
lyte
Electrolyte may escape if the glass in an auto-
matic anti-dazzle mir
ror breaks.154
Light and sight

The electrolyte is hazardous to health and cau-
ses ir
ritation. It must not come into contact
with your skin, eyes, respiratory organs or
clothing or be swallowed. 
If you come into contact with electrolyte,
obser
ve the following:
= Immediately rinse the electrolyte
from your skin with water and seek
medical attention.
= If electrolyte comes into contact with
your eyes, immediately rinse them
thoroughly with clean water and seek
medical attention.
= If the electrolyte is swallowed, imme-
diately rinse your mouth out thor-
oughly. Do not induce vomiting. Seek
medical attention immediately.
= Immediately change out of clothing
which has been contaminated with
electrolyte.
= If an allergic reaction occurs, seek
medical attention immediately. The inside rearview mirror and the outside mirror
on t
he driver's side will automatically go into anti-
dazzle mode if light from a headlamp hits the sen-
sor on the inside rearview mirror.
System limits
The system will not go into anti-dazzle mode if:
= The vehicle is switched oM.
= Reverse gear is engaged.
= The interior lighting is switched on. Front-passenger outside mirror parking position
function
The parking position makes parking easier.
The fr
ont-passenger outside mirror will swivel
downwards in the direction of the rear wheel on
the front passenger's side when:
= the parking position is stored (  page 156).
= the front-passenger mirror is selected.
= reverse gear is engaged. The front-passenger outside mirror will move back
t

o its original position when:
= you shis the transmission to another transmis-
sion position.
= you are travelling at a speed greater than
15 km/h.
= you press the button for the outside mirror on
the driver's side. Light and sight
155

Storing the parking position of the front-
passeng
er outside mirror using reverse gear Storing

Press button 1 t
o select the front-passenger
outside mirror. 
Engage reverse gear. 
Move the front-passenger outside mirror into
t

he desired parking position using button 2.Calling up 
Press button 1 t
o select the front-passenger
outside mirror. 
Engage reverse gear.
The fr
ont-passenger outside mirror will move
into the stored parking position. Activating/deactivating the automatic mirror fold-
ing function
Multimedia system:
4 © 5
Settings 5
Vehicle 
Activate or deactivate Automatic fold-in.156
Light and sight

Overview of climate control systems
Notes on climate control
For the air-conditioning system, pollution level
monit
oring and air Nltration to function correctly,
an interior air Nlter must always be used. Make
sure that the Nlter is installed correctly. Use Nlters
recommended and approved by Mercedes-Benz.
Always have maintenance work carried out at a
qualiNed specialist workshop. Overview of the air conditioning control panel
The indicator lamps on the buttons indicate that
t
he corresponding function is activated. THERMATIC air conditioning control panel with sta-
tionar
y heater (example)
1 | Se
ts the temperature on the driver's
side
2 Vehicles with THERMATIC or THERMOTRONIC
oper
ating unit with stationary heater: &
calls up the air conditioning menu
Vehicles with THERMOTRONIC operating unit
wit
hout stationary heater: