MERCEDES-BENZ CLK63AMG 2007 A209 Owner's Manual
Page 351 of 505
350 Operation
Tires and wheels
Rotating tires
Tire rotation can be performed on vehicles 
with tires of the same dimension all 
around. If your vehicle is equipped with 
tires of the same dimension all around, 
tires can be rotated, observing a a 
front-to-rear rotation pattern that will 
maintain the intended rotation (spinning) 
direction of the tire (
page 326).
In some cases, such as when your vehicle 
is equipped with mixed-size tires (different 
tire dimension front vs. rear), tire rotation 
is not possible.If applicable to your vehicle’s tire configu-
ration, tires can be rotated according to 
the tire manufacturer’s recommended in-
tervals in the tire manufacturer’s warranty 
pamphlet located in your vehicle literature 
portfolio. If none is available, tires should 
be rotated every 3 000 to 6 000 miles 
(5 000 to 10 000 km), or sooner if neces-
sary, according to the degree of tire wear. 
The same rotation (spinning) direction 
must be maintained (
page 326). 
Rotate tires before the characteristic tire 
wear pattern becomes visible (shoulder 
wear on front tires and tread center wear 
on rear tires).
Thoroughly clean the mounting face of 
wheels and brake disks, i.e. the inner side 
of the wheels/tires, during each rotation. 
Check for and ensure proper tire inflation 
pressure.For information on wheel change, see the 
“Practical hints” section (
page 404) and 
(
page 436).
Warning!G
Rotate front and rear wheels only if the tires 
are of the same dimension.
If your vehicle is equipped with mixed-size 
tires (different tire dimensions front vs. 
rear), tire rotation is not possible.
Warning!G
Have the tightening torque checked after 
changing a wheel. Wheels could become 
loose if not tightened with a torque of 
80 lb-ft (110 Nm).
Only use Genuine Mercedes-Benz wheel 
bolts specified for your vehicle’s rims. 
Page 352 of 505
351 Operation
Winter driving
Winter driving
Before the onset of winter, have your 
vehicle winterized at an authorized 
Mercedes-Benz Center. This service 
includes:
Check of anticorrosion and antifreeze 
concentration.
Addition of cleaning concentrate to the 
water of the windshield and headlamp 
cleaning system. Add MB Concentrate 
“MB SummerFit” to a premixed wind-
shield washer solvent / antifreeze 
which is formulated for temperatures 
below freezing point (
page 479).
Battery test. Battery capacity drops 
with decreasing ambient temperature. 
A well charged battery helps to make 
sure that the engine can be started 
even at low ambient temperatures.
Tire change.
Winter tires
Always use winter tires at temperatures 
below 45°F (7°C) and whenever wintry 
road conditions prevail. Not all M+S rated 
tires provide special winter performance. 
Make sure the tires you use show the 
mountain/snowflake.marking on the 
tire sidewall. These tires meet specific 
snow traction performance requirements 
of the Rubber Manufacturers Association 
(RMA) and The Rubber Association of Can-
ada (RAC) and have been designed specif-
ically for use in snow conditions. Use of 
winter tires is the only way to achieve the 
maximum effectiveness of the ABS and the 
ESP
® in winter operation.
For safe handling, make sure that all 
mounted winter tires are of the same make 
and have the same tread design.Always observe the speed rating of the 
winter tires installed on your vehicle. If the 
maximum speed for which your tires are 
rated is below the speed rating of your ve-
hicle, you must place a notice to this effect 
where it will be seen by the driver. Such no-
tices are available at your tire dealer or any 
authorized Mercedes-Benz Center.
Warning!G
Winter tires with a tread depth under 1/6in 
(4 mm) must be replaced. They are no 
longer suitable for winter operation. 
Page 353 of 505
352 Operation
Winter driving
Block heater (Canada only)
The engine is equipped with a block 
heater.
The electrical cable may be installed at an 
authorized Mercedes-Benz Center.
Snow chains
Snow chains should only be driven on 
snow-covered roads at speeds not higher 
than 30 mph (50 km/h). Remove chains 
as soon as possible when driving on roads 
without snow.
Please observe the following guidelines 
when using snow chains:
Using snow chains is not permissible 
with all wheel/tire combinations 
(
page 466).
Use snow chains in pairs and on rear 
wheels only. Follow the manufacturer's 
mounting instructions.
Only use snow chains that are 
approved by Mercedes-Benz. Any 
authorized Mercedes-Benz Center will 
be glad to advise you on this subject.
Use of snow chains may be prohibited 
depending on location. Always check 
local and state laws before installing 
snow chains.
Do not use snow chains on the spare 
wheel (
page 469).
Warning!G
If you use your spare tire when winter tires 
are fitted on the other wheels, be aware that 
the difference in tire characteristics may 
very well impair turning stability and that 
overall driving stability may be reduced. 
Adapt your driving style accordingly.
Have the spare tire replaced with a winter 
tire at the nearest authorized 
Mercedes-Benz Center.!Some tire sizes do not leave adequate clear-
ance for snow chains. To help avoid serious dam-
age to your vehicle or tires, make sure that the 
use of snow chains is permissible as specified in 
the "Technical data" section of this Operator’s 
Manual, see “Rims and tires” (
page 466).
!If snow chains are mounted to the front 
wheels, they may scrape against the body or axle 
components. The tires or the vehicle could be 
damaged as a result.
iWhen driving with snow chains, you may 
wish to deactivate the ESP® (page 92) before 
setting the vehicle in motion. This will improve 
the vehicle‘s traction.
CLK 63 AMG:
Do not switch off the ESP
® when driving in snow 
or with snow chains mounted. 
Page 354 of 505
353 Operation
Maintenance
Maintenance
We strongly recommend that you have 
your vehicle serviced by an authorized 
Mercedes-Benz Center, in accordance with 
the Maintenance Booklet at the times 
called for by the maintenance service 
indicator.
Failure to have the vehicle maintained in 
accordance with the Maintenance Booklet 
and maintenance service indicator at the 
designated times /mileage will result in 
vehicle damage not covered by the 
Mercedes-Benz Limited Warranty.Maintenance service indicator 
message
The maintenance service indicator mes-
sage will notify you when your next mainte-
nance service is due.
Starting approximately 1 month before 
your next maintenance service is due, one 
of the following messages will appear in 
the multifunction display while you are 
driving or when you switch on the ignition 
(example service A):
Service A in XXXXX miles (km)
Service A in XXX days
Service A due now
The type of maintenance service due is 
indicated in the multifunction display:
9Basic service (A)
½Extended service (B)
iVehicles equipped with Maintenance 
System (U.S. vehicles. Canada vehicles, depend-
ing on vehicle production date):
The Maintenance System in your vehicle tracks 
distance driven and the time elapsed since your 
last maintenance service and calculates other 
maintenance service work required. 
Page 355 of 505
354 Operation
Maintenance
Clearing the maintenance service 
indicator message
The maintenance service indicator mes-
sage is automatically cleared after approx-
imately 30 seconds when you switch on 
the ignition or when reaching the mainte-
nance service threshold while driving.
You can also clear it yourself.
1Reset button
Press reset button 1 on the 
instrument cluster.The maintenance service indicator 
message is cleared and the standard 
display appears in the multifunction 
display (
page 145).
Maintenance service term exceeded
If you have exceeded the suggested 
maintenance service term, you will see the 
following message in the multifunction 
display:
Service A exceeded by XXXXX miles (km)
Service A exceeded by XXX days
In addition, a signal sounds when the 
message appears.
Any authorized Mercedes-Benz Center will 
reset the maintenance service indicator 
following a completed maintenance 
service.
iVehicles equipped with FSS (Flexible Ser-
vice S
ystem) only (Canada vehicles, depending 
on vehicle production date):
FSS evaluates engine temperature, oil level, 
vehicle speed, engine speed, distance driven 
and the time elapsed since your last service 
and calculates other maintenance service 
work required.
The interval between maintenance services 
depends on your driving habits. A gentle 
driving style, moderate engine speeds and 
the avoidance of short-distance trips will 
lengthen the interval between services. 
Page 356 of 505
355 Operation
Maintenance
Calling up the maintenance service 
indicator display
You can call up the maintenance service in-
dicator display at any time to check when 
the next maintenance service is due.
Switch on the ignition (page 38).
Press buttonè orÿ on the mul-
tifunction steering wheel repeatedly 
until the standard display appears in 
the multifunction display (
page 145).
Press buttonkorjuntil the 
maintenance service indicator display 
with the service symbol9or½ 
and the service deadline appears in the 
multifunction display.Resetting the maintenance service 
indicator 
In the event that the maintenance service 
on your vehicle is not carried out by an 
authorized Mercedes-Benz Center, you can 
have the maintenance service indicator 
reset. The automotive maintenance facility 
carrying out the maintenance service will 
find the information for resetting the 
maintenance service indicator in the 
maintenance-relevant information for your 
vehicle. Such information is available from 
either your authorized Mercedes-Benz 
Center or directly from Mercedes-Benz.iIf the battery is disconnected, the days of 
disconnection will not be included in the count 
shown by the maintenance service indicator. To 
arrive at the true maintenance service deadline, 
you will need to subtract these days from the 
days shown in the maintenance service indicator 
message or maintenance service indicator dis-
play.
Do not confuse the maintenance service indica-
tor with the engine oil level indicator:.
iIf the maintenance service indicator was in-
advertently reset, have an authorized 
Mercedes-Benz Center correct it.
Only reset if the proper maintenance service has 
been performed. Resetting the system without 
performing the proper service as called for by 
the maintenance service indicator will result in 
engine damage and/or other vehicle damage not 
covered by the Mercedes-Benz Limited Warran-
ty. 
Page 357 of 505
356 Operation
Vehicle care
Cleaning and care of vehicle
Regular and proper care will help to 
maintain the value of your vehicle. The 
best way to protect your vehicle from 
harmful environmental influences is to 
wash it and use protective treatments reg-
ularly.While in operation, even while parked, your 
vehicle is subject to varying external 
influences which, if gone unchecked, can 
attack the paintwork as well as the vehicle 
underbody and cause lasting damage.
Such damage is caused not only by 
extreme and varying climatic conditions, 
but also by:
Air pollution
Road salt
Tar
Gravel and stone chipping
To avoid paint damage, you should 
immediately remove:
Grease and oil
Fuel
Coolant
Brake fluid
Bird droppings
Insects
Tree resins, etc.Frequent washing reduces and / or 
eliminates the aggressiveness and 
potency of the above adverse influences.
More frequent washings are necessary to 
deal with unfavorable conditions:
near the ocean
in industrial areas (smoke, exhaust 
emissions)
during winter operation
You should check your vehicle from time to 
time for stone chipping or other damage. 
Any damage should be repaired as soon as 
possible to prevent corrosion.
In doing so, do not neglect the underbody 
of the vehicle. A prerequisite for a 
thorough check is a washing of the 
underbody followed by a thorough 
inspection. Damaged areas need to be 
re-undercoated. 
Your vehicle has been treated at the 
factory with a wax-base rustproofing in the 
body cavities which will last for the lifetime 
of the vehicle. Post-production treatment Warning!G
Many cleaning products can be hazardous. 
Some are poisonous, others are flammable. 
Always follow the instructions on the 
particular container. Always open your 
vehicle’s doors or windows when cleaning 
the inside.
Never use fluids or solvents that are not 
designed for cleaning your vehicle.
Always lock away cleaning products and 
keep them out of reach of children. 
Page 358 of 505
357 Operation
Vehicle care
is neither necessary nor recommended by 
Mercedes-Benz because of the possibility 
of incompatibility between materials used 
in the production process and others 
applied later.
We have selected car-care products and 
compiled recommendations which are 
specially matched to our vehicles and 
which always reflect the latest technology. 
You can obtain Mercedes-Benz approved 
car-care products at an authorized 
Mercedes-Benz Center.
Scratches, corrosive deposits, corrosion or 
damage due to negligent or incorrect care 
cannot always be removed or repaired with 
the car-care products recommended here. 
In such cases it is best to seek aid at an 
authorized Mercedes-Benz Center.
The following topics deal with the cleaning 
and care of your vehicle and give important 
“how-to” information as well as references 
to Mercedes-Benz approved car-care 
products.Power washer
Tar stains
Quickly remove tar stains before they dry 
and become more difficult to remove. A tar 
remover is recommended.Paintwork, painted body components
Mercedes-Benz approved Paint Care 
should be applied when water drops on the 
paint surface do not “bead up”. This should 
normally be done every 3 to 5 months, 
depending on the climate and washing 
detergent used.
Mercedes-Benz approved Paint Cleaner 
should be applied if the paint surface 
shows signs of embedded dirt (i.e. loss of 
gloss).
Do not apply any of these products or wax 
if your vehicle is parked in the sun or if the 
hood is still hot.
Use the appropriate MB-Touch-Up 
Stick for quick and provisional repairs 
of minor paint damage (i.e. chips from 
stones, vehicle doors, etc.).
!Follow the instructions provided by the 
power washer manufacturer on maintaining a 
distance between the vehicle and the nozzle of 
the power washer.
Never use a round nozzle to power-wash tires. 
The intense jet of water can result in damage to 
the tire.
Always replace a damaged tire.
Always keep the jet of water moving across the 
surface. Do not aim directly at electrical parts, 
electrical connectors, seals, or other rubber 
parts.
iVehicles with KEYLESS-GO*:
If a door handle is hit by a strong jet of water, and 
a SmartKey with KEYLESS-GO* is in close prox-
imity, i.e. within approximately 3 ft 
(approximately 1 m), the vehicle could be inad-
vertently locked or unlocked. 
!Affixing stickers, magnets, adhesive tape or 
similar materials to painted body components 
may damage the paintwork. 
Page 359 of 505
358 Operation
Vehicle care
Engine cleaning
Prior to cleaning the engine compartment, 
make sure to protect electrical 
components and connectors from contact 
with water and cleaning agents.
Corrosion protection, such as MB Anticor-
rosion Wax, should be applied to the 
engine compartment after every engine 
cleaning. Before applying, all control 
linkage bushings and joints should be 
lubricated. The poly-V-belt and all pulleys 
should be protected from any wax. 
Vehicle washing
In the winter, thoroughly remove all traces 
of road salt as soon as possible.
When washing the vehicle underbody, do 
not forget to clean the inner sides of the 
wheels.Hand-wash
Do not use hot water or wash your vehicle 
in direct sunlight. 
Only use a mild car wash detergent, 
such as Mercedes-Benz approved Car 
Shampoo.
Thoroughly spray the vehicle with a 
diffused jet of water.
Direct only a very weak spray towards 
the ventilation intake.
Use plenty of water and rinse the 
sponge and chamois frequently. 
Rinse with clean water and thoroughly 
dry with a chamois. 
Do not allow cleaning agents to dry on 
the finish.Automatic car wash
You can have your car washed in an 
automatic car wash from the start. 
Automatic car washes without brushes are 
preferable.
To protect the filter system, switch the 
climate control or automatic climate 
control to air recirculation mode, see 
“Air recirculation” (
page 189) for 
climate control or (
page 199) for 
automatic climate control.
If the vehicle is very dirty, prewash it 
before running it through the automatic 
car wash.
iVehicles with KEYLESS-GO*:
If a door handle is hit by a strong jet of water, and 
a SmartKey with KEYLESS-GO* is in close 
proximity, i.e. within approximately 3 ft 
(approximately 1 m), the vehicle could be 
inadvertently locked or unlocked. 
!Do not use scouring agents on these parts.
Never apply strong force and only use a soft, 
non-scratching cloth when cleaning the vehicle. 
Do not attempt to wipe the surface with a dry 
cloth or sponge.
Otherwise you nay scratch or damage the paint.
!Do not clean your vehicle in an automatic 
touchless car wash which uses caustic spray. 
Otherwise the caustic spray will damage the soft 
top, paint, or ornamental moldings. 
Page 360 of 505
359 Operation
Vehicle care
Soft top
Frequent cleaning reduces the 
dirt-repellent effect of the soft top.
Intensive cleaning with Mercedes-Benz 
car-care products for convertible soft tops 
can help to restore the dirt-repellent 
effect. Contact an authorized 
Mercedes-Benz Center for detailed 
information.
Light colored soft tops should be cleaned 
frequently to prevent spots and dirt from 
setting in, which could stain and discolor 
the soft top material permanently.
Incorrect cleaning and care, as well as 
ageing, can cause the soft-top seams to 
leak. Have the soft-top seams sealed at a 
Mercedes-Benz Center.Clean soft top with soft top raised and 
locked. Lower the soft top into the storage 
compartment only if the soft top is 
completely dry.
Dry cleaning:
Brush the dry top with a soft-bristled 
brush.
Brush top always from front to rear.
!Make sure that the windshield wiper switch 
is set to0 (
page 55). Otherwise, e.g. the rain 
sensor could activate and cause the wipers to 
move unintentionally. This may lead to vehicle 
damage.
Due to the width of the vehicle, fold in exterior 
rear view mirrors prior to running the vehicle 
through an automatic car wash to prevent 
damage to the mirrors.
iAfter running the vehicle through an 
automatic car wash, wipe any wax off of the 
windshield (
page 362). This will prevent 
smears and reduce wiping noise which can be 
caused by residual wax on the windshield.
When leaving the car wash, make sure that the 
mirrors are folded out. Otherwise they may 
vibrate.
iIf the soft top is kept in the storage 
compartment for a lengthy period, raise it and air 
out with the windows open about every 
4months.
Place a suitable cover over the soft top if you are 
leaving the vehicle parked in the open for an 
extended period of time.
!Remove bird droppings immediately. The 
organic acid damages the material and causes 
the soft top to leak.
Never use a power washer to clean the soft top, 
as you may damage the soft top material.
Do not use sharp-edged instruments for the 
removal of ice and snow.
Never use hot-wax when you run the vehicle 
through an automatic car wash, as you may 
damage the soft top material.
iDepending on the operation mode of the car 
wash, there is the possibility of water drops 
entering the vehicle’s interior. This is not an 
indication of a defect or malfunction in 
the soft top.