light MERCEDES-BENZ E-CLASS 2003 Owners Manual

331 Practical hints
Opening/closing in an emergency
Opening/closing in an emergency
Sliding/pop-up roof* or panorama sliding/pop-up roof*
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
The sliding/pop-up roof drive is located
behind lens1 of the interior overhead
light.
1Screen
Fold screen1 down.

Obtain crank2.

Insert crank2 through hole1.

Turn crank2 clockwise to:

Slide roof closed


Raise roof at the rear

Turn crank2 counterclockwise to:

slide roof open


lower roof at the rearThe sliding/pop-up roof must be resyn-
chronized after being operated manually
(
page 189).
iDo not disconnect the electrical con-
nectors.
ProCarManuals.com

332 Practical hintsReplacing bulbs
Replacing bulbsSafe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See your autho-
rized Mercedes-Benz Center for headlamp
adjustment.
Bulbs Front lamps
iBackup bulbs will be brought into use
when the following lamps malfunction:

Standing lamps


Tail lamps
Lamp
Type
1
Additional turn sig-
nal lamps
LED
2
Turn signal lamp
1156 NA
3
Side marker lamp
W 5 W
4
Low beam
H7 (55 W)
Bi-Xenon*
1
D2S-35 W
1Vehicles with Bi-Xenon headlamps*: Low beam
and high beam use the same D2S-35W lamp. For
safety reasons (high voltage), do not replace the
Bi-Xenon bulb yourself. See your authorized Mer-
cedes-Benz Center.5
High beam
H7 (55 W)
Parking and stand-
ing lamps
W 5 W
6
Fog lamp
HB4/9006
(55 W)
ProCarManuals.com

333 Practical hints
Replacing bulbs
Rear lamps Notes on bulb replacement


Use only 12-volt bulbs of the same type
and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Y o u r h a n d s s h o u l d b e d r y a n d f r e e o f o i l
and grease.


If the newly installed bulb does not light
up, visit an authorized Mercedes-Benz
Center.


Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center:

Additional turn signal lamps in the
exterior rear view mirrors


High mounted brake lamp


Bi-Xenon lamps


Front fog lamps
Lamp
Type
7
High mounted brake
lamp
LED
8
Tail, parking and
standing lamp
HiP
9
License plate lamps
C 5 W
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Bi-Xenon lamps,
it is dangerous to replace the bulb or repair
the lamp and its components. We recom-
mend that you have such work done by a
qualified technician.
ProCarManuals.com

334 Practical hintsReplacing bulbsReplacing bulbs for front lamps
1Bulb socket for turn signal lamp
2High beam bulb
3Bulb socket for parking and standing
lamp
High beam bulb (Halogen headlamps
only)
Switch off the lights.

Open the hood (
page 261).

Press the clamp and remove headlamp
cover.

Pull electrical connector off.

Turn the locking mechanism counter-
clockwise and take out the high beam
bulb2.

Insert the new high beam bulb so that
the base is in the recess of the holder.

Turn the locking mechanism clockwise.

Plug the connector onto the high beam
bulb.

Align headlamp cover and click into
place.
High beam bulb (Bi-Xenon* headlamps
only)

Switch off the lights.

Open the hood (
page 261).

Press the clamp and remove headlamp
cover.

Pull electrical connector off.

Turn the locking mechanism counter-
clockwise and take out the high beam
bulb2.

Insert the new high beam bulb so that
the base is in the recess of the holder.

Turn the locking mechanism clockwise.

Plug the connector onto the high beam
bulb.

Align headlamp cover and click into
place.
Warning!
G
Because of high voltage in Bi-Xenon lamps,
it is dangerous to replace the bulb or repair
the lamp and its components. We recom-
mend that you have such work done by a
qualified technician.
ProCarManuals.com

335 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Switch off the lights.

Open the hood (
page 261).

Twist bulb socket1 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb

Switch off the lights.

Open the hood (
page 261).

Press the clamp and remove headlamp
cover.

Pull out the bulb socket3 with the
bulb.

Pull the bulb out of the bulb socket.

Insert a new bulb in the socket.

Reinstall the bulb socket.

Align headlamp cover and click into
place.Side marker lamp bulb

Switch off the lights.

Carefully slide lamp towards front.

Remove rear end first.

Twist bulb socket counterclockwise
and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket, push in and twist
clockwise.

To reinstall lamp, set rear end in
bumper and let front end snap into
place.
ProCarManuals.com

336 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Tail lamp assemblies
The tail lamps are equipped with HiP bulbs.License plate lamp
1Screw

Switch off the lights.

Loosen both screws1 and remove
lamp.

Replace the tubular lamp and reinstall
lamp.

Retighten the screws.
!To prevent scratches, we recommend
that you have the sidemarker bulb re-
placed by an authorized Mer-
cedes-Benz Center.Warning!
G
The bulbs in the tail lamps cannot be re-
placed individually. The tail lamp bulbs are
under pressure and could explode during an
attempt to replace them.
If the tail lamps are malfunctioning, have
them exchanged at an authorized Mer-
cedes-Benz Center.
ProCarManuals.com

340 Practical hintsFlat tire
Removing the wheel
1Alignment bolt
Unscrew the upper-most wheel bolt
and remove.

Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.

Remove the remaining bolts.

Remove the wheel.Mounting the Minispare wheel

Clean contact surfaces of wheel and
wheel hub.

Guide the spare wheel onto the align-
ment bolt and push it on.

Insert wheel bolts and tighten them
slightly.
Warning!
G
Position the jack only on the jack take-up
brackets designed for this purpose.
If the jack is not properly positioned, the ve-
hicle may slip off of the jack.Warning!
G
The jack is intended only for lifting the vehi-
cle briefly for wheel changes. It is not suited
for performing maintenance work under the
vehicle. Never lie down under the raised ve-
hicle. Do not start the engine when the vehi-
cle is raised.
!Do not place wheel bolts in sand or dirt.
This could result in damage to the bolt
and wheel hub threads.
!To avoid paint damage, place wheel flat
against hub and hold it there while in-
stalling first wheel bolt.
ProCarManuals.com

341 Practical hints
Flat tire

Unscrew the alignment bolt, install last
wheel bolt and tighten slightly.In the case of a flat tire, you may tempo-
rarily use the Minispare* wheel when ob-
serving the following restrictions:


Do not exceed a vehicle speed of
50 mph (80km/h).


Drive to the nearest tire repair facility
to have the flat tire repaired or re-
placed as appropriate.


Do not operate vehicle with more than
one spare wheel mounted.
Warning!
G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be re-
paired immediately. Do not continue to drive
under these circumstances! Contact an au-
thorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect mounting bolts or improperly
tightened mounting bolts can cause the
wheel to come off. This could cause an acci-
dent. Be sure to use the correct mounting
bolts.
Warning!
G
Use only genuine equipment
Mercedes-Benz wheel bolts. They are identi-
fied by the Mercedes star. Other wheel bolts
may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
tip over.
Warning!
G
The dimensions of the Minispare* wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a Minispare*
wheel mounted.
The spare wheel should only be used tempo-
rarily, and replaced with a regular road
wheel as quick as possible.
ProCarManuals.com

347 Practical hints
Jump starting
The battery is located in the trunk on the
right hand side underneath the luggage
box (
page 325). Only jump start the ve-
hicle from the battery in the trunk.

Make sure that the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift selector lever to positionP.1Positive terminal of charged battery
2Positive terminal of discharged battery
3Vehicle ground
4Negative terminal of charged battery

Connect positive terminals1 and2 of
the batteries with the jumper cables.
Clamp cable to charged battery1 first.

Start engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminal4 of the
charged battery and vehicle ground3
(lock ring of the trunk lid lock) in the
trunk with the jumper cable. Clamp ca-
ble to charged battery4 first.

Start the engine of the disabled vehi-
cle.
Now you can again turn on the electrical
consumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
vehicle ground3 and negative
terminal4 and then from positive
terminals1 and2.

Have the battery checked at the next
authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 266).
iThe message
Malfunction - electric
consumers switched off
may appear
in the instrument cluster. It will disap-
pear as soon as the battery is suffi-
ciently charged.
!Vehicles with automatic transmission:
Do not tow-start the vehicle.
ProCarManuals.com

361 Technical data
Rims and tires
Rims and tires
Use only tires and rims which have been
specifically developed for your vehicle and
tested and approved by Mercedes-Benz.
Other tires and rims can have detrimental
effects, such as:

Poor handling characteristics


Increased noise


Increased fuel consumption
Same-sized tires
!Moreover, tires and rims not approved
by Mercedes-Benz may under load ex-
hibit dimensional variations and differ-
ent tire deformation characteristics
that could cause them to come into
contact with the vehicle body or axle
parts. Damage to the tires or the vehi-
cle can be the result.
iFurther information on tires and rims is
available at any authorized
Mercedes-Benz Center. A tire inflation
pressure table is located on the fuel fill-
er cap of the vehicle. The tire pressure
should only be adjusted on cold tires.
Follow the tire manufacturer’s mainte-
nance recommendation included with
the vehicle.
E320
E500
Rims (light alloy)
8J x 16 ET 39
8½J x 17 ET 38
Wheel offset
1.53 in (39 mm)
1.5 in (38 mm)
Summer tires (radial-ply tires)
225/55 R 16 95 H
245/45 R 17 95 H
1
Winter tires (radial-ply tires)
225/55 R 16 95 H M+S
245/45 R 17 95 H M+S
1
1Must not be used with snow chains.
ProCarManuals.com