key MERCEDES-BENZ E-Class 2006 W211 Comand Manual

42 Audio
Radio operation
The system will tune to the strongest
receivable station.
Press  or.
Search begins in ascending or
descending frequency.
The search stops at the next receivable
station.
On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to Radio display
(
page 25).
Pressj ork.
The search stops at the next receivable
station. Tuning via station presets
The seven strongest channels are sorted in
prest 1 to 7 each time you press the
WB soft
key. They are accessed using the number
keypad.
Press one of the number keys
 - .
The system tunes to the station stored
under this number.
Ten presets each are available for the
FM and AM waveband.
The following options are available:
Storing manually using number keys
Storing manually using the Presets
menu
Storing using Autostore Storing manually using the number
keys  - 
Tune to the station to be stored
(
page 38).
Press a number key between and
 and hold it for more than 2 sec-
onds.
The station is now stored in the respec-
tive memory location.
Storing manually using the Presets
menu
Tune to the station to be stored
(
page 38).
Press the Presets soft key.
The Presets menu appears.
Storing FM/AM stations

43 Audio
Radio operation
Use, ,  or  to select a
preset.
Press for more than 2 seconds.
The station will be stored in the respec-
tive memory location.
Storing using Autostore
The Autostore function places stations into
the Autostore memory sorted by reception
quality.
The system stores the station with the
strongest signal in preset 1.
Switch to the desired waveband
(
page 37).
Press the Autost. soft key.
The Autostore preset list appears.
Use to select the
Reprogram Autostore header entry.
Press.
The Autostore search starts. After a de-
lay the new preset assignment ap-
pears. The system tunes to the station
stored on preset 1.
To tune-in another station from the
Autostore preset list (
page 39).
i
The Autostore feature stores presets in
a separate memory, not in the regular
presets seen under the
Presets soft key.
As such, the Autostore memory is only
temporary.

46 Audio
Single CD operation
The COMAND CD drive holds one CD. The
slot for inserting a CD is located above the
display (
page 15).
Insert a CD into the CD slot while
COMAND is switched ON. Insert the
CD face up.
COMAND pulls in the CD. If the CD is
an audio CD, the system switches to
Single CD mode.
Press.
COMAND ejects the CD.
Remove the CD from the slot.
The CD will be pulled in again if it is not
removed from the slot within approx. 7
seconds.
Open the Audio main menu
(
page 36).
Press the CD soft key.
The system switches to Single CD
mode.The center of the status bar shows: The track number and total number
of tracks
The elapsed playing time of the
track
!
If a CD is already loaded, it must be
ejected before inserting the new CD.
Inserting a second CD in the slot with
another CD still loaded will cause dam-
age to the CD drive not covered by the
Mercedes-Benz Limited Warranty.
i
If the CD is an MP3 CD, the system
switches to MP3 mode (
page 53).
Ejecting a CD
Single CD main menu
i
The CD soft key is shaded out if no audio
CD is loaded. The system will not
switch to Single CD mode.
Load an audio CD into the
COMAND CD drive (
page 45).
The
MP3 soft key instead of the CD soft
key is visible when a MP3 CD has been
loaded.

49 Audio
Single CD operation
Starting scan search
Press the Scan soft key.
Ending scan search manually
Press the Scan soft key.
The track playing at the time the scan
is ended remains playing.
Open the Single CD main menu
(
page 46).
Press and hold or .
To stop release or .The following options are available:
Normal sequence
The tracks are played in the normal se-
quence (e.g. track 1, 2, 3 etc.).
The last track is followed by the first
track of the CD.
Repeat track
The current track will be repeated until
this function is deactivated.
Random track
The tracks are played in random order
(e.g. track 3, 8, 5 etc.).
Changing the playback option
In the Single CD main menu
(
page 46) press the Setting soft key. The settings menu is displayed.
The solid circle indicates which op-
tion is currently selected.
Use or  to select a different op-
tion.
Press.
The option is activated. A correspond-
ing display will appear in the status bar
for all options except
Normal sequence.
An option will remain activated even if
the COMAND is switched OFF and then
ON again.
i
When you start the scan search, play-
back option
Normal Sequence is activated
automatically.
Fast forward/reverse
Playback options

54 Audio
MP3 operation
Press the MP3 soft key.
COMAND loads the data on the CD.
It may take a while to load the data, de-
pending on the number of folders and
tracks contained on the CD.
Once the data has been loaded, the
MP3 main menu appears. You will hear
the last track played.1Current folder
2Current track
3Elapsed track playing time
4Track number within the current fold-
er/number of tracks in current folderIf the MP3 tracks are organized into folders
on the disc, you can select a folder from
the COMAND control unit.
The following options are available:
Selecting via folder list
Selecting via extended folder list
Selecting via folder list
i
The MP3 soft key will only appear if an
MP3 CD has been loaded.
i
On MP3 tracks with variable bit rates,
the elapsed track playing time dis-
played may deviate from the actual
time elapsed.
Selecting folders
i
The folder list only contains folders in
which MP3 tracks are stored.

55 Audio
MP3 operation
Only one folder can be viewed at a time.
1Current folder
Press or  to select a folder.
Wait approx. 3 seconds without chang-
ing the selection.
The COMAND changes the folder and
loads the data from the new folder.
It may take a while to load the data, de-
pending on the number of folders and
tracks.Selecting via extended folder list
In the MP3 main menu (page 53)
press the
Folder soft key.
The extended folder list appears.
Use or  to select a folder.
Press.
The COMAND changes the folder and
loads the data from the new folder.
It may take a while to load the data, de-
pending on the number of folders and
tracks.
You may select a track in the current fold-
er.
The following options are available:
Selecting via manual entry of the track
number (
page 57)
Selecting via scan search (page 57)
Selecting via track skip
Selecting via track list
i
The extended folder list only contains
folders in which MP3 tracks are stored.
Selecting a track

57 Audio
MP3 operation
Selecting via manual entry of the track
number
Open the MP3 main menu (page 53).
Press.
The Manual track input display ap-
pears.
1Number of tracks in the current folder
(10 tracks)Entry example: Track 1
Press.
Entry example: Track 10
Press and  in quick succession.
Wait approx. 3 seconds after entering
the number.
The selected track is played.
Selecting via scan search
Scan search is characterised as follows:
Scan search plays each track in the
current folder for approx. 8 seconds.
Scan search can be ended manually.
Scan search automatically stops at the
track listened to before the scan
search was started.
Starting scan search
In the MP3 main menu (page 53)
press the
Scan soft key.
The scan search starts.
i
Entries beyond the number of available
tracks in the current folder are not pos-
sible.
i
The scan search will not function if the
current folder only contains one track.
When you start the scan search, play-
back option
Normal sequence is activated
automatically. Therein scan search is
restricted to the current folder.

58 Audio
MP3 operation
Ending scan search manually
Press the Scan soft key.
The track playing at the time the scan
is ended remains playing.
Open the MP3 main menu (page 53).
Press and hold or .
To stop release or .
The following options are available:
Normal sequence
The COMAND plays tracks in a folder in
succession.
Once all the tracks in a folder have
been played, COMAND begins playing
the track(s) in the next folder on the
disc.
Repeat track
The current track will be repeated until
this function is deactivated.
Repeat folder
The tracks in the current folder will be
repeated until this function is deacti-
vated.
The track sequence is the same as the
Normal sequence option.
Random track
This option is restricted to the tracks in the
current folder. The tracks are played in ran-
dom order.
Random folder
All tracks on the CD are played in random
order.
Switching the playback option
In the MP3 main menu (page 53)
press the
Setting soft key.
The Setting menu appears.
The solid circle indicates which op-
tion is currently selected.
Use or  to select a different op-
tion.
Fast forward/reverse
Playback options

66 Audio
CD changer* operation
Ejecting all CDs
Access the CD changer (page 61).
Press and hold the button of a loaded
magazine compartment 2 for more
than 2 seconds.
The button LEDs of all loaded magazine
compartments will briefly flash red,
several times.
The CD changer ejects the CDs one af-
ter another.
Within 15 seconds, remove each CD
from the slot 1.
The CD will be pulled in again if it is not
removed from the slot within approx.
15 seconds. The system starts playing
the CD again.The ejection procedure is completed
when all CDs are removed, or when the
procedure is aborted by the CD chang-
er.
Retract the CD changer (page 61).
Open the Audio main menu
(
page 36).
Press the CDC soft key.The CD changer main menu appears.
You will hear the CD listened to last. If
the CD listened to last is no longer
available, the unit plays the next avail-
able audio CD.
If the CD contains CD text data, the CD
changer main menu will show the name
of the CD and the title of the track cur-
rently playing.
The status bar also contains:
The track number and total number
of tracks
The elapsed playing time of the
track
CD changer main menu
i
The CDC soft key is shaded out if no CD
is loaded. The system will not switch to
CD changer mode.
Load an audio CD into the
CD changer (
page 61).
The
CDC soft key will only be visible if a
CD changer is connected.

68 Audio
CD changer* operation
Selecting via direct entry of the CD
number
Press one of the  -  keys.
The CD changer switches to the CD
loaded in the appropriate CD changer
compartment.
Selecting via CD Selection menu
Press the Magaz. soft key.
The CD Selection menu appears. You
see the list of all six compartments.An entry shows the CD title if the CD
contains corresponding CD text data.
No text displayed with a CD symbol in-
dicates that the corresponding CD
does not contain any CD text data
An entry shaded out indicates an emp-
ty CD changer compartment.
Use or  to select a CD.
The system will skip empty CD
changer compartments
Press.
The newly selected CD is played.
The following options are available:
Selecting via track skip
Selecting via track list (page 69)
Selecting via manual entry of the track
number (
page 69)
Selecting via scan search (page 70)
Selecting via track skip
On the COMAND control unit
Open the CD changer main menu
(
page 66).
Pressfor forward skipping.
or
Press for backward skipping.
i
The CD fails to be changed if you select
an empty compartment.
Selecting a track