switches MERCEDES-BENZ E-Class 2008 W211 Comand Manual

26 At a glanceMultifunction steering wheelSatellite radio* operation1SAT and position in Preset menu2Channel nameTelephone* operationEither the main display, or a list appears on
display.Telephone main display:
In the list screen, instead of the
READY
mes
-
sage, either a phone book entry or one of
the last 10 outgoing calls will be displayed.
In order to close the list display,
press
t
.
This switches to the telephone main
display.
The following functions are available:
Freq.
function:

You can tune to stations via the station
search
( page
38)
.

Memory
function:

You can tune to stations via the station
presets
( page
39)
.
Setting audio search function
On the multifunction steering wheel,
press
è or ÿ repeatedly until
the Settings...
menu appears in the
multifunction display in the instrument
cluster.

Press
j and switch to the submenu
options.

Press æ or ç and select the Vehicle
menu.

Press
j and select
Audio Search
Function
.

By pressing æ or ç, select Freq.
or
Memory
.
Audio search function
iMemory
is set at the factory.

28 At a glanceMenu systemRight side:

General status information is displayed, re
-
gardless of the selected operating mode. In this example:
ROAMING
= telephone* is logged into a
mobile communications network out
-
side your home network.

= telephone* signal strength
Menu functions and submenus Using the soft keys, you can switch func
-
tions ON or OFF, or open submenus.Example: Radio main menu:

The
Scan
soft key switches the scan
search ON or OFF.

The
Autost.
soft key opens the sub
-
menu for the Autostore settings.
In some situations, soft keys may not have
any function and thus not be available.
Should a soft key not be available, it will
appear shaded out, its characters will ap
-
pear white.Example:

Presets
, Scan
and
Autost.
soft key.
Exiting from submenus You can exit the current submenu by
pressing the
Back
soft key. The display
switches to the next higher menu level.

The system does not accept setting modi
-
fications which have not been stored.

There are exceptions where pressing the Back
soft key will also store new settings.
These exceptions, whenever applicable,
are referenced on the following pages.
iThis information is also displayed in
Navigation* mode (only in map dis
-
plays).

29 At a glance
Quick reference COMAND


Quick reference COMAND
Switching ON 
Turn the key in the steering lock to po
-
sition 1 or 2,
or

Press
.
.
COMAND switches on the last active
system and displays the corresponding
menu.
Switching OFF 
Turn the key in the steering lock to po
-
sition 0 and remove it,
or
Press
.
.
Different volume settings are possible for
Navigation*, Telephone*, or Voice con
-
trol*.A common volume setting is provided for
Radio, Single CD, MP3, CD changer*, AUX
and Satellite radio* operating modes.When setting the volume, the system auto
-
matically stores the setting for the current
-
ly active operating mode. The volume of
navigation announcements can be
changed only during an actual announce
-
ment.
iThe system can be operated as follows:
from COMAND itself, or

from the multifunction steering
wheel
This operating manual describes oper
-
ation from COMAND and from the mul
-
tifunction steering wheel.

Unless otherwise specified, the de
-
scriptions and the displays illustrated
relate to the COMAND control unit.Switching ON/OFF
iWithout the key in position 1 or 2 of the
steering lock, the system automatically
switches OFF again after approx. 30
minutes of inactivity.
iIf a telephone call is in progress (hands
-
free) you cannot switch the COMAND
OFF,
.
is disabled.
Volume

33 At a glance
Quick reference COMAND
Example:

For CD mode: the
LOGIC7
Surround
func
-
tion,

for Satellite radio* mode: the
Speech
func
-
tion.Switching sound functions 
Open the main menu of the appropriate
operating mode
( page
27)
.

Press the
Sound
soft key.
The Sound menu appears.

Use

or

to select the desired
function.

Press

.
The system switches to the selected
function.iYour harman/kardon
® audio system
features the innovative LOGIC7
® multi-
channel surround sound technology
developed for the professional record
-
ing industry.By selecting the “LOGIC7 Surround”
function, LOGIC7
® will be activated.
LOGIC7
® converts any 2-channel ma
-
terial into breathtaking multi-channel
surround sound and that without the
unnatural interpretation of many of to
-
day’s surround sound techniques.
iLOGIC7
® is not an artificial “effects”
button. It automatically adapts itself to
the incoming source material, adjust
-
ing the seven outputs based on the
original acoustic intent of the studio
master.harman/kardon LOGIC7
® creates a
true 360-degree “enveloping” sound
-
field with a maximum “audio sweet
-
spot” for all passengers. harman/kardon LOGIC7
® sets a new
benchmark in musical clarity and sepa
-
ration, giving the listener the impres
-
sion of actually “being there”.LOGIC7
® playback works with all con
-
ventional stereo audio sources (e.g.
stereo CD or stereo radio).

If the radio reception is poor, the sys
-
tem should be switched back to Stan
-
dard stereo playback. Switching back
to Standard stereo playback may im
-
prove reception quality.

42 AudioRadio operation
Press the number buttons in
succession:
!
,
, and

.
Each number entered appears in the
display.

The system tunes to the frequency en
-
tered (in this example: 98.5 Mhz) and
switches back to the FM menu.
Tuning via station search Seven channels are available on the
Weather Band.On COMAND control unit
Switch to the WB waveband by press
-
ing the
WB soft key in the Radio main
menu
( page
37)
.
The system will tune to the strongest
receivable station.

Press
-
or
,
.
Search begins in ascending or

descending frequency.The search stops at the next receivable
station.
On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to Radio display ( page
25)
.

Press
j or
k.
The search stops at the next receivable
station. Tuning via station presetsThe seven strongest channels are sorted in
prest 1 to 7 each time you press the
WB soft
key. They are accessed using the number
keypad.

Press one of the number keys

3
- 
.
The system tunes to the station stored
under this number.
iEntries outside the frequency range are
not possible.Within the AM waveband, the input is
restricted to frequencies within the re
-
spective frequency increment, which
is10 kHz.The system will select the nearest valid
frequency if a frequency outside the
frequency increment is entered.
Tuning to a station on Weather Band

46 AudioSingle CD operation
The COMAND CD drive holds one CD. The
slot for inserting a CD is located above the
display
( page
15)
.

Insert a CD into the CD slot while
COMAND is switched ON. Insert the
CD face up.COMAND pulls in the CD. If the CD is
an audio CD, the system switches to
Single CD mode.

Press
7
.
COMAND ejects the CD.

Remove the CD from the slot.The CD will be pulled in again if it is not
removed from the slot within approx. 7
seconds.

Open the Audio main menu ( page
36)
.

Press the
CD soft key.
The system switches to Single CD
mode.
!Only use CDs, which bear the label
shown and that conform to the com
-
pact digital audio standard

(IEC 60908).Do not play single-CDs (80 mm) with an
adapter. Only use round, 12 cm diame
-
ter CDs.Your CD drive has been designed to
play CDs which correspond to the IEC
60908 standard. Therefore only CDs
not exceeding a thickness of 1.3 mm
can be used.

If you insert thicker data carriers, e.g.
ones that have data on both sides (one
side with DVD data, the other side with
audio data), they cannot be ejected
and will damage the drive.
iThe COMAND CD drive may not be able
to play audio CDs with copy protection.!If a CD is already loaded, it must be
ejected before inserting the new CD.

Inserting a second CD in the slot with
another CD still loaded will cause dam
-
age to the CD drive not covered by the
Mercedes-Benz Limited Warranty.
iIf the CD is an MP3 CD, the system
switches to MP3 mode
( page
54)
.
Ejecting a CD Single CD main menu

66 AudioCD changer* operation
Within 15 seconds, remove the CD
from the slot 1.The CD will be pulled in again if it is not
removed from the slot within approx.
15 seconds. The system starts playing
the CD again.The ejection procedure is completed.

Retract the CD changer
( page
63)
.
Ejecting all CDs 
Access the CD changer
( page
62)
.

Press and hold the button of a loaded
magazine compartment 2 for more
than 2 seconds.The button LEDs of all loaded magazine
compartments will briefly flash red,
several times.

The CD changer ejects the CDs one af
-
ter another.

Within 15 seconds, remove each CD
from the slot 1.The CD will be pulled in again if it is not
removed from the slot within approx.
15 seconds. The system starts playing
the CD again.The ejection procedure is completed
when all CDs are removed, or when the
procedure is aborted by the CD chang
-
er.

Retract the CD changer
( page
63)
.

Open the Audio main menu ( page
36)
.

Press the
CDC
soft key.
iIf you are listening to a CD in the CD
changer and you eject another CD from
the changer:
While ejecting the CD, the system
interrupts CD playback.

The CD you were last listening to
starts from the beginning once the
ejection procedure is completed.
iIf you eject the CD you are currently lis
-
tening to:
The next available audio CD is
played.

If there are no other CDs available,
the system switches to the audio
source listened to before CD chang
-
er mode.
CD changer main menuiThe CDC soft key is shaded out if no CD
is loaded. The system will not switch to
CD changer mode.
Load an audio CD into the

CD changer
( page
63)
.

68 AudioCD changer* operationThe entry appears above the track display.
It shows the number of the current CD.
Use

or

to select another CD
from the list.

Wait approx. 3 seconds without chang
-
ing the selection.The CD is changed. The newly selected
CD is played.
Selecting via direct entry of the CD
number 
Press one of the
3
- 
keys.
The CD changer switches to the CD
loaded in the appropriate CD changer
compartment.
Selecting via CD Selection menu 
Press the
Magaz.
soft key.
The CD Selection menu appears. You
see the list of all six compartments.
An entry shows the CD title if the CD
contains corresponding CD text data. No text displayed with a CD symbol in
-
dicates that the corresponding CD
does not contain any CD text dataAn entry shaded out indicates an emp
-
ty CD changer compartment.

Use

or

to select a CD.
The system will skip empty CD

changer compartments

Press

.
The newly selected CD is played.
iThe system will skip empty CD changer
compartments.
iThe CD fails to be changed if you select
an empty compartment.

78 Satellite radio*Satellite radio operation
The station listened to before remains
tuned.
Example 2: category
POP

In the station list, only channels of catego
-
ry
POP
are available (category mode).

Use

or

to select the category
POP
from the list.
If the station listened to before was of POP
category, the channel remains
tuned. Otherwise the system switches
to the station of
POP
category that was
selected last in this category.
The system will automatically switch to
a station of
POP
category if the currently
selected station is not of the
POP
cate
-
gory. Otherwise, the currently selected
station remains tuned.
Tuning a station within the selected

categoryThe channels identified for the currently
selected category are sorted numerically
by channel number, which appear in the
status bar one at a time. Tuning using COMAND control unit
Press
-
or

.
The search proceeds in ascending or
-
der.
or
Press
,
or

.
The search proceeds in descending or
-
der and stops at the first receivable
station.

83 Telephone*
Important notes

Always drive with extreme caution
when operating the telephone hands-
free.

For safety reasons, the cellular phone
handset should not be used to place or
receive a call while driving.

If the signal is very weak (display in the
status bar):

Wait until reception improves before
placing a call.

Close the windows and reduce all ex
-
ternal noise as much as possible when
using hands-free operation.

Make sure that the air vents are not
pointed in the direction of the micro
-
phones located in the overhead control
panel near the rear view mirror. Adjust
air vents and/or reduce blower speed
if necessary.

A brief disconnection from the cellular
network is not a malfunction, as this
can occur when the network switches
areas. The phone automatically at
-
tempts to again sign on with a network.

If the message
Enter
unlock
code
is
displayed, enter the unlock code
( page
88)
. Only then will you be able
to use all the telephone functions. You will still be able to make 911 emer
-
gency calls
( page
85)
if the tele
-
phone is locked.
The telephone cannot, or not yet, be used
in the following situations:

The telephone is already unlocked, but
it is not yet registered with the net
-
work. The message
NO SERV.
appears in the
status bar. The telephone automatical
-
ly attempts to register with a network.
If there is no network available, “911”
emergency calls can NOT be placed.

If you try to place an outgoing call, the
message
Call
not
possible
is dis
-
played temporarily.

If the message
Telephone
being
activated,
please
wait
is displayed,

If the message
Please
insert
phone
is
displayed.

Insert the cellular phone into the
telephone cradle.
iThis Operator's Manual describes op
-
eration of the telephone using the
COMAND control unit and the multi
-
function steering wheel. Unless other
-
wise specified, the descriptions and
the illustrated displays refer to the
COMAND control unit. Operation of the cellular phone and
voice control system* are explained in
separate operation guides.