instrument cluster MERCEDES-BENZ E CLASS 2019 Owners Manual

NOTEImpairment ofthe operating effi‐ciency oftherestraint systems frominstalling accessory parts or fromrepairsorwelding
Airbags and EmergencyTensioning Devices,aswell as control units and sensorsfortherestraint systems, may be installed inthefol‐lowing areas ofyourvehicle:
RDoors
RDoor pillars
RDoor sills
RSeats
RCockpit
RInstrument cluster
RCenter console
RLateralroof frame
Do not install accessory parts such asaudio systems inthese areas.
Do not carryoutrepairs orwelding.
Haveaftermarket installation of acces‐sories carried out at aqualified special‐istworkshop.
You could jeopardizethe operating safety ofyourvehicle ifyou use parts, tires and wheels aswellas accessoriesrelevanttosafety which havenotbeen approvedbyMercedes-Benz. Safety-rele‐vant systems, e.g.the brake system, may mal‐function. Only use Mercedes-Benz GenuinePartsor parts of equalquality.Only use tires, wheelsand accessoriesthat havebeen specificallyapprovedforyourvehicle model.
Mercedes-Benz GenuineParts are subjecttostrictquality control. Each part has been spe‐cially developed, manufactured or selectedforMercedes-Benzvehicles andfine-tunedforthem.Therefore, only Mercedes-Benz GenuinePartsshould be used.
Morethan 300,000 different Mercedes-BenzGenuineParts areavailablefor Mercedes-Benzmodels.
All authorized Mercedes-Benz Centers maintaina supply of Mercedes-Benz GenuinePartsfor
necessaryservice andrepairwork. In addition,strategically located parts delivery centers pro‐videforquick andreliable parts service.
Always specifythevehicle identification number(VIN) (→page417) when ordering Mercedes-Benz GenuineParts.
Operator's Manual
This Operator's Manual describes all models andallstandard and optional equipmentavailableforyourvehicle atthe time ofthis Operator's Man‐ual goingtopress. Country-specific differencesare possible. Notethatyourvehicle may not beequipped with allfeatures described. This is alsothe casefor systems and functionsrelevanttosafety.Therefore,the equipment onyourvehiclemay differ fromthat inthe descriptions and illus‐trations.
The original purchase agreementforyourvehiclecontains a list of all ofthe systems inyourvehi‐cle.
Shouldyou haveanyquestions concerningequipment and operation, please consult anauthorized Mercedes-Benz Center.
20General notes

RObjects or loads inthe trunk/cargo com‐partment cannotberestrainedbytheseat backrest.
Make surethatthe seat backrest andtherear benchseat/rear seat areengaged beforeeverytrip.
Ifthe seat backrest is not engaged and locked,this will be shown onthe multifunction displayonthe instrument cluster.
\nWARNINGRisk of injuryor death ifthepermissible gross mass ofthechild andchildrestraint system isexceeded
ForLATCH-type (ISOFIX)childrestraint sys‐tems in whichthechild is secured usingtheintegrated seat belt inthechildrestraint sys‐tem,the permissible gross mass ofthechildandchildrestraint system is73lb (33kg).
Ifthechild andthechildrestraint systemtogetherweigh morethan73lb (33kg),theLATCH-type (ISOFIX)childrestraint systemwith integrated seat belt does not offer suffi‐
cient protection. Anexcessive load may beplaced ontheLATCH-type (ISOFIX)child seatattachments andthechild may not berestrained intheevent of an accident,forexample.
Ifthechild andthechildrestraint sys‐temtogetherweigh morethan73lb(33kg), useonly aLATCH-type (ISOFIX)childrestraint systemthat securesthechild withthevehicle seat belt.
Also securethechildrestraint systemwiththeTopTether belt, ifavailable.
Always comply withthe information aboutthemass ofthechildrestraint system:
Rinthe manufacturer's installation and operat‐ing instructionsforthechildrestraint systemused
Ron a label onthechildrestraint system, ifpresent
Regularlycheckthatthe permissible gross massofthechild andchildrestraint system isstillcomplied with.
Whenyou are installing achildrestraint system,observethefollowing:
sAlways observethe correct use andthe suit‐ability ofthe seatsfor attaching achildrestraint system.
sAlways comply withthe manufacturer'sinstallation and operating instructionsforthechildrestraint system used.
sMake surethatthechild'sfeetdo nottouchthe front seat. If necessary,movethe frontseatforward slightly.
Whenyou are installing aLATCH-type(ISOFIX)childrestraint system, observethefol‐lowing:
sWhenyou are using a Group 0/0+ babycar seat and a Group 1rearward-facingchildrestraint system on arear seat:adjustthe front seat sothatthe seat doesnottouchthechildrestraint system.
sWhenyou are using a Group 1forward-facingchildrestraint system:the back‐restofthechildrestraint system must, as
54Occupant safety

far as possible, lieflat againstthe backrestofthevehicle seat.
sYou can havethe headrestraints oftherearseatsremoved and installedbyaqualifiedspecialistworkshop. This may be necessaryforthe use of certainchildrestraint sys‐tems.
sFor certainchildrestraint systems inweightgroup 2 or 3,there may berestrictions inthe maximum size setting, e.g. duetopossi‐ble contact with theroof.
sThechildrestraint system must not beten‐sioned betweentheroof andthe seat cush‐ion and/or be installedfacingthe wrongdirection. Where possible, adjustthe seatcushion inclination accordingly.
sThechildrestraint system must not be putunderstrainbythe headrestraints.Adjustthe headrestraints accordingly.
1LATCH-type (ISOFIX) mounting bracket
Beforeevery trip, make surethattheLATCH-type(ISOFIX)childrestraint system is engaged cor‐rectly in bothmounting brackets inthevehicle.
Removeandstowrelevant covers1.
AttachtheLATCH-type (ISOFIX)childrestraint systemtobothmounting bracketsinthevehicle.
Havingremovedthechild seat,re-attach cov‐ers1.
SecuringTopTether
\nWARNINGRisk of injuryor death iftherear seat backrests are not locked afterinstallingTopTether belts
Iftherear seat backrests are not locked,theycouldfoldforwards intheevent of an acci‐dent or during braking or suddenchanges ofdirection.
As aresult,childrestraint systems cannotperformtheir intended protective function.Rear seat backreststhat are not locked canalso cause additional injuries, e.g. intheevent of an accident.
Always lockrear seat backrests afterinstallingTopTether belts.
Observethe lockverification indicator.
Ifthe seat backrest is not engaged and locked,this will be shown onthe multifunction displayonthe instrument cluster.
Occupant safety55

Securingthechildrestraint system withtheseat belt
Securingthechildrestraint system withtheseat belt ontherear seat
\nWARNINGRisk of injuryiftherearbenchseat/rear seat and seat backrestare not engaged
Iftherear benchseat/rear seat and seatbackrest are not engagedtheycouldfoldfor‐wards, e.g. when braking suddenly or intheevent of an accident.
RIfthis isthe case,thevehicle occupantwould beforced intothe seat beltbytherear benchseat/rear seat orbythe seatbackrest. The seat belt cannotprotect asintended and couldresult in additionalinjury.
RObjects or loads inthe trunk/cargo com‐partment cannotberestrainedbytheseat backrest.
Make surethatthe seat backrest andtherear benchseat/rear seat areengaged beforeeverytrip.
Ifthe seat backrest is not engaged and locked,this will be shown onthe multifunction displayonthe instrument cluster.
When installing a belt-securedchildrestraintsystem, observethefollowing:
sAlways comply withthe manufacturer'sinstallation and operating instructionsforthechildrestraint system used.
sWhen using a category 0/0+ baby carseat and a category Irearward-facingchildrestraint system on arear seat:adjustthe front seat sothatthe seat doesnottouchthechildrestraint system.
sYou can havethe headrestraints oftherearseatsremoved and installedbyaqualifiedspecialistworkshop. This may be necessaryforthe use of certainchildrestraint sys‐tems.
sThe backrest oftheforward-facingchildrestraint system must, asfar as possible, be
resting onthe seat backrest oftherearseat.
sFor certainchildrestraint systems inweightcategory II or III,there may berestrictions inthe maximum size setting, e.g. duetopossi‐ble contact with theroof.
sThechildrestraint system must not be putunderstrain betweentheroof andthe seatcushion and/or be installedfacingthewrong direction. Where possible, adjusttheseat cushion inclination accordingly.
sThechildrestraint system must not be putunderstrainbythe headrestraints.Adjustthe headrestraints accordingly.
sMake surethatthechild'sfeetdo nottouchthe front seat. If necessary,movethe frontseatforward slightly.
The seat belts onthefollowing seats are equip‐ped with a special seat beltretractor:
RFront passenger seat
RRear seats
When enabled,the special seat beltretractorensuresthatthe seat belts ofthe front
Occupant safety57

Depending on whetherthe settingsforthe driveror front passenger seat are selected, onlytheselected seat can bereset.
Foldingthe front seat backrestforwards/back (vehicles with memoryfunction)
With the EASY-ENTRY function,the seat willmoveforwards ifyou havefoldedthe seat back‐restforwards. This makes it easierfor passen‐gerstoget into and out oftherear ofthevehi‐cle.
Tofoldforwards:pull seatrelease handle1andfoldthe seat backrestforwards asfaras it will go.The seat will moveautomaticallytothefore‐most position.
Tofold back:swing backthe seat backresthorizontally.Ifthe seat backrest is not engaged,this willbe shown onthe multifunction display ofthe
instrument cluster.Awarningtone will alsosound.
The seat will moveautomaticallytothestored position.Ifthe set seat position can no longer bereached,e.g. because of luggage intherearfootwell orafter occupants haveenteredtherear ofthevehicle:
Pull seatrelease handle1again andreturnthe seat backresttoan upright position.The seat will lock inthe newfore-and-aftposition.
Switching the seat heating on and off
\nWARNINGRisk of burns duetorepeat‐edly switching onthe seat heating
Repeatedly switching onthe seat heating cancausethe seat cushion and seat backrestpaddingtobecomeveryhot.
The health of persons with limitedtempera‐ture sensitivity or a limited abilitytoreacttohightemperatures may be affected ortheymayeven suffer burn-like injuries.
Seats andstowing95

Foldingtherear seat backrest back
NOTEDamagetothe seat belt
The seat belt could become trapped andthusdamaged whenfolding backthe seat back‐rest.
Make surethatthe seat belt is not trap‐ped whenfolding backthe seat back‐rest.
Movethe driver's or front passenger seatfor‐wards, if necessary.
Fold corresponding seat backrest1backuntil it engages.Left andright seat backrests:ifthe seatbackrest is not engaged and locked,this willbe shown onthe multifunction display ontheinstrument cluster.
Center seat backrest:ifthe seat backrest isnot engaged and locked,red lockverificationindicator2will be visible.
Lockingtherelease catch ofthe centerrearseat backrest
Requirements:RThe left and center seat backrests areengaged and joinedtogether.
You can lockthe center seat backrestreleasecatchifyouwanttosecurethe trunk againstunauthorized access. The center seat backrestcanthen befoldedforwards onlytogether withthe left seat backrest.
106Seats andstowing

Toswitch onthe power supply:press but‐ton1once.You can activatethe windshield wipers,forexample.
The power supplyis switched off again ifthefol‐lowing conditions are met:
RYou openthe driver's door
RYou press button1twice.
Toswitch onthe ignition:press button1twice.The indicator lamps inthe instrument clusterlight up.
The ignition is switched off again if one ofthefollowing conditions is met:
RYou do notstartthevehicle within15minutes andthe transmission is in posi‐tion]orthe electric parking brake isapplied.
RYou press button1once.
Startingthevehicle
Startingthevehicle withthestart/stop but‐ton
Requirements:RThe SmartKeyis located inthevehicle andthe SmartKeybattery is not discharged.
Shiftthe transmissiontoposition]or\\.
Depressthe brake pedal and press button1once.
Ifthevehicle does notstart:switch off non-essential consumers and press button1once.
Ifthevehiclestill does notstart andthePlace the Key in the Marked Space SeeOperator's Manualdisplay message alsoappears inthe multifunction display:startthevehicle in emergency operation mode.
You can switchoffthe engine while drivingbypressing button1for aboutthree seconds. Besuretoobservethe safety notes under "Drivingtips".
Startingthevehicle in emergency operationmodeIfthevehicle does notstart andthePlace theKey in the Marked Space See Operator's Manualmessage appears inthe multifunction display,you canstartthevehicle in emergency operationmode.
Driving and parking13 9

The electric parking brake is applied ifthe trans‐mission is in position]and one ofthefollow‐ing conditions is fulfilled:
RThe engine is switched off.
RThe seat belttongue is not inserted intheseat belt buckle ofthe driver's seat andthedriver's door is opened.
Toprevent application: pullthe handle oftheelectric parking brake.
Inthefollowing situations,the electric parkingbrake is also applied:
RActive Distance AssistDISTRONIC is bringingthevehicletoastandstill.
RThe HOLD function iskeepingthevehiclesta‐tionary.
RActiveParking Assist iskeepingthevehiclestationary.
This isthe case if one ofthefollowing conditionsis also fulfilled:
RThe engine is switched off.
RThe seat belttongue is not inserted intheseat belt buckle ofthe driver's seat andthedriver's door is opened.
RThere is a system malfunction.
RThe power supply is insufficient.
RThevehicle isstationaryfor a lengthyperiod.
Whenthe electric parking brake is applied,theredI(USA) or$(Canada) indicator lampappears inthe instrument cluster.
The electric parking brake is not automaticallyapplied ifthe engine is switched offbythe ECOstart/stop function.
Electric parking brake function (releasingautomatically)
The electric parking brake isreleased whenthefollowing conditions are fulfilled:
RThe engine isrunning.
RThe seat belttongue is inserted intothe seatbelt buckle ofthe driver's seat.
RThe transmission is in position[or^andyou depressthe accelerator pedal oryou
shift from transmission position]to[or^.
RIfthe transmission is in position^,thetrunk lid mustbe closed.
Ifthe seat belttongue is not inserted intotheseat belt buckle ofthe driver's seat,thefollow‐ing conditions must be fulfilled:
RThe driver's door is closed.
RYou movethe transmission out of transmis‐sion position]oryou havepreviouslydrivenfasterthan 2mph (3 km/h).
RIfthe transmission is in position^,thetrunk lid mustbe closed.
Whenthe electric parking brake isreleased,theredI(USA) or$(Canada) indicator lampinthe instrument cluster goes out.
Driving and parking16 3

Applying/releasingthe electric parkingbrake manually
Applying
Push handle1.TheredI(USA) or$(Canada) indica‐tor lamp appears inthe instrument cluster.
The electric parking brake is only securelyapplied ifthe indicator lamp is lit continu‐ously.
Releasing
Switchonthe ignition.
Pull handle1.TheredI(USA) or$(Canada) indica‐tor lamp inthe instrument cluster goes out.
Emergency brakingPress and hold handle1.Whenthevehicle has been brakedto astandstill,the electric parking brake isapplied. TheredI(USA) or$(Can‐ada) indicator lamp appears inthe instru‐ment cluster.
Notes on parkingthevehiclefor anextendedperiod
Ifyou leavethevehicle parkedfor longerthanfourweeks,the disconnected battery may bedamagedbydeep discharge.
Ifyou leavethevehicle parkedfor longerthan sixweeks, it may suffer disuse damage.
Further information can be obtained at aqualified specialistworkshop.
Standby mode (extension of thestarter bat‐tery's period out of use)
Standby mode function
This function is notavailablefor all models.
Ifstandby mode is activated,thevehicle can beparkedfor anextended period of time withoutlosing power.
Standby mode ischaracterizedbythefollowing:
RThestarter battery is preserved.
RThe maximum non-operational time out ofuse is displayed inthe multimedia systemdisplay.
RThe connectiontoonline services is interrup‐ted.
16 4Driving and parking

Overview of driving systems and drivingsafety systems
Inthis section,you willfind information aboutthefollowing driving systems and driving safetysystems:
R360° Camera (→page199)
RABS (Anti-lockBrakingSystem)(→page166)
RActive Distance AssistDISTRONIC(→page177)
RAIR BODYCONTROL (→page190)
RActive Brake Assist (→page170)
RActive LaneKeeping Assist (→page215)
RATTENTION ASSIST (→page 209)
RBAS (BrakeAssistSystem) (→page166)
RHillStart Assist (→page188)
RDYNAMICBODYCONTROL (→page190)
REBD (ElectronicBrakeforceDistribution)(→page170)
RESP®(ElectronicStabilityProgram)(→page167)
RActive Speed Limit Assist (→page180)
RHOLD function (→page189)
RSTEER CONTROL (→page170)
RActiveSteering Assist (→page183)
RActiveParking Assist (→page 203)
RParking AssistPARKTRONIC (→page193)
RRear view camera (→page197)
RCruisecontrol (→page175)
RBlind Spot Assist andActive Blind Spot Assist(→page212)
RTraffic Sign Assist (→page210)
Function of ABS (Anti-lock Braking System)
ABSregulatesthe brake pressure in critical driv‐ing situations:
RDuring braking, e.g. at full brake applicationor insufficient tire traction,the wheels areprevented from locking.
RVehiclesteerability while braking is ensured.
If ABS intervenes when braking,you willfeel apulsing inthe brake pedal. The pulsating brake
pedal can be an indication of hazardousroadconditions and can serveas aremindertotakeextra care while driving.
System limitationsRABS is active from speeds of approx. 5mph(8 km/h).
RABS may be impaired or may not function if amalfunction has occurred andtheyel‐low%ABSwarning lamp lights up contin‐uously inthe instrument cluster aftertheengine isstarted.
Function ofBAS (Brake Assist System)
\nWARNINGRisk of an accident causedbya malfunction inBAS (Brake AssistSys‐tem)
IfBAS is malfunctioning,the braking distancein an emergency braking situation isincreased.
Depressthe brake pedal with fullforcein emergency braking situations. ABSpreventsthe wheels from locking.
16 6Driving and parking