run flat MERCEDES-BENZ E CLASS 2019 Owners Manual

Page 366 of 530

Emergency
Removing the safetyvest
The safetyvests are located inthe safetyvestcompartments inthe driver's and frontpassenger doorstowage compartments.
Toremove:pull out safetyvestbag1byloop2.
Open safetyvestbag1andremovethesafetyvest.
1Maximum number ofwashes
2Maximumwashtemperature
3Do not bleach
4Do not iron
5Do not tumble dry
6Do not dry clean
7Class 2 safetyvest
Therequirements definedbythe legalstandardare only fulfilled ifthe safetyvestisthe correctsize and is fully closed.
The safetyvestmust bereplaced inthefollowingsituations:
Rthereflectivestrips are damaged or dirty.
Rthe maximum permissible number ofwashesisexceeded.
Rthefluorescence hasfaded.
Flat tire
Notes onflat tires
\nWARNINGRisk of accident duetoaflattire
Aflat tire severelyaffectsthe drivingcharac‐teristics aswell asthesteering and brakingofthevehicle.
Tires withoutrun-flatcharacteristics:
Do not drive on with aflat tire.
Changetheflat tire immediately with anemergency sparewheel or spare wheel.Alternatively,consult aqualified spe‐cialistworkshop.
364Breakdown assistance

Page 367 of 530

Tires withrun-flatcharacteristics:
Observethe information andwarningnotes on MOExtended tires (run-flattires).
Intheevent of aflat tire,thefollowing optionsareavailable depending onyourvehicle's equip‐ment:
RVehicles with MOExtended tires:it is pos‐sibletocontinuethe journeyfor a shortperiod of time. Make sureyou observethenotes on MOExtended tires (run-flat tire)(→page 365).
RVehicles with a TIREFIT kit:you canrepairthe tires sothat it is possibletocontinuethejourneyfor a short period of time.Todothis,usethe TIREFIT kit (→page 366).
RVehicles with Mercedes me connect:youcan make a callforRoadside Assistance viatheoverhead control panel inthe case of abreakdown (→page313).
RAllvehicles:changethe wheel(→page 409).
Notes on MOExtended tires (run-flat tire)
\nWARNINGRisk of accident when drivingin emergency mode
When driving in emergency mode,the han‐dlingcharacteristics are impaired. e.g. whencornering, when acceleratingstronglyandwhen braking.
Do notexceedthe permissible maxi‐mum speedfor MOExtended tires.
Avoid any abruptsteering and drivingmaneuvers aswell as drivingoverobstacles (curbs, pot holes, off-road).This applies, in particular,toa loadedvehicle.
Stop driving inthe emergency mode ifyou notice:
Rbanging noise
Rvehicle vibration
Rsmoke which smells likerubber
Rcontinuous ESP®intervention
Rcracksin tire sidewalls
After driving in emergency mode havetherimscheckedbyaqualified special‐istworkshop withregardtotheir furtheruse.
The defective tire must bereplaced ineverycase.
WithMOExtended tires (run-flat tire),you cancontinuetodriveyourvehicleeven ifthere is atotal loss of pressure in one or more tires. How‐ever,the tire affected must not show any clearlyvisible damage.
You canrecognize MOExtended tiresbytheMOExtended marking which appearsonthe sidewall ofthe tire.
Vehicles with tire pressure losswarning sys‐tem:MOExtended tires may only be used in con‐junction withan activated tire pressure losswarning system.
Vehicles with tire pressure monitoring sys‐tem:MOExtended tires may only be used in con‐junction withan activated tire pressure monitor‐ing system.
Breakdown assistance365

Page 368 of 530

If a pressure losswarning message appears inthe multifunction display,proceed asfollows:
RCheckthe tirefor damage.
RIf driving on, observethefollowing notes.
Driving distance possible in emergencymode after the pressure losswarning:
Load condition Driving distance pos‐sible in emergencymode
Partially laden50 miles (80 km)
Fully laden19miles (30 km)
The driving distance possible in emergencymode mayvarydepending onthe drivingstyle.Observethe maximum permissible speed of50mph (80 km/h).
If a tire has goneflat and cannot bereplacedwith an MOExtended tire,you can use astand‐ard tire as atemporary measure.
TIREFIT kitstoragelocation
The TIREFIT kit is located underthe trunkfloor.
1Tiresealant bottle
2Tireinflation compressor
Usingthe TIREFIT kit
Requirements
Requiredtools:
RTiresealant bottle
RTIREFITsticker
RTireinflation compressor
RGloves (depending onthevehicle equipment)
TIREFIT kitstorage location: (→page 366)
You can use TIREFIT tire sealanttoseal perfora‐tion damageof upto0.16in (4 mm), particularlythose inthe tire contact surface.You can useTIREFIT in outsidetemperatures downto-4 °F(-20 °C).
\nWARNINGRisk of accident when usingtire sealant.
Inthefollowing situations,the tire sealant isunabletoprovide sufficient breakdown assis‐tance, as it is unabletosealthe tire properly:
RThere are cuts or punctures inthe tirelargerthanthose previously mentioned.
RThe wheelrim is damaged.
RYou havedriven at averylow tire pres‐sure or on aflat tire.
Do not continue driving.
Consult aqualified specialistworkshop.
366Breakdown assistance

Page 369 of 530

\nWARNINGRisk of injuryand poisoningfrom tire sealant
The tire sealant is harmful and causes irrita‐tion. Do not allow ittocome into contactwith the skin,eyes or clothing, and do notswallow it. Do not inhale tire sealant fumes.Keepthe tire sealantawayfromchildren.
Ifyou come into contact withthe tire sealant,observethefollowing:
Rinse offthe tire sealant fromyour skinimmediately usingwater.
If tire sealantgets intoyoureyes,thor‐oughlyrinse outtheeyes using cleanwater.
If tire sealant has been swallowed,immediatelyrinse outthe mouththor‐oughly and drink plenty ofwater.Do notinducevomiting and seek medicalattention immediately.
Change out of any clothes contamina‐ted with tire sealant immediately.
If allergicreactions occur, seek medicalattention immediately.
NOTEOverheating duetothe tire infla‐tion compressorrunningtoo long
Do notrunthe tire inflation compressorfor longerthanten minutes withoutinterruption.
Comply withthe manufacturer's safety notes onthesticker onthe tire inflation compressor.
Havethe tire sealant bottlereplaced in aquali‐fied specialistworkshopeveryfiveyears.
Do notremoveanyforeign objects whichhaveenteredthe tire.
Affix part1ofthe TIREFITstickertotheinstrument cluster withinthe driver'sfield ofvision.
Affix part2ofthe TIREFITsticker nearthevalve onthe wheel withthe defective tire.
Pull plug4withthe cable and hose5outofthe tire inflation compressor housing.
Breakdown assistance367

Page 370 of 530

Pushthe plug of hose5intoflange6oftire sealant bottle1untilthe plug engages.
Place tire sealant bottle1head downwardsintorecess2ofthe tire inflation compres‐sor.
Removethevalve cap fromvalve7onthedefective tire.
Screwfilling hose8ontovalve7.
Insert plug4into a12V socket inyourvehicle.
Switchthe ignition on.
Press on and off switch3onthe tire infla‐tion compressor.The tire inflation compressor is switched on.The tire is inflated. First, tire sealant is pum‐ped intothe tire. The pressure may brieflyrisetoapproximately 500 kPa (5 bar/73 psi).
Do not switch offthe tire inflation compres‐sor duringthis phase.
Letthe tire inflation compressorrunfor amaximum often minutes.The tire shouldthen haveattained a tirepressure of at least 200 kPa (2.0 bar/29 psi).
If tire sealant leaks out, make sureyou cleantheaffected area asquickly as possible. It is prefera‐bletouse clearwater.
Ifyouget tire sealant onyour clothing, haveitcleaned as soon as possible with perchloroethy‐lene.
If, afterten minutes, a tire pressure of200 kPa (2.0 bar/29 psi) has not been ach‐ieved:
Switch offthe tire inflation compressor.
Unscrewthefilling hose fromthevalve ofthedefective tire.
Please notethat tire sealant may leak out whenunscrewingthefilling hose.
Driveforwards orreverseveryslowlyforapproximately 33ft(10 m).
Pump upthe tire again.After a maximum often minutesthe tirepressure must be at least 200 kPa (2.0 bar/29 psi).
\nWARNINGRisk of accident duetothespecified tire pressure not beingreached
Ifthe specified tire pressure is notreachedafterthe specified time,the tire istoo badlydamaged. The tire sealant cannotrepairthetire inthis instance.
368Breakdown assistance

Page 388 of 530

Tirepressure
Notes on tire pressure
\nWARNINGRisk of accident duetoinsuf‐ficient orexcessive tire pressure
Underinflated oroverinflated tires posethefollowingrisks:
RThe tires may burst, especially astheload andvehicle speed increase.
RThe tires maywearexcessively and/orunevenly,which maygreatlyimpair tiretraction.
RThe drivingcharacteristics, aswell assteering and braking, may be greatlyimpaired.
Comply withtherecommended tirepressure andcheckthe tire pressure ofall tires includingthe spare wheelregu‐larly:
Rat least once a month
Rwhenthe loadchanges
Rbefore embarking on a longer journey
Rif operating conditionschange, e.g. off-road driving
Adjustthe tire pressure as necessary.
Driving withtire pressurethat istoo high ortoolow can:
RShortenthe service life ofthe tires.
RCause increased tire damage.
RAdversely affect drivingcharacteristics andthus driving safety,e.g. dueto hydroplaning.
\nWARNINGRisk of an accident duetoinsufficient tire pressure
Tires with pressurethat istoo low canover‐heat and burstas aresult.
In addition,theyalso suffer fromexcessiveand/or irregularwear, which can significantlyimpairthe braking properties andthe han‐dlingcharacteristics.
Avoidexcessively low tire pressures inallthe tires, includingthe spare wheel.
Tirepressure which istoo low can cause:
RTiredefects as aresult ofoverheating
RImpaired handlingcharacteristics
RIrregularwear
RIncreased fuel consumption
\nWARNINGRisk of accident fromexces‐sive tire pressure
Tires withexcessively high pressure canburstbecausetheyare damaged more easilybyhighwayfill, pot holesetc.
In addition,theyalso suffer from irregularwear, which can significantly impairthe brak‐ing properties andthe handlingcharacteris‐tics.
Avoidexcessively high tire pressures inallthe tires, includingthe spare wheel.
Excessively high tire pressure canresult in:
RIncreased braking distance
RImpaired handlingcharacteristics
RIrregularwear
386Wheels and tires

Page 394 of 530

The tire pressure losswarning system does notreplacethe needtoregularlycheckthe tire pres‐sure.
System limitations
The system may be impaired or may not functionparticularlyinthefollowing situations:
RIncorrectly set tire pressure
RSudden pressure loss caused,forexample,byaforeign object penetratingthe tire
RSteady pressure loss in several tires
The system has arestricted or delayed functionparticularly inthefollowing situations:
RPoor ground conditions, e.g. snow or gravel
RDriving withsnowchains
RWhen adopting averysporty drivingstylewith high cornering speeds or sudden accel‐eration
RDriving with a high load
Be suretoalso observethefollowing furtherrelated subjects:
RNotes on tire pressure (→page 386)
RDisplay messages aboutthe tires(→page 460)
Restartingthe tire pressure losswarningsystem
Requirements:RTherecommended tire pressure is correctlysetfortherespective operatingstatus oneach ofthefour wheels (→page 386).
Restartthe tire pressure losswarning system inthefollowing situations:
RThe tire pressure haschanged.
RThe wheels or tires havebeenchanged ornewly installed.
On-board computer:
Service Tires
Swipe downwards ontheTouch Control onthe left-hand side ofthesteering wheel.TheTire Pressure Control SystemActiveRestart: Press Touch Controlmessageis shown inthe multifunction display.
Restartthe tire pressure losswarning system inthefollowing situations:
RThe tire pressure haschanged.
RThe wheels or tires havebeenchanged ornewly installed.
Tobegintherestart, presstheTouch Controlonthe left-hand side ofthesteering wheel.TheTire Pressure Now OK?message isshown inthe multifunction display.
SelectYes.
Toconfirmtherestart, presstheTouch Con‐trol onthe left-hand side ofthesteeringwheel.TheRun Flat Indicator Restartedmessage isshown inthe multifunction display.
Afteryou havedrivenfor afew minutes,thetire pressurelosswarning system monitorsthe set tire pressures of allthe tires.
Be suretoalso observethefollowing furtherrelated subjects:
RNotes on tire pressure (→page 386)
392Wheels and tires

Page 407 of 530

Changing a wheel
Notes on selecting, installing andreplacingtires
Mercedes-AMGvehicles:observethe notes inthe Supplement. Otherwise,you may notrecog‐nize dangers.
You can askfor informationregarding permittedwheel/tire combinations at an authorizedMercedes-Benz Center.
\nWARNINGRisk of accident duetoincor‐rect dimensions of wheels and tires
If wheels and tires ofthe wrong size areinstalled,the wheel brakes or wheel suspen‐sion components may be damaged.
Alwaysreplace wheels and tires withthosethat fulfillthe specifications ofthe original part.
Whenreplacing wheels, make suretofitthecorrect:
RDesignation
RModel
Whenreplacing tires, make suretoinstallthecorrect:
RDesignation
RManufacturer
RModel
\nWARNINGRisk of injurythroughexceed‐ingthe specified tire loadrating orthepermissible speedrating
Exceedingthe specified tire loadrating orthe permissible speedrating may leadtotiredamageandtothe tires bursting.
Therefore, only use tire types and sizesapprovedforyourvehicle model.
Observethe tire loadrating and speedratingrequiredforyourvehicle.
NOTEVehicle and tire damagethroughtire types and sizesthat havenot beenapproved
For safetyreasons, onlyuse tires, wheelsand accessories which havebeen speciallyapprovedbyMercedes-Benzforyourvehicle.
These tires are specially adaptedtothe con‐
trol systems, such as ABS, ESP®and4MATIC, and marked asfollows:
RMO = Mercedes-Benz Original
RMOE = Mercedes-Benz Original Extended(run-flat tire onlyfor certain wheels)
RMO1 = Mercedes-Benz Original (only cer‐tain AMG tires)
Certaincharacteristics, such as handling,vehicle noise emissions, fuel consumption,etc. mayotherwise be adversely affected.Furthermore,other tire sizes couldresult inthe tiresrubbing againstthe body and axlecomponents when loaded. This couldresultin damagetothe tire orthevehicle.
Wheels and tires405

Page 409 of 530

Observethefollowing when selecting, installingandreplacing tires:
ROnly use tires and wheels ofthe same type(summer tires, winter tires, MOExtendedtires) andthe same make.
ROnly install wheels ofthe same size on oneaxle (left andright).
It is only permissibletoinstall a differentwheel size intheevent of aflat tire in ordertodrivetothe specialistworkshop.
ROnly install tires ofthe correct size ontothewheels.
RVehicles with a tire pressure monitoringsystem:All installed wheels must be equip‐ped with functioning sensorsforthe tirepressure monitoring system.
RAttemperatures below 45 °F (7 °C), use win‐ter tires or all-season tires marked M+Sforall wheels.
Winter tires bearingtheMsnowflake sym‐bol in additiontothe M+S marking providethe best possible grip in wintryroad condi‐tions.
RFor M+S tires, only use tires withthe sametread.
RObservethe maximum permissible speedforthe M+S tires installed.
Ifthis is belowthevehicle's maximum speed,this must be indicatedbyan appropriatelabel inthe driver'sfield of vision.
RBreak in new tires at moderate speedsforthefirst 60 miles (100 km).
RReplacethe tires after sixyears atthe latest,regardless ofwear.
RWhenreplacing with tires that do notfea‐turerun-flatcharacteristics:vehicles withMOExtended tires are not equipped with aTIREFIT kit atthefactory.Equipthevehiclewith a TIREFIT kit afterreplacing with tiresthat do notfeaturerun-flatcharacteristics,e.g. winter tires.
For more information on wheels and tires, con‐tact aqualified specialistworkshop.
Be suretoalso observethefollowing furtherrelated subjects:
RNotes on tire pressure (→page 386)
RTireand Loading Information placard(→page 393)
RTiresize designation, load-bearing capacity,speedrating and load index (→page 400)
RTirepressuretable (→page 387)
Notes onrotating wheels
\nWARNINGRisk of injurythrough differ‐ent wheel sizes
Interchangingthe front andrear wheels ifthewheels or tires havedifferent dimensionsmay severelyimpairthe drivingcharacteris‐tics.
The wheel brakes or wheel suspension com‐ponents may also be damaged.
Rotatefront andrear wheels onlyifthewheels and tires are ofthe same dimen‐sions.
Wheels and tires407

Page 412 of 530

Aluminum hub cap
Toremove:position socket2on hub cap1.
The socket can befound inthe tire-changetool kit.
Position wheel wrench3on socket2.
Using wheel wrench3, turn hub cap1counter-clockwise andremoveit.
Toinstall:position hub cap1and turn untilit is completelyflush withthe wheel.
Position socket2on hub cap1.
Attachwheel wrench3tosocket2andtightenthe hub cap clockwise.Specified tighteningtorque:18lb-ft(25 Nm).
Raisingthevehicle whenchanging a wheel
Requirements:RThere are no persons inthevehicle.
RThevehicle has been preparedfor a wheelchange (→page 409).
RThe hub caps havebeenremoved(→page 409).
Important notes on usingthe jack:
RUse onlythevehicle-specific jackthat hasbeentested and approvedbyMercedes-Benztoraisethevehicle.
RThe jack is only designedforraising andholdingthevehiclefor a short time while awheel is beingchanged and notfor mainte‐nanceworkunderthevehicle.
RThe jack must be placed on afirm,flat andnon-slip surface. If necessary,use a large,flat, load-bearing, non-slip underlay.
RThefootofthe jack must be positionedverti‐cally underthe jack support point.
Rules of conduct whenthevehicle israised:
RNever placeyour hands orfeetunderthevehicle.
RNever lie underthevehicle.
RDo notstartthe engine and do notreleasethe electric parking brake.
RDo not open or close any doors orthe trunklid.
41 0Wheels and tires

Page:   1-10 11-20 next >