lock MERCEDES-BENZ E-CLASS COUPE 2022 Workshop Manual

*
N
NO
OTE
TE Damage caused bytopping up too
much engine oil To
o much engine oil can damage the engine or
th e catalytic con verter. #
Have excess engine oil remo ved at a
qu ali/ed specialist workshop. %
Depending on driving st yle, theve hicle con-
sumes up to0.8 litre of oil per 1000 km. The
oil consum ption may be higher than this when
th eve hicle is new or if you frequently drive at
high engine speeds. #
Turn cap 1anti-clockwise and remo veit. #
Top up the engine oil. #
Replace cap 1and turn it clockwise until it
engages. #
Check the oil le vel again (/ page 308). Chec
Chec
king t
king t he coolant lev
he coolant lev el
el &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of scalding from hot cool-
ant
If yo u open the cap, you could be scalded. #
Let the mo tor cool down before opening
th e cap. #
When opening the cap, wear pr otective
glo ves and saf ety glasses. #
Open the cap slo wlytorelease pressure. 310
310
Maintenance and care

#
Park theve hicle on a le vel sur face. #
Check the coolant temp erature display on the
inst rument displa y.
The coolant temp erature must be below 70°C. #
Slowly turn cap 1anti-clockwise torelease
ove rpressure. #
Continue turning cap 1anti-clockwise and
re mo veit. The coolant le
vel is cor rect in thefo llowing cases:
R Ifth e engine is cold, the coolant is up to
mar ker bar 2.
R Ifth e engine is warm,th e coolant is up to
1.5 cm overth e mar ker bar 2. #
If necessar y,re/ll with coolant that has been
appr ovedfo r Mercedes-Benz.
% Further information on coolant (/ page 370) T
T
opping up t
opping up t he windscr
he windscreen w
een washer syst
asher syst em
em &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING ‑ Risk of /re and injury due to
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. It could ignite if it comes into contact
with hot engine component parts or the
ex haust system. #
Make sure that no windscreen washer
concent rate spills out next tothe /ller
opening. Maintenance and care
311 311

Se
Se
tting up t
tting up t he w
he war
arning tr
ning tr iangle
iangle #
Fold side re0ectors 1upwards toform a tri-
angle and attach at theto p using upper press-
stud 2. #
Fold legs 3down and out tothe side. F
F
irs
irst-aid kit t-aid kit (soT
(soTsided) ov
sided) over
erview
view Fi
rs t-aid kit (soT sided) 1is on the leT or right in
th e boot, depending on theve hicle version. R
R
emo
emo ving t
ving t he
he/re
/re e
extinguisher
xtinguisher &
W
WARNING
ARNING Risk of accident due toan
inco rrectly secured /re extinguisher in the
driver's foot we ll
A /re extinguisher may impede pedal tr avel or
block a depressed pedal.
This jeopardises the operating and road saf ety
of theve hicle.
The /re extinguisher can be 0ung around and
injure the driver or other vehicle occupants. #
Always store and secure the /re extin-
guisher in the brac ket. #
Do not remo vethe /re extinguisher while
driving. Breakdown assistance
321 321

T
T
o
o w
w -st
-st ar
ar ting or to
ting or towing away
wing away P
P
er
er mitt
mitt edto
ed towing met
wing met hods
hods *
N
NO OTE
TE Damage from automatic braking If one of
thefo llowing functions is activated,
th eve hicle brakes automatically in cer tain sit-
uations:
R Active Brake Assist
R Active Distance Assist DISTRONIC
R HOLD function
R Active Parking Assist
To avo id damage totheve hicle, deactivate
th ese systems in thefo llowing or similar situa-
tions: #
During towing #
In a car wash Mercedes-Benz
recommends transporting your
ve hicle in the case of a breakdown, rather than
to wing it away.
Fo rto wing, use a tow rope or tow bar with bo th
axles on thegr ound. Do not use tow bar systems. *
N
NO OTE
TE Damage totheve hicle due to tow-
ing awa y incor rectly #
Obser vethe inst ructions and no tes on
to wing away. V
V
ehicles wit
ehicles wit h r
h rear wheel dr
ear wheel dr ive
ive P
P
er
er mitt
mitt edto
ed towing met
wing met hods
hods
Bo th axles on
th egr ound Ye
s, maximum 50 km at
50 km/h
Fr ont axle
ra ised No
Re ar axle
ra ised Ye
s, if the steering wheel is
/xed in the centre position
with a steering wheel lock 4MA
4MA
TIC v
TIC v ehicles
ehicles P
P
er
er mitt
mitt edto
ed towing met
wing met hods
hods
Bo th axles on
th egr ound Ye
s, maximum 50 km at
50 km/h
Fr ont axle
ra ised No
Re ar axle
ra ised No T
T
o
o wing wit
wing wit h a r
h a raised axle:
aised axle: towing should be per-
fo rm ed byato wing compan y. T
T
o
o wing t
wing t he v
he vehicle wit
ehicle wit h bot
h both axles on t
h axles on t hegr
he ground
ound #
Obser vethe no tes on the permitted towing
me thods. #
Make sure that the battery is connected and
ch arge d.
Obser vethefo llowing points when the battery is
dischar ged:
R The vehicle cann otbe star ted. Breakdown assistance
333
333

R
the electric parking brake cannot be released
or applied
R V
Vehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: the
transmission cannot be shiTed toposition i
or j.
% V
V ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: ifthe
transmission cannot be shiTed toposition i
or if the display does not show anything,
transport theve hicle (/ page 335). A towing
ve hicle with liTing equipment is requ ired for
ve hicle transpor tation.
* NO
NO TE
TEDamage due to towing away at
ex cessively high speeds or over long dis-
ta nces The driv
etra in could be damaged when towing
at excessively high speeds or over long distan-
ces. #
Atowing speed of 50 km/h must not be
ex ceeded. #
Atowing dis tance of 50 km must not be
ex ceeded. &
W
WARNING
ARNING Risk of accident when towing a
ve hicle which is too heavy
If th eve hicle tobe tow- star ted or towe daway
is heavier than the permissible gross mass of
yo ur vehicle, thefo llowing situations can
occur:
R theto wing eye may become de tach ed.
R theve hicle/trailer combination may
swer veorove rturn. #
Before tow- starting or towing away,
ch eck if theve hicle tobe tow- star ted or
to we dawa yex ceeds the permissible
gr oss mass. If a
vehicle must be tow- star ted or towe dawa y,its
permissible gross mass must not exceed the per-
missible gross mass of theto wing vehicle. #
Information on the permissible gross mass of
th eve hicle can be found on theve hicle identi-
/cation plate (/ page 361). #
V
V ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: do not
open the driver's door or front passenger door;
the transmission otherwise automati-
cally shiTs toposition j. #
Fitth eto wing eye (/ page 337). #
Fasten theto wing device.
* N
NOOTE
TE Damage due toincor rect connec-
tion of theto w bar #
Only connect theto w rope or tow bar to
th eto wing eyes. #
Deactivate the automatic locking mechanism
(/ page 81). #
Do not activate the HOLD function. #
Deactivate tow- awa y protection (/ page 97). #
Deactivate Active Brake Assist (/ page 214). #
V
Vehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: shiTto
position i. #
Release the electric parking brake. 334
334
Breakdown assistance

F
F
itting and r
itting and r emo
emoving t
ving t heto
he towing eye
wing eye #
Press the mark on co ver1 inwa rds and
re mo ve. #
Screw intheto wing eye clockwise as far as it
will go and tighten. V
V
ehicles wit
ehicles wit h a tr
h a trailer hitc
ailer hitc h:
h:vehicles with a trailer
hitch do not ha veare ar brac ketfo rth eto wing
ey e. Fasten theto w bar tothe trailer hitch. #
Make sure that co ver1 engages in the
bumper when youre mo vetheto wing eye.
* N
NO OTE
TE Damage totheve hicle due toincor-
re ct use of theto wing eye or trailer hitch When a
towing eye or trailer hitch is used to
re co ver a vehicle, theve hicle may be damaged
in the process. #
Only use theto wing eye or trailer hitch to
to w awa y or tow start theve hicle. #
Do not use theto wing eye or trailer hitch
to to wtheve hicle during reco very. T
T
o
o w
w -st
-st ar
arting t
ting t he v
he vehicle
ehicle V V
ehicles wit ehicles wit h aut
h automatic tr
omatic tr ansmission
ansmission
* NO
NOTE
TEDamage tothe automatic transmis-
sion due to tow-starting The au
tomatic transmission may be damaged
in the process of tow- starting vehicles with
automatic transmission. #
Vehicles with automatic transmission
must not be tow- star ted. #
Vehicles with an automatic transmission must
not be tow- star ted. Electr
Electr
ical fuses
ical fuses N
No
ot
tes on electr
es on electr ical fuses
ical fuses &
W
WARNING
ARNING Risk of accident and inju rydue
to ove rloaded lines
If yo u manipulate or bridge a faulty fuse or if
yo ure place it with a fuse with a higher amper-
age, the electric line could be overloaded. Breakdown assistance
337
337

#
Always switch o. the windscreen wipers
and theve hicle /r stifyo u need toopen
th e bonnet. #
Turn clips 2on co ver1 aqu arter-turn to
anti-clockwise. #
Pull co ver1 upwards in the direction of the
ar ro w. #
Remo veany existing moisture from the fuse
box using a dry clo th. #
Loosen scr ews4 and remo vefuse box lid 3
from theto p.
Closing
Closing #
Check whe ther the seal is positioned cor rectly
in cap 3. #
Insert lid 3into the brac ket at there ar of the
fuse box. #
Fold down lid 3ofthe fuse box and tighten
scr ews4. #
Insert co ver1 on bo thsides. #
Turn clips 2on co ver1 aqu arter-turn
clockwise. #
Close the bonnet. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the coc
he coc kpit
kpit R
Obser vethe no tes on elect rical fuses
(/ page 337).
The fuse box is on the driver's side on the side of
th e cockpit under a co ver. #
Toopen and close it, consult a Mercedes-Benz
Service Centre. Opening and closing t
Opening and closing t
he fuse bo
he fuse box in t
x in the fr
he front
ont
passeng
passeng er f
er foo
ootw
twell
ell Obser
vethe no tes on elect rical fuses
(/ page 337). Breakdown assistance
339
339

The
tool bag contains:
R Jack
R Wheel wrench
R Centring pin
R Folding chock
R Ratchet for jack Pr
Pr
epar
epar ing t
ing the v
he vehicle f
ehicle f or a wheel c
or a wheel c hange
hange R
R
eq
eq uir
uir ements:
ements:
R The vehicle is not on a slope.
R The vehicle is on solid, non-slippery and le vel
gr ound. R
The requ ired tyre-change tool kit is available.
% Ifyo ur vehicle is not equipped with the tyre-
ch ange tool kit, consult a quali/ed specialist
wo rkshop to/nd out about sui table tools. #
Apply the electric parking brake manuall y. #
Movethe front wheels tothe straight-ahead
position. #
ShiT the transmission toposition j. #
V
Vehicles wit
ehicles wit h lev
h level contr
el contr ol syst
ol system:
em:setthe nor-
mal vehicle le vel (/ page 223). #
Switch o. theve hicle. #
Make sure that theve hicle cann otbe star ted. #
Place choc ks orother suitable items under the
front and rear of the wheel that is diagonal ly
opposite the wheel you wish tochange. #
If necessar y,remo vethe wheel trim/hub caps
(/ page 351). #
Raise theve hicle (/ page 352). R
R
emo
emo ving and
ving and /tting
/ttingt
the wheel tr
he wheel tr im/hub caps
im/hub caps R
R
eq
eq uir
uir ements:
ements:
R The vehicle is prepared for a wheel change
(/ page 351).
Plas
Plas tic hub cap
tic hub cap #
T
To r
o r emov
emov e:
e:turn the centre co ver of the hub
cap anti-clockwise and remo vethe hub cap. #
T
To
o /t:
/t: make sure that the centre co ver of the
hub cap is turned anti-clockwise. #
Position the hub cap and turn the centre co ver
clockwise until the hub cap engages ph ysically
and audibl y.
Aluminium hub cap
Aluminium hub cap Wheels and tyres
351
351

#
T
To r
o r emov
emov e:
e:position soc ket2 from the tyre-
ch ange tool kit on hub cap 1.#
Position wheel spanner 3on soc ket2. #
Using wheel spanner 3, turn hub cap1
anti-clockwise and remo veit. #
T
To
o /t:
/t: follow the inst ructions abo veinreve rse
order.
% Speci/ed
Speci/ed tight
tightening t
ening t orq
orque:ue: 25 Nm. R
R
aising t
aising t he v
he vehicle when c
ehicle when c hanging a wheel
hanging a wheelR
R
eq
eq uir
uir ements:
ements:
R There are no persons in theve hicle.
R The vehicle has been prepared for a wheel
ch ange (/ page 351).
R The wheel trims and hub caps ha vebeen
re mo ved (/ page 351).
Impor tant no tes on using the jack:
R Use only a vehicle-speci/c jack that has been
appr ovedby Mercedes-Benz toraise theve hi-
cle.
R The jack is only designed forra ising and hold-
ing theve hicle for a short time while a wheel is being
changed and not for maintenance
wo rkunder theve hicle.
R The jack must be placed on a /rm, 0at and
non-slip sur face. If necessar y,use a lar ge, 0at,
load-bearing, non-slip underla y.
R The foot ofthe jack must be positioned verti-
cally under the jack support point. Ru
les of conduct when theve hicle is raised:
R Never place your hands or feet under theve hi-
cle.
R Never lie under theve hicle.
R Do not start theve hicle and do not release the
electric parking brake.
R Do not open or close any doors or the boot
lid. 352 352
Wheels and tyres

#
Position support 2of jack 4on jack sup-
port point 1. #
Turn ratchet 3clockwise until support 2
sits comple tely on jack support point 1and
th e base of the jack lies evenly on thegr ound. #
Turn ratchet 3until the tyre is raised a maxi-
mum of 3 cm from thegr ound. #
Loosen and remo vethe wheel (/ page 354). R
R
emo
emo ving a wheel
ving a wheel R R
eq eq uir
uir ements:
ements:
R The vehicle is raised (/ page 352).
* NO
NOTE
TEMercedes-AMG vehicles #
Obser vethe no tes in the Supplement.
Yo u could otherwise failto recognise
dangers. When
changing a wheel, avoid applying any force
to the brake discs, as this could impair the le vel of
comfort when braking.
* N
NOOTE
TE Damage tothe wheels' plastic ele-
ments when changing a wheel Plastic elements on wheels may be damaged
when removing and repositioning the wheel. #
Do not raise the wheels bythe plastic
elements when removing and reposition-
ing. *
N
NOOTE
TE Damage tothre ading from dirt on
wheel bolts #
Do not place wheel bolts in sand or on a
dirty sur face. #
Unscr ewthe uppermost wheel bolt com-
ple tely. #
Screw cent ring pin 1into theth re ad ins tead
of the wheel bolt. #
Unscr ewthere maining wheel bolts com-
ple tely. #
Remo vethe wheel. 354 354
Wheels and tyres