MERCEDES-BENZ E320 2005 W211 Owner's Manual
Page 231 of 506
229 Controls in detail
Panorama roof with power tilt/sliding panel*
Opening and closing the panorama roof
with tilt/sliding panel
To open, close, raise, or lower the
tilt/sliding panel, move the roof panel
switch to resistance point in the re-
quired direction of arrows1 to4.
Release the roof panel switch when the
tilt/sliding panel has reached the de-
sired position.
Fully opening (Express-open) the pan-
orama roof with tilt/sliding panel
Move the roof panel switch past the re-
sistance point in the direction of
arrow1 and release.
The tilt/sliding panel opens complete-
ly.
Stopping the panorama roof with
tilt/sliding panel during Express-open
Move the roof panel switch in any di-
rection.Synchronizing the panorama roof with
power tilt/sliding panel
The tilt/sliding panel must be
synchronized
after the battery has been
disconnected or discharged
after the tilt/sliding panel has been
closed manually (
page 414)
after a malfunction
if the tilt/sliding panel does not open
smoothly
Remove the fuse from the main fuse
box (
page 443).
Reinsert the fuse in the main fuse box.
Switch on the ignition (
page 33).
Move and hold the roof panel switch in
the direction of arrow2 until the roller
sunblinds are fully closed.
Keep holding the roof panel switch in
the direction of arrow2 for approxi-
mately one second.
Move and hold the roof panel switch in
the direction of arrow1 until the roller
sunblinds are fully opened.
Keep holding the roof panel switch in
the direction of arrow1 for approxi-
mately one second.
Page 232 of 506
230 Controls in detailPanorama roof with power tilt/sliding panel*
Move and hold the roof panel switch in
the direction of arrow3 until the
tilt/sliding panel is fully raised.
Keep holding the roof panel switch in
the direction of arrow3 for approxi-
mately one second.
Move and hold the roof panel switch in
the direction of arrow2 until the
tilt/sliding panel is fully closed.
Keep holding the roof panel switch in
the direction of arrow2 for approxi-
mately one second.
Check the Express-open feature of the
tilt/sliding panel (
page 229).
If the tilt/sliding panel opens com-
pletely, the roof is synchronized. Other-
wise repeat the above steps.
Solar panel*
A solar panel is available in combination
with the panorama roof with tilt/sliding
panel. The solar cells convert natural light
into electrical energy. When the engine is
switched off, the energy generated auto-
matically switches on the ventilation fan.
The constant air flow creates a cooler tem-
perature for cars parked in the sunlight.
The air flow depends on the intensity of the
solar radiation. The ventilation starts two
minutes after switching off the engine.
Page 233 of 506
231 Controls in detail
Driving systems
Driving systems
The following driving systems are ex-
plained on the following pages:
Cruise control and Distronic*, with
which the vehicle can maintain a preset
speed
Airmatic* adjusts the vehicle suspen-
sion characteristics automatically and
controls the vehicle level
Parktronic system*, which assists the
driver during parking maneuvers
The BAS, ABS, ESP and SBC are described
in the “Safety and Security” section
(
page 85).
Cruise control
The cruise control automatically maintains
the speed you set for your vehicle.
Use of cruise control is recommended for
driving at a constant speed for extended
periods of time. You can set or resume
cruise control at any speed above 25 mph
(40 km /h).
E 320 4MATIC, E 500 4MATIC:
You can set or resume cruise control at any
speed above 20 mph (30 km /h).
The cruise control function is operated by
means of the cruise control lever.
The cruise control lever is the uppermost
lever found on the left-hand side of the
steering column (
page 22).
Warning!
G
Cruise control is a convenience system de-
signed to assist the driver during vehicle op-
eration. The driver is and must always
remain responsible for the vehicle speed
and for safe brake operation.
Only use cruise control if the road, traffic
and weather conditions make it advisable to
travel at a steady speed.
The use of cruise control can be danger-
ous on winding roads or in heavy traffic
because conditions do not allow safe
driving at a steady speed.
The use of cruise control can be danger-
ous on slippery roads. Rapid changes in
tire traction can result in wheel spin and
loss of control.
Deactivate cruise control when driving
in fog.
The “Resume” function should only be oper-
ated if the driver is fully aware of the previ-
ously set speed and wishes to resume this
particular preset speed.
Page 234 of 506
232 Controls in detailDriving systems1Set current or higher speed
2Set current or lower speed
3Cancel cruise control
4Resume at previously set speed
Setting current speed
Accelerate or decelerate to the desired
speed.
Briefly lift1 or depress2 the cruise
control lever.
The current speed is set.
Remove your foot from the accelerator
pedal.
Cruise control is activated.The selected speed appears in the multi-
function display for approximately five sec-
onds, and the corresponding speedometer
segments from the selected speed to the
vehicle maximum speed are illuminated.
iOn uphill or downhill grades, cruise
control may not be able to maintain the
set speed. Once the grade eases, the
set speed will be resumed.
E 320 CDI, E 320, E 500, E 55 AMG:
On downhill grades, the cruise control
will hold the set speed with active brak-
ing action.
In addition, on longer downhill grades
the automatic transmission will auto-
matically downshift.
E 320 4MATIC, E 500 4MATIC:
If the engine’s braking power does not
brake the vehicle sufficiently on down-
hill grades, the automatic transmission
will automatically downshift.
Page 235 of 506
233 Controls in detail
Driving systems
Canceling cruise control
There are several ways to cancel cruise
control:
Step on the brake pedal.
Cruise control will be canceled. The
last speed set will be stored for later
use.
or
Briefly push the cruise control lever to
position3.
Cruise control will be canceled. The
last speed set will be stored for later
use.iThe last stored speed is canceled when
you turn off the engine.
iCruise control automatically switched
off, if
E 320 CDI, E 320, E 500, E 55 AMG:
you step on the brake pedal.
you depress the parking brake ped-
al.
In this case the segments in the
multifunction display (
page 232)
go out and no warning sounds.
the vehicle speed is below 25 mph
(40 km/h).
the ESP is in operation or switched
off with the ESP switch (
page 89).
you move the gear selector lever to
position N while driving.
The segments in the multifunction dis-
play (page 232) go out, and an
acoustic warning sounds.
E 320 4MATIC, E 500 4MATIC:
you step on the brake pedal.
you move the gear selector lever to
position N while driving.
the vehicle speed is below 20 mph
(30 km/h).
ESP is in operation.
The segments in the multifunction dis-
play are flashing.
!Moving gear selector lever to
positionN while driving also cancels
cruise control. However, the gear se-
lector lever should not be moved to
positionN while driving except to coast
when the vehicle is in danger of skid-
ding (e.g. on icy roads).
Page 236 of 506
234 Controls in detailDriving systemsSetting a higher speed
Lift cruise control lever to position1
and hold it up until the desired speed is
reached.
Release cruise control lever.
The new speed is set.
Setting a lower speed
Depress cruise control lever to
position2 and hold it down until the
desired speed is reached.
Release cruise control lever.
The new speed is set.Fine adjustment in 1 mph
(Canada: 1 km / h) increments
Faster
Briefly tip cruise control lever in direc-
tion of arrow1.
Slower
Briefly tip cruise control lever in direc-
tion of arrow2.Setting to last stored speed
(“Resume” function)
Briefly pull cruise control lever to
position4.
The cruise control resume the last set
speed.
Remove your foot from the accelerator
pedal.
The selected speed appears in the multi-
function display for approximately five sec-
onds, and the corresponding speedometer
segments from the selected speed to the
vehicle maximum speed are illuminated.
iDepressing the accelerator pedal does
not deactivate cruise control. After
brief acceleration (e.g. for passing),
cruise control will resume the last
speed set.
iE 320 CDI, E 320, E 500, E 55 AMG:
When you use the cruise control lever
to decelerate, the brake system will au-
tomatically brake the vehicle if the en-
gine’s braking power does not brake
the vehicle sufficiently.
E 320 4MATIC, E 500 4MATIC:
When you use the cruise control lever
to decelerate, the transmission will au-
tomatically downshift if the engine’s
braking power does not brake the vehi-
cle sufficiently.
Warning!
G
The speed stored in memory should only be
set again if prevailing road conditions per-
mit. Possible acceleration or deceleration
differences arising from returning to the pre-
set speed could cause an accident and/or
serious injury to you and others.
Page 237 of 506
235 Controls in detail
Driving systems
Distronic*
When activated, the Distronic adaptive
cruise control system increases driving
convenience afforded by the cruise control
during travel on expressways and other
major roads.
If the Distronic distance sensor detects
a slower moving vehicle directly ahead,
your vehicle speed will be reduced so
that you follow that vehicle at a preset
distance.
If there is no vehicle directly ahead of
you, Distronic will function in the same
way as cruise control (
page 239).
Warning!
G
Distronic adaptive cruise control is no sub-
stitute for active driving involvement. It does
not react to stationary objects, nor recog-
nize or predict the curvature and lane layout
or the movement of vehicles ahead.
Distronic can only apply a maximum of 20%
of the vehicle’s braking power.
It is the driver’s responsibility at all times to
be attentive to traffic and road conditions
and to provide the steering, braking and oth-
er driving inputs necessary to retain control
of the vehicle.Warning!
G
Distronic is a convenience system. Its speed
adjustment reduction capability is intended
to make cruise control more effective and
usable when traffic speeds vary. However, it
is not intended to, nor does it, replace the
need for extreme care. The responsibility for
the vehicle speed and the distance to the ve-
hicle ahead, including most importantly
brake operation to assure safe stopping dis-
tance, always rests with the driver.
Distronic cannot take street and traffic con-
ditions into account.
Warning!
G
Distronic requires familiarity with its opera-
tional characteristics. We strongly recom-
mend that you review the following
information carefully before operating the
system.iUSA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.
Page 238 of 506
236 Controls in detailDriving systems
iCanada only:
This device complies with RSS-210 of
Industry Canada. Operation is subject
to the following two conditions:
(1) This device may not cause interfer-
ence, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation of the device.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.Warning!
G
Distronic cannot take street and traffic con-
ditions into account. Only use Distronic if
the road, weather and traffic conditions
make it advisable to travel at a steady
speed.
Warning!
G
Use of Distronic can be dangerous on slip-
pery roads. Rapid changes in tire traction
can result in wheel spin and loss of control.
Distronic does not act upon adverse sight
distance conditions. Do not use Distronic
during conditions of fog and heavy rain,
snow or sleet.Warning!
G
Close attention to road and traffic condi-
tions is imperative at all times, regardless of
whether or not Distronic is activated.
Use of Distronic can be dangerous on wind-
ing roads or in heavy traffic because condi-
tions do not allow safe driving at a steady
speed.
Distronic will not react to stationary objects
in the roadway (e.g. a stopped vehicle in a
traffic jam or a disabled vehicle). Distronic
will also not respond to oncoming vehicles.
Switch off Distronic:
when changing from the left to the right
lane if vehicles are moving more slowly
in the left lane
when entering a turn lane or highway off
ramp
in complex driving situations, such as in
highway construction zones
In these situations, Distronic will continue to
maintain the set speed unless deactivated.
Distronic is designed and intended only to
maintain a set speed and keep a set dis-
tance from moving objects in front of it.
Warning!
G
The “Resume” function should only be oper-
ated if the driver is fully aware of the previ-
ously set speed and wishes to resume this
particular preset speed.
Page 239 of 506
237 Controls in detail
Driving systems
Distronic displays in the speedometer
dial
1Set speed
If Distronic is activated, one or two seg-
ments come on around the set speed.1Segments
If Distronic detects a vehicle directly
ahead, the segments from the speed of the
vehicle ahead to the set speed come on.
If Distronic calculates that there is a dan-
ger of collision:
The DTR warning lampl in the in-
strument cluster comes on red.
An intermittent warning sounds.
Immediately brake the vehicle to avoid
a collision.Under no circumstances should the
driver await the intermittent warning
sound before braking. See the follow-
ing warning note.
The intermittent warning sound ceases
and the red DTR warning lampl
goes out when the necessary distance
to the vehicle ahead is again estab-
lished.
iThe vehicle speed displayed on the
speedometer can briefly vary from the
speed setting on the Distronic system.
Page 240 of 506
238 Controls in detailDriving systems
Distronic menu in the control system
In the Distronic menu you can read the cur-
rent settings for Distronic. What appears in
the display depends on whether Distronic
and the distance warning function are
turned on or off.
Press buttonè orÿ repeatedly
until you see one of the following dis-
plays.
Warning!
G
An intermittent warning sounds and the
DTR warning lamp in the instrument cluster
is illuminated if the Distronic system calcu-
lates that the distance to the vehicle ahead
and your vehicle’s current speed indicate
that Distronic will not be capable of slowing
the vehicle sufficiently to maintain the pre-
set following distance, which creates a dan-
ger of a collision.
Immediately brake the vehicle to increase
the distance to the vehicle in front of you.
The warning sound is intended as a final cau-
tion that you have not interceded with your
own braking inputs to avoid a potentially
dangerous situation. Do not wait for the op-
eration of the warning signal to intercede
with your own braking, as that will result in
potentially dangerous emergency braking
which will not always result in an impact be-
ing avoided.
Tailgating increases the risk of an accident.
Warning!
G
Distronic brakes your vehicle with a maxi-
mum deceleration of 6.5 ft / s
2 (2 m / s
2).
This corresponds to about 20% of the maxi-
mum deceleration ability of your vehicle.
Distronic brakes the vehicle in an effort to
restore the preset distance or to maintain
the speed. The brake pedal is automatically
applied as this happens which results in the
brake pedal moving.
Keep driver’s foot area clear at all times, in-
cluding the area under the brake pedal. Ob-
jects stored in this area may impair pedal
movement which could interfere with the
braking ability of the Distronic system.
Do not place your foot under the brake pedal
– your foot could become caught.