MERCEDES-BENZ EQB SUV 2022 Owners Manual

This can, for example, cause seat belts to tear
or f
ail in an accident. 
Never bleach or dye seat belts. To avoid damage to the vehicle, observe the fol-
lo
wing notes on cleaning and care:
Seat belts = Clean with lukewarm and soapy water.
= Do not use chemical cleaning agents.
= Do not dry by heating them to over 80°C or
exposing them to direct sunlight.
Display
= Switch oM the display and let it cool down.
= Clean the surface carefully with a microNbre
cloth and a suitable display care product (TFT-
LCD).
= Do not use any other agents.
Head-up display = Clean with a sos, non-static, lint-free cloth.
= Do not use cleaning agents. Plastic trim
= Clean wit

h a damp microNbre cloth.
= For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
= Do not attach stickers, Nlms or similar materi-
als.
= Do not allow cosmetics, insect repellent or
sun cream to come into contact with the plas-
tic trim.
Real wood and trim elements
= Clean with a microNbre cloth.
= Black piano-lacquer look: Clean with a damp
cloth and soapy water.
= For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
= Do not use solvent-based cleaning agents, pol-
ishes or waxes.
Roof lining
= Clean with a brush or dry shampoo.
Carpet
= Use a carpet and textile cleaning agent recom-
mended for Mercedes-Benz. Steering wheel made of genuine leather or DINA-
MIC A
* NOTE Damag
e caused by wrong cleaners 
Do not use solvent-based cleaning
ag
ents such as tar remover or wheel
cleaner; neither should you use polishes
or waxes. Otherwise you may damage
the Nnish. =
Clean wit
h a damp cloth and 1% soapy water
solution and then wipe with a dry cloth.
= For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
= Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
= Do not allow the leather to become too damp.
= Do not use a microNbre cloth. 318
Maintenance and care

%
Leather is a natural product. It exhibits natural
sur face properties such as diMerences in
structure, marks caused by growth and injury
or subtle colour diMerences. These surface
properties are characteristics of leather and
not material faults. What's more, leather is
subject to a natural ageing process during
which the surface properties change.
Genuine leather seat covers
= V

acuum up dirt such as crumbs or dust and
then clean the seat covers with a damp cotton
cloth and wipe down with a dry cloth. Regu-
larly clean the seat covers.
= For heavy soiling: use a leather care agent rec-
ommended for Mercedes-Benz asercare.
= Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
= Do not use a microNbre cloth.
= Do not allow the leather to become too damp.
= Do not use oil-based cleaning and care prod-
ucts.
% Leather is a natural product. It exhibits natural
sur
face properties such as diMerences in structure, marks caused by growth and injury
or subtle colour diMer

ences. These surface
properties are characteristics of leather and
not material faults. What's more, leather is
subject to a natural ageing process during
which the surface properties change.
Regular cleaning and care of the leather
reduces soiling, wear marks and ageing dam-
age and thus signiNcantly extends its life
span. Clothing that can leave stains (e.g.
jeans) can discolour the leather.
DINAMICA seat covers
= Clean wit

h a damp cloth.
= Do not use a microNbre cloth.
Imitation leather seat covers = Vacuum up dirt such as crumbs or dust and
then use a damp cotton cloth and a 1% soap-
suds solution to clean the entire seat cover.
Do not spot clean.
= Use cleaning and care products recommen-
ded for Mercedes-Benz.
= Do not use a microNbre cloth. =
Do no
t use oil-based cleaning and care prod-
ucts.
Fabric seat covers
= Vacuum up dirt such as crumbs or dust and
then use a damp microNbre cloth and a 1%
soapsuds solution to clean the entire seat
cover. Do not spot clean.
= Use cleaning and care products recommen-
ded for Mercedes-Benz.
= Do not use oil-based cleaning and care prod-
ucts. Maintenance and care
319

Emergency
Removing the safety vest
The safety vests are located in the stowage com-
par
tments in the driver's and front passenger
door. 
Pull out the safety vest bag by the loop. 
Open the safety vest bag and pull out the
saf

ety vest.
% There are also safety vest compartments in
t

he rear door stowage compartments in which
safety vests can be stored. 1
Maximum number of washes
2 Maximum wash temperature 3
Do not bleach
4 Do not iron
5 Do not tumble dry
6 Do not dry clean
7 Class 2 safety vest
The requirements deNned b
y the legal standard
are only fulNlled if the safety vest is the correct
size and is fully closed.
Replace the safety vest in the following cases:
= The reOective strips are damaged or dirty
= The maximum permissible number of washes
is exceeded
= The Ouorescence has faded Warning triangle
Removing the warning triangle
Vehicles with two rows of seats320
Breakdown assistance

Vehicles with three rows of seats

Open the load compartment Ooor .
Remove warning triangle 1. Setting up the warning triangle 
Fold side reOectors 1 upwards to form a tri-
angle and attach at the top using upper press-
stud 2. 
Fold legs 3 do
wn and out to the side. First-aid kit
(sos sided) o
verview Vehicles with two rows of seats
Vehicles with three rows of seats Breakdown assistance
321

First-aid kit
(sos sided) 1 is under t he load com-
partment Ooor. Removing the Nr

e extinguisher &
WARNING Risk of accident due t
o an
incorrectly secured Nre extinguisher in the
driver's footwell
A Nr
e extinguisher may impede pedal travel or
block a depressed pedal.
This jeopardises the operating and road safety
of the vehicle.
The Nre extinguisher can be Oung around and
injure the driver or other vehicle occupants. 
Always store and secure the Nr
e extin-
guisher in the bracket. 
Do not remove the Nr
e extinguisher while
driving. 
Les-hand dr
ive vehicle: pull tab 1 upwards. 
Right-hand drive vehicle: pull t
ab 1 down-
wards. 
Remove Nr
e extinguisher 2. Flat tyre
Notes on Oat
tyr
es &
WARNING Risk of accident due t
o a Oat
tyre
A Oat tyr
e severely aMects the driving charac-
teristics as well as the steering and braking of
the vehicle. Tyres without
r
un-Oat characteristics: 
Do not drive with a Oat tyr
e. 
Change the Oat tyr
e immediately with an
emergency spare wheel or spare wheel.
Alternatively, consult a qualiNed special-
ist workshop.
Tyres with r
un-Oat characteristics: 
Observe the information and warning
no
tes on MOExtended tyres (run-Oat
tyres). In the event of a Oat
tyr
e, the following options are
available depending on your vehicle's equipment:
= Vehicles with MOExtended tyres: it is possible
to continue the journey for a short period of
time. Make sure you observe the notes on
MOExtended tyres (run-Oat tyres)
( page 323).
= Vehicles with a TIREFIT kit: you can repair the
tyre so that it is possible to continue the jour-
ney for a short period of time. To do this, use
the TIREFIT kit ( page 324). 322
Breakdown assistance

=
V ehicles with Mercedes me connect: you can
make a call for breakdown assistance via the
overhead control panel in the case of a break-
down (  page 283).
= All vehicles: change the wheel (  page 349).Notes on MOExtended tyres
(r
un-Oat tyres) &
WARNING Risk of accident when dr
iving in
limp-home mode
Driving in emergency mode impairs the han-
dling c
haracteristics of the vehicle. 
Do not exceed the permissible maximum
speed of t
he MOExtended tyres. 
Avoid any abrupt steering and driving
manoeuvr
es as well as driving over
obstacles (kerbs, pot holes, oM-road).
This applies, in particular, to a loaded
vehicle. 
Stop driving in the emergency mode if
y

ou notice:
= banging noise =
v
ehicle vibration
= smoke which smells like rubber
= continuous ESP n
intervention
= cracks in the tyre sidewalls 
Aser dr
iving in emergency mode, have
the rims checked by a qualiNed specialist
workshop with regard to their further
use. 
The defective tyre must be replaced in
e

very case. With MOExtended tyres
(r
un-Oat tyres), you can
continue to drive your vehicle even if there is a
total loss of pressure in one or more tyres. How-
ever, the tyre aMected must not show any clearly
visible damage.
You can recognise MOExtended tyres by the
MOExtended marking which appears on the side
wall of the tyre.
Vehicles with tyre pressure monitoring system:
MOExtended tyres may only be used in conjunc-
tion with an activated tyre pressure monitoring
system. If a pressure loss warning message appears in the
dr
iver's display, proceed as follows:
= Check the tyre for damage.
= If driving on, observe the following notes.
Driving distance possible in emergency mode
aser the pressure loss warning: Load condition Driving distance possi-
ble in emer
gency mode
Partially laden 80 km
Fully laden 30 km The driving distance possible in emergency mode
ma
y vary depending on the driving style. Observe
the maximum permissible speed of 80 km/h.
If a tyre has gone Oat and cannot be replaced with
an MOExtended tyre, you can use a standard tyre
as a temporary measure. TIREFIT kit storage location
The TIREFIT kit is located under the luggage com-
par
tment Ooor. Breakdown assistance
323

Vehicles with two rows of seats
1
Tyre inOation com pressor
2 Tyre sealant bottle Vehicles with three rows of seats
1
Tyre sealant bottle
2 Tyre inOation com
pressor
Depending on the model, the TIREFIT kit may also
be locat
ed in other places under the boot Ooor.
% You can Nnd inf
ormation on the power cate-
gory (LK) and/or electrical data on the back
of the tyre inOation compressor:
= LK2 !

You can use TIREFIT tyre sealant to seal perfora-
tion damag e of up to 4 mm, particularly those in
the tyre contact surface. You can use TIREFIT in
outside temperatures down to -20 °C. &
WARNING Risk of accident when using
tyr
e sealant
The tyre sealant may be unable to seal the
tyr
e properly, especially in the following cases:
= there are large cuts or punctures in the
tyre (larger than damage previously men-
tioned)
= the wheel rims have been damaged
= aser journeys with very low tyre pressure
or with Oat tyres 
Do not continue driving. 
Consult a q
ualiNed specialist workshop. &
WARNING Risk of injur
y and poisoning
from tyre sealant
Tyre sealant is hazardous to health and causes
ir
ritation. Do not allow it to come into contact with your skin, eyes or clothing, and do not
sw

allow it. Do not inhale any vapours. Keep
the tyre sealant away from children.
Observe the following if you come into contact
with the tyre sealant: 
Rinse oM t
he tyre sealant from your skin
using water immediately. 
If tyre sealant gets into your eyes, thor-
oughl

y rinse them using clean water
immediately. 
If tyre sealant has been swallowed, thor-
oughl
y rinse out your mouth immediately
and drink plenty of water. Do not induce
vomiting and seek medical attention
immediately. 
Change out of clothing which has come
int

o contact with tyre sealant immedi-
ately. 
If an allergic reaction occurs, seek medi-
cal att

ention immediately. *
NOTE Ov
erheating due to the tyre inOation
compressor running too long 
Do not run the tyre inOation com
pressor
for longer than ten minutes without inter-
ruption. Comply with the manufacturer's safety notes on
t

he sticker on the tyre sealant bottle.
Have the tyre sealant bottle replaced in a qualiNed
specialist workshop every Nve years. 
Do not remove any foreign objects which have
ent

ered the tyre. Breakdown assistance
325


Remove sticker 1 fr om the tyre inOation
compressor housing and aPx it to the instru-
ment cluster within the driver's Neld of vision. 
Remove sticker 2 fr
om the tyre sealant bot-
tle and aPx it near the valve on the wheel with
the defective tyre. 
Pull plug 7 wit
h the cable and Nller hose 3
out of the tyre inOation compressor housing. 
Insert tyre sealant bottle 9 in soc
ket 6 of
the tyre inOation compressor in such a way
that the red arrow on tyre sealant bottle 9
matches the red arrow on the tyre inOation
compressor. 
Turn tyre sealant bottle 9 a q
uarter turn
clockwise. 
Insert the plug of Nller hose 3 in soc
ket 5
of tyre sealant bottle 9. 
Turn Nller hose 3 a q
uarter turn clockwise. 
Remove the valve cap from valve A
on the
faulty tyre. 
Screw union nut 4 of Nller hose 3 ont
o
valve A. 
Insert plug 7 int
o a 12!


Press on and oM switc h 8 on the tyre inOa-
tion compressor.
The tyre inOation compressor is switched on.
The tyre is inOated. First, tyre sealant is pum-
ped into the tyre. The pressure may brieOy rise
to approximately 500 kPa (5 bar/73 psi).
Do not switch oM t
he tyre inOation compressor
during this phase! 
Let the tyre inOation com
pressor run for a
maximum of ten minutes.
The tyre should then have attained a tyre pres-
sure of at least 200 kPa (2.0 bar/29 psi).
If tyre sealant leaks out, make sure you clean the
aMect
ed area as quickly as possible. It is prefera-
ble to use clean water.
If you get tyre sealant on your clothing, have it
cleaned as soon as possible with perchloroethy-
lene.
If, aser ten minutes, a tyre pressure of 200 kPa
(2.0 bar/29 psi) has not been attained: 
Switch oM t
he tyre inOation compressor. 
Unscrew the Nlling hose fr
om the valve of the
defective tyre.
Please note that tyre sealant may leak out when
unscr
ewing the Nlling hose. 
Drive forwards or in reverse very slowly for
appr
oximately 10 m. 
Pump up the tyre again.
Aser a maximum of t

en minutes the tyre pres-
sure must be at least 200 kPa (2.0 bar/
29 psi). &
WARNING Risk of accident due t
o the
speciNed tyre pressure not being attained
If the speciNed tyr
e pressure is not attained
aser the speciNed time, the tyre is too badly
damaged. The tyre sealant cannot repair the
tyre in this instance.
The braking and driving characteristics may be
greatly impaired. 
Do not continue driving. 
Consult a q
ualiNed specialist workshop. *
NOTE S
taining from leaking tyre sealant Aser
use, e
xcess tyre sealant may leak out
from the Nlling hose. 
Therefore, place the Nlling hose in t
he
plastic bag that contained the TIREFIT
kit. If, aser
t
en minutes, a tyre pressure of 200 kPa
(2.0 bar/29 psi) has been attained: 
Switch oM t
he tyre inOation compressor. 
Unscrew the Nlling hose fr
om the valve of the
defective tyre.
Please note that tyre sealant may leak out when
unscr
ewing the Nlling hose. &
WARNING Risk of accident fr
om driving
with sealed tyres
A tyre temporarily sealed with tyre sealant
im
pairs the handling characteristics and is not
suitable for higher speeds. Breakdown assistance
327