MERCEDES-BENZ EQC SUV 2022 Owners Manual

If
th e battery is insu1cient lych arge d, the stand-
ing lights or parking lights will be switched o.
automatically tofacilitate the next drive system
start.
The exterior lighting (e xcept standing and parking
lights) will switch o. automatically when the driv-
er's door is opened.
R Obser vethe no tes on sur round lighting
(/ page 133).
A A ut
ut omatic dr
omatic dr iving lights function
iving lights function
When theve hicle is switched on, the standing
lights, low beam and daytime running lights are
switched on automatically depending on the light
conditions. &
W
W ARNING
ARNING Risk of accident when the
dipped beam is switched o. in poor visi-
bility
When the light switch is set toà ,the
dipped beam may not be switched on auto-
matically if there is fog, snow or other causes
of poor visibility such as spr ay. #
In such cases, turn the light switch to
L . The automatic driving lights are only an aid.
Yo u
are responsible forve hicle lighting.
Switc
Switc hing t
hing t he r
he rear f
ear f og light
og light on/o.
on/o.
R
R eq
eq uir
uir ements:
ements:
R The light switch is in the L orà posi-
tion. #
Press button R.
Please obser vethe count ry-speci/c la wsonthe
use of rear fog lamps. Oper
Oper
ating t
ating t he combination switc
he combination switc h f
h for t
or t he lights
he lights 1
High beam
2 Turn signal light, right
3 Headlamp 0ashing
4 Turn signal light, leT #
Use the combination switch toselect the
desired function. 128
128
Light and sight

Switc
Switc
hing on high beam
hing on high beam #
Turn the light switch totheL orÃ
position. #
Push the combination switch be yond the point
of resis tance in the direction of ar row 1.
When the high beam is activated, the indicator
lamp for low beam Lwill be deactivated
and replaced bythe indicator lamp for high
beam K.
Switc
Switc hing
hingo.
o.high beam
high beam #
Movethe combination switch back toits start-
ing position.
Headlam
Headlam p
p0ashing
0ashing #
Pull the combination switch in the direction of
ar ro w 3.
T
T ur
ur n signal light
n signal light #
T To indicat
o indicat e
ebr
br ie0y:
ie0y: push the combination
switch brie0y tothe point of resis tance in the
direction of ar row 2 or4.
The cor responding turn signal light will 0ash
th re e times. #
T
To indicat o indicat e per
e permanentl y:
manent ly:push the combina-
tion switch be yond the point of resistance in
th e direction of ar row 2 or4. A
A
ctiv
ctiv ating/deactiv
ating/deactiv ating t
ating the hazar
he hazar d w
d war
arning lights
ning lights #
Press button 1. The hazard
warning lights will switch on automati-
cally if:
R the airbag has been deplo yed.
R theve hicle is braked heavily from a speed of
more than 70 km/h toa standstill.
When you pull away again, the hazard warning
light system will switch o. automatically at
appr oximately 10 km/h. You can also switch o.
th e hazard warning light system using button 1. A
A
dap
dap tiv
tive functions, MUL
e functions, MUL TIBEAM LED
TIBEAM LED Int
Int
ellig
ellig ent Light Syst
ent Light Syst em function
em function
The MULTIBEAM LED headlamp s adapttothe
driving and weather situation and pr ovide exten-
ded functions for impr oved illumination of the
ro ad.
The system comprises thefo llowing functions:
R Active headlamps (/ page 130)
R Cornering light (/ page 130)
R Motorw ay mode (/ page 130)
R City lighting (/ page 131) Light and sight
129
129

Syst
Syst
em limits
em limits
R The system is active only when it is da rk.
A
A ctiv
ctiv e headlam
e headlamps function ps function R
When the high beam is switched on, the head-
lamps follow the steering mo vements.
R When the low beam is switched on: the cor-
nering light is automatically activated on tight
bends tofur ther illuminate releva nt areas.
Depending on theve hicle's equipment, the course
of the lane in which you are driving will also be
ev aluated and the active headlamps function will
adjust the light in advance. Cor
Cor ner
nering light function
ing light function The cornering light impr
ovesth e illumination of
th e car riag ewa yove r a wide angle in the turning
direction, enabling better visibility on tight bends,
fo rex ample. The cornering light can be activated
only when the low beam is switched on.
The function is active in thefo llowing cases:
R Atspeeds below 40 km/h when the turn sig-
nal light is switched on or the steering wheel
is turned
R Atspeeds between 40 km/h and 70 km/h
and when the steering wheel is turned R
R
oundabout and junction function:
oundabout and junction function: the cornering
light will be activated on bo thsides based on an
ev aluation of theve hicle's cur rent GPS position. It
will remain active until aTer theve hicle has leT
th ero undabout or the junction.
Mot
Mot orwa
or wa y mode function
y mode function
Mo torw ay mode increases thera nge and bright-
ness of the cone of light, enabling better visibility. The function will be active if a mo
torw ay journey
is de tected bymeans of:
R theve hicle's speed
R the multifunction camera
R the GPS 130
130
Light and sight

The function is not active in
thefo llowing cases:
R at speeds below 80 km/h
The city lighting function
The city lighting function
City lighting impr ovesth e illumination of roadsides
in urban areas using a broad distribution of light.
The function is active in thefo llowing cases:
R Atlow speeds
R In illuminated parts of urban areas
Switc Switc hing t hing t he Int
he Int ellig
elligent Light Syst
ent Light Syst em
emon/o.
on/o.
R
R eq
eq uir
uir ements:
ements:
R The vehicle is switched on.
Multimedia system: 4 © 5
Settings 5
Lights
5 Intelligent Light System #
Activate or deactivate the function. A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assist Plus t Plus A
A
dap
dap tiv
tive Highbeam Assis
e Highbeam Assist Plus function t Plus function &
W
WARNING
ARNING Risk of accident despite Adap-
tive Highbeam Assist Plus
Ad aptive Highbeam Assist Plus does not react
to:
R road users without lights, e.g. pedestrians
R road users with poor lighting, e.g. cyclists
R road users whose lighting is obstructed,
e.g. bya bar rier
On very rare occasions, Adaptive Highbeam
Assist Plus may failto recognise other road
users with their own lighting, or may recognise
th em too late.
In these, or in similar situations, the automatic
high beam will not be deactivated or will be
activated despite the presence of other road
users. #
Always obser vethero ad and tra1c con-
ditions carefully and switch o. the high
beam in good time. Ad
aptive Highbeam Assist Plus cann ottake into
account road, weather or tra1c conditions.
De tection may be restric ted in thefo llowing
cases:
R In poor visibility, e.g. fog, heavy rain or snow
R Ifth ere is dirt on the sensors or the sensors
are obscured
Ad aptive Highbeam Assist Plus is only an aid. Yo u
are responsible for adjusting theve hicle's lighting
to the pr evailing light, visibility and tra1c condi-
tions. Light and sight
131 131

Ad
aptive Highbeam Assist Plus automatically
switches between thefo llowing types of light:
R Low beam
R Partial high beam
R High beam
Pa rtial high beam uses the high beam toshine
past other road users rather than dazzling them. The
vehicle in front will be illuminated bythe low
beam.
At speeds greater than 30 km/h:
R If no other road users are de tected, the high
beam will switch on automaticall y.
R Ifot her road users are de tected, the partial
high beam will switch on automaticall y.
At speeds below 25 km/h or when there is su1-
cient street lighting:
R The partial high beam will switch o. automati-
cally.
R The high beam will switch o. automaticall y.
At speeds greater than appr oximately 50 km/h:
R The headlamp range of the low beam is regu-
lated automatically based on the distance to
ot her road users.
% The system's optical sensor is located behind
th e windscreen near theove rhead control
panel. Switc Switc
hing A hing A dap
daptiv
tive Highbeam Assis
e Highbeam Assist Plus t Pluson/o.
on/o.
Switc
Switc hing on
hing on #
Turn the light switch totheà position. #
Switch on the high beam using the combina-
tion switch.
When the high beam is switched on automati-
cally in the dar k, the_ indicator lamp will
light up on the central display section of the
inst rument displa y.
Switc Switc hing
hingo.
o. #
Switch o. the high beam using the combina-
tion switch. Se
Se
tting t
tting t he e
he ext
xter
er ior lighting
ior lighting switc
switch-o.
h-o. dela
delay time
y time R
R
eq
eq uir
uir ements:
ements:
R The light switch is in theà position. 132
132
Light and sight

Multimedia system:
4 © 5
Settings 5
Lights
5 Ext. light. del. sw. off #
Set the swit ch-o. delay time.
When theve hicle's engine is switched o., the
ex terior lighting will be activated forth e set
time. Switc
Switc
hing t
hing t he surr
he surr ound lighting
ound lighting on/o.
on/o. Multimedia system:
4 © 5
Settings 5
Lights
5 Surround lighting
When Surround lighting is active,theex terior
lighting lights up for 40 seconds aTer theve hicle
is unloc ked. When you start theve hicle, the sur-
ro und lighting is deactivated and the automatic
driving lights are activated. #
Activate or deactivate the function. Int
Int
er
erior lighting
ior lighting A
A
djus
djus ting t
ting t he int
he int er
erior lighting
ior lighting F
F
r
ront ov
ont overerhead contr
head contr ol panel
ol panel 1
p Front leT reading lamp
2 | Automatic interior lighting control
3 c Front interior lighting
4 u Rear interior lighting
5 p Front right reading lamp #
T
To switc
o switc h on or
h on or o.:
o.:press but ton1 –5
accordingl y. Contr Contr
ol panel in t ol panel in t hegr
he grab handle
ab handle 1
p Rear reading lamp #
T
To switc
o switc h on or
h on or o.:
o.:press the1 button. Light and sight
133
133

Contr
Contr
ol panel in t
ol panel in t he r
he rear passeng
ear passeng er com
er com par
partment
tment 1
p Rear reading lamp #
T
To switc
o switc h on or
h on or o.:
o.:press the1 button. A
A
djus
djus ting t
ting t he ambient lighting
he ambient lighting Multimedia system:
4 © 5
Comfort 5
Ambient lighting
Se
Se tting t
tting t he colour
he colour #
Select Colour. #
Set the desired colour.
A
A djus
djus ting t
ting t he br
he br ightness
ightness #
Select Brightness. #
Adjust the brightness.
A
A ctiv
ctiv ating t
ating t he br
he br ightness f
ightness f or zones
or zones #
Select Brightness. #
Select Brightness zones. #
Activate or deactivate the function.
or #
Set the brightness forth e desired zones.
A
A ctiv
ctiv ating multi-colour
ating multi-colour ed lighting
ed lighting #
Select Colour. #
Select Multi-colour. #
Select a colour combination. A
A
ctiv
ctiv ating multi-colour
ating multi-colour ed animation
ed animation #
Select Colour. #
Select Multi-colour animat..
The chosen colour combination will change at
prede/ned inter vals.
A
A ctiv
ctiv ating w
ating w elcome lighting
elcome lighting #
Select Colour. #
Select Welcome.
When theve hicle is unloc ked, a special ambi-
ent lighting sequence will run.
A
A ctiv
ctiv ating t
ating t he c
he charg
harg e visualisation
e visualisation #
Select Colour. #
Select charge visualisation.
The ambient lighting pr ovides visual feedback
on the di.erent states of charge when the
ve hicle is connected toor disconnected from
th ech arging station.
A
A ctiv
ctiv ating dependency on air conditioning se
ating dependency on air conditioning se t-
t-
tings
tings #
Select Colour. 134
134
Light and sight

#
Select Climate .
If ch anges are made tothete mp erature set-
ting in theve hicle, the colour of the ambient
lighting will change brie0y. Switc
Switc
hing t
hing t he int
he inter
erior lighting
ior lighting switc
switch-o.
h-o. delay
delay
time
time on/o.
on/o. Multimedia system:
4 © 5
Settings 5
Lights
5 Int. light. del. sw. off #
Switch the swit ch-o. delay time on or o..
When this function is active, the interior light-
ing lights up for a short time aTer theve hicle
is loc ked. W
W
indscr
indscr een wiper
een wiper s and windscr
s and windscr een w
een washer sy
asher sy s-
s-
t
t em
em Switc
Switc
hing t
hing t he windscr
he windscr een wiper
een wipers
son/o.
on/o. 1
gWindsc reen wipers o.
2 Ä Intermittent wiping, normal
3 Å Intermittent wiping, frequent 4
° Continuous wiping, slow
5 ¯ Continuous wiping, fast #
Turn the combination switch tothe cor re-
sponding position 1-5. #
Single wipe/w
Single wipe/w ashing:
ashing:pushthe button on the
combination switch in the direction of ar row
1 .
R í Single wipe
R î Wipes with washer 0uid
% Obser vethe no tes on washing theve hicle in a
car wash (/ page 308). Light and sight
135
135

Switc
Switc
hing t
hing t he r
he rear windo
ear windo w wiper
w wiperon/o.
on/o. 1
b Wipes with washer 0uid
2 ° Switches on intermittent wipe
3 gSwitches o. intermittent wipe
4 b Wipes with washer 0uid #
Turn switch 1è tothe cor rect position
1 -4.
The è symbol will appear on the inst ru-
ment display when there ar wind owwiper is
switched on. R
R
eplacing t
eplacing t he windscr
he windscr een wiper blades
een wiper blades &
W
WARNING
ARNING Risk of becoming trapped if the
windscreen wipers are switched on while
wiper blades are being replaced
If th e windscreen wipers begin tomo vewhile
yo u are changing the wiper blades, you can be
trapped bythe wiper arm. #
Always switch o. the windscreen wipers
and vehicle before changing the wiper
blades. Mo Mo
ving t
ving t he wiper ar
he wiper ar ms int
ms into t
o the r
he r eplacement posi-
eplacement posi-
tion
tion #
Switch theve hicle on and then o. again
immediatel y. #
Within around 15 seconds, press and hold the
î button on the combination switch for
appr oximately thre e seconds (/ page 135).
The wiper arms will mo veinto there placement
position.
R R emo
emo ving t
ving t he wiper blades
he wiper blades #
Foldthe wiper arms away from the wind-
screen. 136
136
Light and sight

#
Hold the wiper arm with one hand. With the
ot her hand, turn the wiper blade away from
th e wiper arm in the direction of ar row 1 as
fa r as it will go. #
Slide catch 2inthe direction of ar row 3
until it engages in there mo val position. #
Remo vethe wiper blade from the wiper arm in
th e direction of ar row 4. F
F
itting t
itting t he wiper blades
he wiper blades #
Insert the new wiper blade into the wiper arm
in the direction of ar row 1. #
Slide catch 2inthe direction of ar row 3
until it engages in the locking position. #
Make sure that the wiper blade is seated cor-
re ctl y. #
Foldthe wiper arms back onto the wind-
screen. #
Switch on theve hicle. #
Press theî button on the combination
switch (/ page 135).
The wiper arms will return totheir original
positions. #
Switch o. theve hicle.
% Check the condition of the wiper blades regu-
lar lyand replace them in theev ent of visible
damage or ongoing smearing. Light and sight
137
137