MERCEDES-BENZ GLB SUV 2022 Owners Manual

-
W eather conditions
- Stone chippings and dirt
- Chemical cleaning agents
- Oily products
= Do not use polish on matt decorative foil. Pol-
ishing will have the eMect of shining the foil-
wrapped surface.
= Do not treat matt or structured decorative
foils with wax. Permanent stains may occur.
Scratches, corrosive deposits, areas aMected by
corrosion and damage caused by incorrect care
cannot always be completely repaired. In this
case, contact a qualiNed specialist workshop.
You can obtain more information on care and
cleaning agents from the manufacturer.
In the case of foil-wrapped surfaces, optical diMer-
ences may occur between the surfaces that were
not protected by a decorative foil aser removing a
decorative foil.
% Have work or repairs to decorative foils car-
r
ied out at a qualiNed specialist workshop
(e.g. in a Mercedes-Benz Service Centre). Notes on care of car parts
&
WARNING Risk of entr
apment if the wind-
screen wipers are switched on while the
windscreen is being cleaned
If the windscreen wipers are set in motion
while y
ou are cleaning the windscreen or
wiper blades, you can be trapped by the wiper
arm. 
Always switch oM t
he windscreen wipers
and the vehicle before cleaning the wind-
screen or wiper blades. To avoid damage to the vehicle, observe the notes
on cleaning and car

e of the following car parts:
Wheels and rims
= Use water and acid-free alloy wheel cleaners.
= Do not use acidic alloy wheel cleaners to
remove brake dust. This could damage wheel
bolts and brake components.
= To avoid corrosion of the brake disks and
brakepads, drive the vehicle for a few minutes
aser cleaning before parking it. The brake
disks and brakepads warm up and dry out. Windows
=
Clean t

he windows inside and outside with a
damp cloth and with a cleaning agent recom-
mended for Mercedes-Benz.
= Do not use dry cloths or abrasive or solvent-
based cleaning agents to clean the inside of
windows.
% Aser c
hanging the wiper blades or treating
the vehicle with wax, clean the windscreen
thoroughly with cleaning agents recommen-
ded for Mercedes-Benz. Failure to observe the
application instructions may result in damage,
smear marks or dazzling spots.
% Remove external fogging or dirt on the wind-
scr

een in front of the multifunction camera.
Otherwise, driving systems and driving safety
systems may be impaired or not available
(  page 201).
Wiper blades
= Mo

ve the wiper arms into the replacement
position (  page 155).
= With the wiper arms folded out, clean the
wiper blades with a damp cloth. 328
Maintenance and care

%
Make sure that the wiper blades are coated.
The coating can lea
ve residues on a cloth. Do
not rub the wiper blades excessively or clean
them too osen.
Exterior lighting = Clean t

he lenses with a wet sponge and mild
cleaning agent (e.g. car shampoo).
= Only use cleaning agents or cleaning cloths
that are suitable for plastic lenses.
Sensors = Clean the sensors in the front and rear bump-
ers with a sos cloth and car shampoo
( page 201).
= When using a high-pressure cleaner, maintain
a minimum distance of 30 cm.
Reversing camera and 360° camera = Use clean water and a sos cloth to clean the
camera lens.
= Do not use a high-pressure cleaner.
Trailer hitch
= Observe the notes on care in the trailer hitch
manufacturer's operator manual. =
Do no
t clean the ball neck with a high-pres-
sure cleaner or solvent.
= Remove traces of rust on the ball (e.g. using a
wire brush).
= Remove dirt with a lint-free cloth.
= Aser cleaning, lightly oil or grease the ball
head.
% Before using trailers with anti-torsional cou-
pling, obser

ve the manufacturer's operator
manual. Notes on care of the interior
&
WARNING Risk of injur
y from plastic parts
breaking oM aser the use of solvent-based
care products
Care and cleaning products containing sol-
v
ents can cause surfaces in the cockpit to
become porous. When the airbags are
deployed, plastic parts may break away. 
Do not use any care or cleaning products
cont

aining solvents to clean the cockpit. &
WARNING Risk of injur
y or fatal injuries
from bleached seat belts
Bleaching or dyeing seat belts can severely
w
eaken them.
This can, for example, cause seat belts to tear
or fail in an accident. 
Never bleach or dye seat belts. To avoid damage to the vehicle, observe the fol-
lo
wing notes on cleaning and care:
Seat belts = Clean with lukewarm and soapy water.
= Do not use chemical cleaning agents.
= Do not dry by heating them to over 80°C or
exposing them to direct sunlight.
Display
= Switch oM the display and let it cool down.
= Clean the surface carefully with a microNbre
cloth and a suitable display care product (TFT-
LCD).
= Do not use any other agents. Maintenance and care
329

Head-up display
= Clean wit
h a sos, non-static, lint-free cloth.
= Do not use cleaning agents.
Plastic trim
= Clean with a damp microNbre cloth.
= For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
= Do not attach stickers, Nlms or similar materi-
als.
= Do not allow cosmetics, insect repellent or
sun cream to come into contact with the plas-
tic trim.
Real wood and trim elements
= Clean with a microNbre cloth.
= Black piano-lacquer look: Clean with a damp
cloth and soapy water.
= For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
= Do not use solvent-based cleaning agents, pol-
ishes or waxes.
Roof lining
= Clean with a brush or dry shampoo. Carpet
=
Use a car
pet and textile cleaning agent recom-
mended for Mercedes-Benz.
Steering wheel made of genuine leather or DINA-
MICA
* NOTE Damag
e caused by wrong cleaners 
Do not use solvent-based cleaning
ag
ents such as tar remover or wheel
cleaner; neither should you use polishes
or waxes. Otherwise you may damage
the Nnish. =
Clean wit
h a damp cloth and 1% soapy water
solution and then wipe with a dry cloth.
= For heavy soiling: Use a cleaning agent recom-
mended for Mercedes-Benz.
= Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
= Do not allow the leather to become too damp.
= Do not use a microNbre cloth.
% Leather is a natural product. It exhibits natural
sur
face properties such as diMerences in structure, marks caused by growth and injury
or subtle colour diMer

ences. These surface
properties are characteristics of leather and
not material faults. What's more, leather is
subject to a natural ageing process during
which the surface properties change.
Genuine leather seat covers
= V

acuum up dirt such as crumbs or dust and
then clean the seat covers with a damp cotton
cloth and wipe down with a dry cloth. Regu-
larly clean the seat covers.
= For heavy soiling: use a leather care agent rec-
ommended for Mercedes-Benz asercare.
= Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
= Do not use a microNbre cloth.
= Do not allow the leather to become too damp.
= Do not use oil-based cleaning and care prod-
ucts. 330
Maintenance and care

%
Leather is a natural product. It exhibits natural
sur face properties such as diMerences in
structure, marks caused by growth and injury
or subtle colour diMerences. These surface
properties are characteristics of leather and
not material faults. What's more, leather is
subject to a natural ageing process during
which the surface properties change.
Regular cleaning and care of the leather
reduces soiling, wear marks and ageing dam-
age and thus signiNcantly extends its life
span. Clothing that can leave stains (e.g.
jeans) can discolour the leather.
DINAMICA seat covers
= Clean wit

h a damp cloth.
= Do not use a microNbre cloth.
Imitation leather seat covers = Vacuum up dirt such as crumbs or dust and
then use a damp cotton cloth and a 1% soap-
suds solution to clean the entire seat cover.
Do not spot clean.
= Use cleaning and care products recommen-
ded for Mercedes-Benz.
= Do not use a microNbre cloth. =
Do no
t use oil-based cleaning and care prod-
ucts.
Fabric seat covers
= Vacuum up dirt such as crumbs or dust and
then use a damp microNbre cloth and a 1%
soapsuds solution to clean the entire seat
cover. Do not spot clean.
= Use cleaning and care products recommen-
ded for Mercedes-Benz.
= Do not use oil-based cleaning and care prod-
ucts. Maintenance and care
331

Emergency
Removing the safety vest
The safety vests are located in the stowage com-
par
tments in the driver's and front passenger
door. 
Pull out the safety vest bag by the loop. 
Open the safety vest bag and pull out the
saf

ety vest.
% There are also safety vest compartments in
t

he rear door stowage compartments in which
safety vests can be stored. 1
Maximum number of washes
2 Maximum wash temperature 3
Do not bleach
4 Do not iron
5 Do not tumble dry
6 Do not dry clean
7 Class 2 safety vest
The requirements deNned b
y the legal standard
are only fulNlled if the safety vest is the correct
size and is fully closed.
Replace the safety vest in the following cases:
= The reOective strips are damaged or dirty
= The maximum permissible number of washes
is exceeded
= The Ouorescence has faded Warning triangle
Removing the warning triangle

Open the load compartment Ooor
. 
Remove warning triangle 1. 332
Breakdown assistance

Setting up the warning triangle

Fold side reOectors 1 upwards to form a tri-
angle and attach at the top using upper press-
stud 2. 
Fold legs 3 do
wn and out to the side. First-aid kit
(sos sided) o
verview First-aid kit
(sos sided) 1 is under t
he load com-
partment Ooor. Removing the Nr

e extinguisher &
WARNING Risk of accident due t
o an
incorrectly secured Nre extinguisher in the
driver's footwell
A Nr
e extinguisher may impede pedal travel or
block a depressed pedal. This jeopardises the operating and road safety
of t

he vehicle.
The Nre extinguisher can be Oung around and
injure the driver or other vehicle occupants. 
Always store and secure the Nr
e extin-
guisher in the bracket. 
Do not remove the Nr
e extinguisher while
driving. 
Les-hand dr
ive vehicle: pull tab 1 upwards. 
Right-hand drive vehicle: pull t
ab 1 down-
wards. 
Remove Nr
e extinguisher 2. Breakdown assistance
333

Flat tyre
Notes on Oat
tyr es&
WARNING Risk of accident due t
o a Oat
tyre
A Oat tyr
e severely aMects the driving charac-
teristics as well as the steering and braking of
the vehicle.
Tyres without run-Oat characteristics: 
Do not drive with a Oat tyr
e.
Change the Oat tyr
e immediately with an
emergency spare wheel or spare wheel.
Alternatively, consult a qualiNed special-
ist workshop.
Tyres with r
un-Oat characteristics:
Observe the information and warning
no
tes on MOExtended tyres (run-Oat
tyres). In the event of a Oat
tyr
e, the following options are
available depending on your vehicle's equipment:
= Vehicles with MOExtended tyres: it is possible
to continue the journey for a short period of
time. Make sure you observe the notes on
MOExtended tyres (run-Oat tyres)
( page 334).
= Vehicles with a TIREFIT kit: you can repair the
tyre so that it is possible to continue the jour-
ney for a short period of time. To do this, use
the TIREFIT kit ( page 336).
= Vehicles with Mercedes me connect: you can
make a call for breakdown assistance via the
overhead control panel in the case of a break-
down (  page 292).
= All vehicles: change the wheel (  page 362). Notes on MOExtended tyres
(r
un-Oat tyres) &
WARNING Risk of accident when dr
iving in
limp-home mode
Driving in emergency mode impairs the han-
dling c
haracteristics of the vehicle. 
Do not exceed the permissible maximum
speed of t
he MOExtended tyres. 
Avoid any abrupt steering and driving
manoeuvr
es as well as driving over
obstacles (kerbs, pot holes, oM-road).
This applies, in particular, to a loaded
vehicle. 
Stop driving in the emergency mode if
y

ou notice:
= banging noise
= v

ehicle vibration
= smoke which smells like rubber
= continuous ESP n
intervention
= cracks in the tyre sidewalls 
Aser dr
iving in emergency mode, have
the rims checked by a qualiNed specialist
workshop with regard to their further
use. 
The defective tyre must be replaced in
e

very case. 334
Breakdown assistance

With MOExtended tyres
(r un-Oat tyres), you can
continue to drive your vehicle even if there is a
total loss of pressure in one or more tyres. How-
ever, the tyre aMected must not show any clearly
visible damage.
You can recognise MOExtended tyres by the
MOExtended marking which appears on the side
wall of the tyre.
Vehicles with tyre pressure loss warning system:
MOExtended tyres may only be used in conjunc-
tion with an activated tyre pressure loss warning
system.
Vehicles with tyre pressure monitoring system:
MOExtended tyres may only be used in conjunc-
tion with an activated tyre pressure monitoring
system.
If a pressure loss warning message appears in the
driver's display, proceed as follows:
= Check the tyre for damage.
= If driving on, observe the following notes. Driving distance possible in emergency mode
aser t
he pressure loss warning: Load condition Driving distance possi-
ble in emer
gency mode
Partially laden 80 km
Fully laden 30 km The driving distance possible in emergency mode
ma
y vary depending on the driving style. Observe
the maximum permissible speed of 80 km/h.
If a tyre has gone Oat and cannot be replaced with
an MOExtended tyre, you can use a standard tyre
as a temporary measure. Storage location of the TIREFIT kit (not plug-in
h

ybrid) The TIREFIT kit is located under the load compart-
ment Ooor

. 1
Tyre inOation com
pressor
2 Tyre sealant bottle
Depending on the vehicle version, the TIREFIT kit
ma
y also be located in other places under the
load compartment Ooor.
% You can Nnd inf
ormation on the power cate-
gory (LK) and/or electrical data on the back
of the tyre inOation compressor:
= LK2 !

At a distance of approximately 1 m to the tyre
inOation com
pressor and approximately 1.6 m
above the ground, the following sound pres-
sure levels apply:
= Emission sound pressure level L
PA 83 dB
(A)
= Sound power level L
WA 91 dB (A)
The tyre inOation compressor is maintenance-
free. If there is a malfunction, please contact
a qualiNed specialist workshop. Using the TIREFIT kit
Required tools:
=
T

yre sealant bottle
= TIREFIT sticker
= Sticker with details of the maximum permissi-
ble speed
= Tyre inOation compressor
= Gloves
TIREFIT kit storage location: ( page 335) You can use TIREFIT tyre sealant to seal perfora-
tion damag
e of up to 4 mm, particularly those in
the tyre contact surface. You can use TIREFIT in
outside temperatures down to -20 °C. &
WARNING Risk of accident when using
tyr
e sealant
The tyre sealant may be unable to seal the
tyr
e properly, especially in the following cases:
= there are large cuts or punctures in the
tyre (larger than damage previously men-
tioned)
= the wheel rims have been damaged
= aser journeys with very low tyre pressure
or with Oat tyres 
Do not continue driving. 
Consult a q
ualiNed specialist workshop. &
WARNING Risk of injur
y and poisoning
from tyre sealant
Tyre sealant is hazardous to health and causes
ir
ritation. Do not allow it to come into contact with your skin, eyes or clothing, and do not
sw

allow it. Do not inhale any vapours. Keep
the tyre sealant away from children.
Observe the following if you come into contact
with the tyre sealant: 
Rinse oM t
he tyre sealant from your skin
using water immediately. 
If tyre sealant gets into your eyes, thor-
oughl

y rinse them using clean water
immediately. 
If tyre sealant has been swallowed, thor-
oughl
y rinse out your mouth immediately
and drink plenty of water. Do not induce
vomiting and seek medical attention
immediately. 
Change out of clothing which has come
int

o contact with tyre sealant immedi-
ately. 
If an allergic reaction occurs, seek medi-
cal att

ention immediately. 336
Breakdown assistance

*
NOTE Overheating due to the tyre inOation
compressor running too long 
Do not run the tyre inOation com
pressor
for longer than ten minutes without inter-
ruption. Comply with the manufacturer's safety notes on
t

he sticker on the tyre sealant bottle.
Have the tyre sealant bottle replaced in a qualiNed
specialist workshop every Nve years.
Do not remove any foreign objects which have
ent

ered the tyre. 
Remove sticker 1 fr
om the tyre inOation
compressor housing and aPx it to the instru-
ment cluster within the driver's Neld of vision. 
Remove sticker 2 fr
om the tyre sealant bot-
tle and aPx it near the valve on the wheel with
the defective tyre. 
Pull plug 7 wit
h the cable and Nller hose 3
out of the tyre inOation compressor housing. 
Insert tyre sealant bottle 9 in soc
ket 6 of
the tyre inOation compressor in such a way
that the red arrow on tyre sealant bottle 9
matches the red arrow on the tyre inOation
compressor. Breakdown assistance
337