light MERCEDES-BENZ M-CLASS 2007 Service Manual

102 Safety and SecurityDriving safety systems4-ETS
The 4-Electronic Traction System (4-ETS)
improves the vehicle’s ability to utilize
available traction, especially under
slippery road conditions. The brakes are
applied to the spinning wheel and power is
transferred to the wheel(s) with traction.
The ESP
® warning lampv in the instru-
ment cluster, starts to flash at any vehicle
speed, as soon as a tire loses traction and
the wheel begins to spin.
For more information, see the “Practical
hints” section (
page 414) and
(
page 428).
Off-road - 4-ETS
With the off-road driving program switched
on (page 268), the 4-ETS designed for
off-road use is automatically activated.
i
If conditions require, switch on off-road
driving program (
page 268).
Warning!
G
When you see ESP
® warning lampv
flashing in the instrument cluster, then pro-
ceed as follows:


While driving off, apply as little throttle
as possible.


While driving, ease up on the accelera-
tor.


Adapt your speed and driving style to
the prevailing road conditions.
Failure to observe these guidelines could
cause the vehicle to skid.
The 4-ETS cannot prevent accidents resul-
ting from excessive speed.
!
Operational or performance test must only
be conducted on a two-axle dynanometer. If
such tests are necessary, contact an authorized
Mercedes-Benz Light Truck Center. You could
otherwise seriously damage the brake system or
the transfer case which is not covered by the
Mercedes-Benz Limited Warranty.
!
Because the ESP
® operates automatically,
the engine and ignition must be shut off
(SmartKey in starter switch position0 or1 or
KEYLESS-GO* start/stop button in
position0or1) when testing the brakes on a
brake test dynamometer and such testing should
be no longer than 10 seconds.
Active braking action through the ESP
® may
otherwise seriously damage the brake system
which is not covered by the Mercedes-Benz
Limited Warranty.
i
If the yellow ESP
® warning lampv
comes on while driving, the 4-ETS is being
switched off temporarily to prevent overheating
of the drive wheel brakes. In addition, the
message
ESP inoperative See Operator’s
Manual appears in the multifunction display.
ProCarManuals.com

103 Safety and Security
Anti-theft systems
Anti-theft systems
Immobilizer
The immobilizer prevents unauthorized
persons from starting your vehicle.
Activating
With the SmartKey
Remove the SmartKey from the starter
switch.
With KEYLESS-GO*

Press the KEYLESS-GO start/stop
button (
page 41) on the starter
switch once.
The engine is turned off.

Open the driver’s door.Deactivating
With the SmartKey

Turn the SmartKey in the starter switch
to position2 (
page 39).
With KEYLESS-GO*

Switch on the ignition (
page 40).
Anti-theft alarm system
Once the alarm system has been armed, a
visual and audible alarm is triggered when
someone opens

a door


the tailgate


the hood
The alarm will stay on, even if the activat-
ing element (a door, for example) is imme-
diately closed.
The alarm system will also be triggered
when


the vehicle is opened with the mechan-
ical key, see “Unlocking the vehicle”
(page 475)


a door is opened from the inside, see
“Opening the doors from the inside”
(page 118)
i
Starting the engine will also deactivate the
immobilizer.
In case the engine cannot be started (yet the
vehicle’s battery is charged), the system is not
operational. Contact an authorized
Mercedes-Benz Light Truck Center or call
1-800-FOR-MERCedes (in the USA), or
1-800-387-0100 (in Canada).
ProCarManuals.com

107 Controls in detail
Locking and unlocking
Seats
Memory function*
Lighting
Instrument cluster
Control system
Automatic transmission
Transfer case
Good visibility
Climate control
3-zone automatic climate control*
Power windows
Power tilt/sliding sunroof*
Driving systems
Loading
Useful features
ProCarManuals.com

110 Controls in detailLocking and unlockingGlobal locking
Press button‹.
With the tailgate and all doors closed,
the turn signal lamps flash three times.
The locking knobs in the doors move
down. The anti-theft alarm system is
armed.
Selective setting
If you frequently travel alone, you may wish
to reprogram the SmartKey so that
pressing buttonΠonly unlocks the
driver’s door and the fuel filler flap.

Press and hold buttonsŒ and‹
simultaneously for about 5 seconds
until battery check lamp5
(page 108) flashes twice.
The SmartKey will then function as
follows:Unlocking driver’s door and fuel filler
flap

Press buttonΠonce.
All turn signal lamps flash once. The
locking knob in the driver’s door moves
up. The anti-theft alarm system is
disarmed.
Global unlocking

Press buttonΠtwice.
All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system is
disarmed.
Global locking

Press button‹.
With the tailgate and all doors closed,
the turn signal lamps flash three times.
The locking knobs in the doors move
down. The anti-theft alarm system is
armed.Restoring to factory setting

Press and hold buttonsŒ and‹
simultaneously for about 5 seconds
until battery check lamp5
(page 108) flashes twice.
!
If you cannot lock or unlock the vehicle with
the SmartKey, the batteries in the SmartKey are
discharged, the SmartKey is malfunctioning, or
the vehicle battery is drained.


Check the batteries in the SmartKey and
replace them if necessary (
page 480).


Use the mechanical key to unlock the
driver’s door (
page 475).


Lock the vehicle as described in the
“Practical hints” section (
page 476).


Have the vehicle battery and the vehicle
battery connections checked (
page 507).
If the SmartKey is malfunctioning, contact
Roadside Assistance or an authorized
Mercedes-Benz Light Truck Center.
ProCarManuals.com

111 Controls in detail
Locking and unlocking
Checking the batteries
Press button‹orŒ.
Battery check lamp5 (
page 108)
comes on briefly to indicate that the
SmartKey batteries are in order.Unlocking and opening the tailgate
(Vehicles with power tailgate*)
You can unlock and open the tailgate sep-
arately.
A minimum height clearance of 7.2 ft
(2.20 m) is required to open the tailgate.

Press and hold buttonŠ on the
SmartKey until the tailgate unlocks and
begins to open.Loss of SmartKey or mechanical key
If you lose a SmartKey or mechanical key,
you should do the following:

Have the SmartKey deactivated by an
authorized Mercedes-Benz Light Truck
Center.

Report the loss of the SmartKey or the
mechanical key immediately to your
car insurance company.

If necessary, have the mechanical lock
replaced.
Your authorized Mercedes-Benz Light
Truck Center will be glad to supply you
with a replacement.
i
If battery check lamp5 does not come on
briefly during check, the SmartKey batteries are
discharged.
Replace the batteries (
page 480).
You can obtain the required batteries at any
authorized Mercedes-Benz Light Truck Center.
i
If the batteries are checked within signal
range of the vehicle, pressing the
button‹orŒ will lock or unlock the
vehicle accordingly.
!
The tailgate swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.
To stop the opening procedure, press
buttonŠ on the SmartKey. The tailgate stops
moving.
i
If the vehicle was previously centrally locked
with the SmartKey, the tailgate will lock automat-
ically when closed. The turn signals will flash
three times to confirm locking.
ProCarManuals.com

116 Controls in detailLocking and unlockingGlobal unlocking
Grasp any outside door handle other
than the driver’s outside door handle.
All turn signal lamps flash once. The
locking knobs in the doors move up.
The anti-theft alarm system is dis-
armed.
Global locking

Press the lock button on an outside
door handle (
page 68).
All turn signal lamps flash three times.
The locking knobs in the doors move
down. The anti-theft alarm system is
armed.Restoring to factory setting

Press and hold buttonsŒ and‹
simultaneously for about 5 seconds
until battery check lamp5
(page 112) flashes twice.Checking the batteries

Press button‹orŒ.
Battery check lamp5 (
page 112)
comes on briefly to indicate that the
SmartKey with KEYLESS-GO batteries
are in order.
!
If you can no longer lock or unlock the
vehicle with the SmartKey with KEYLESS-GO, the
batteries in the SmartKey are discharged, the
SmartKey with KEYLESS-GO is malfunctioning or
the vehicle battery is drained.


Check the batteries in the SmartKey with
KEYLESS-GO (
page 116) and replace
them if necessary (page 480).


Use the mechanical key to unlock the
driver’s door (
page 475).


Lock the vehicle as described in the “Practi-
cal hints” section (
page 476).


Have the vehicle battery and the vehicle
battery connections checked (
page 507).
If the SmartKey with KEYLESS-GO is malfunc-
tioning, contact an authorized Mercedes-Benz
Light Truck Center.
i
If battery check lamp5 (
page 112) does
not come on briefly during check, the SmartKey
with KEYLESS-GO batteries are discharged.
Replace the batteries (
page 480).
You can obtain the required batteries at any
authorized Mercedes-Benz Light Truck Center.
i
If the batteries are checked within signal
range of the vehicle, pressing the
button‹orŒ will lock or unlock the
vehicle accordingly.
ProCarManuals.com

117 Controls in detail
Locking and unlocking
Unlocking and opening the tailgate
(Vehicles with power tailgate*)
You can unlock and open the tailgate sep-
arately.
A minimum height clearance of 7.2 ft
(2.20 m) is required to open the tailgate.
The handle is located above the rear
license plate recess.

Pull on the handle
or

Press and hold buttonŠ on the
SmartKey with KEYLESS-GO until the
tailgate unlocks and opens.Loss of the SmartKey with KEYLESS-GO
If you lose your SmartKey with
KEYLESS-GO or mechanical key, you
should do the following:

Have the SmartKey with KEYLESS-GO
deactivated by an authorized
Mercedes-Benz Light Truck Center.

Report the loss of the SmartKey with
KEYLESS-GO or the mechanical key
immediately to your car insurance
company.

Have the mechanical lock replaced if
necessary.
Your authorized Mercedes-Benz Light
Truck Center will be glad to supply you
with a replacement.
!
The tailgate swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.
To stop the opening procedure, press
buttonŠ on the SmartKey. The tailgate stops
moving.
i
If the vehicle was previously centrally locked
with the SmartKey or SmartKey with
KEYLESS-GO*, the tailgate will lock automatical-
ly when closed (
page 121). The turn signals
will flash three times to confirm locking.
ProCarManuals.com

119 Controls in detail
Locking and unlocking
Opening the tailgate
Opening the tailgate from the outside
A minimum height clearance of 7.0 ft
(2.13 m) is required to open the tailgate.
Vehicles with vehicle level control*:
Depending on the set vehicle level a mini-
mum height clearance of 7.2 ft (2.20 m) is
required to open the tailgate.
The handle is located above the rear
license plate recess.

Pull on the handle.
The tailgate opens slightly.

Pull tailgate upwards to open.
The tailgate can also be opened using the
SmartKey (
page 108).Opening the tailgate from the inside
electrically*
In vehicles with power tailgate* you can
open the tailgate from the inside if the ve-
hicle is stationary.
A minimum height clearance of 7.0 ft
(2.13 m) is required to open the tailgate.
Vehicles with vehicle level control*:
Depending on the set vehicle level a mini-
mum height clearance of 7.2 ft (2.20 m) is
required to open the tailgate.
i
Vehicles without KEYLESS-GO*:
The vehicle must be unlocked (
page 38).
Vehicles with KEYLESS-GO*:
When opening the tailgate, the vehicle is globally
unlocked.
!
The tailgate swings open upwards automat-
ically. Always make sure there is sufficient over-
head clearance.
Vehicles with power tailgate*:
To stop the opening procedure, press
buttonŠ on the SmartKey. The tailgate stops
moving.
i
If the vehicle was previously centrally
locked, the tailgate will lock automatically after
closing it (
page 121). The turn signals will
flash three times to confirm locking.
ProCarManuals.com

128 Controls in detailSeatsFor information on seat adjustment, see
the “Getting started” section (
page 43).
For more information on seats, see “Load-
ing” (
page 281).
Front seat active head restraintsYou cannot remove the active head
restraints on the driver’s and front
passenger’s seat.
For removal of the active head restraints
we recommend that you contact an
authorized Mercedes-Benz Light Truck
Center.
For information on head restraint adjust-
ment, see “Seats” (
page 43).
For information on active head restraints,
see “Active head restraint” (
page 80).
Rear seat head restraints
Warning!
G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is close
to the head as possible and the center of the
head restraint supports the back of the head
at eye level. This will reduce the potential for
injury to the head and neck in the event of
an accident or similar situation.
Warning!
G
Do not drive the vehicle without the seat
head restraints installed when the rear seats
are occupied. Head restraints are intended
to help reduce injuries during an accident.
With a rear seat occupied, make sure to
move the respective head restraint up from
the lowest non-use position and have the oc-
cupant adjust the head restraint properly.
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint in such a way that
it is as close to the head as possible and the
center of the head restraint supports the
back of the head at eye level. This will re-
duce the potential for injury to the head and
neck in the event of an accident or similar
situation.
ProCarManuals.com

136 Controls in detailLightingFor information on how to switch on the
headlamps and use the turn signals, see
“Switching on headlamps” (
page 59)
and “Turn signals” (
page 60).
Exterior lamp switchExterior lamp switchMOff
Daytime running lamp mode
(
page 138)
UAutomatic headlamp mode
Daytime running lamp mode
(page 137)
CParking lamps (also tail lamps,
license plate lamps, side marker
lamps, instrument panel lamps)BLow beam headlamps or high beam
headlamps when the combination
switch is pushed forward. The tail
lamps, license plate lamps, side
marker lamps, parking lamps and
instrument panel lamps also come
on.
ˆStanding lamps, right
(turn left one stop)
‚Standing lamps, left
(turn left two stops)
‡Indicator lamp for front fog lamps
†Indicator lamp for rear fog lamp
i
If you drive in countries where vehicles drive
on the other side of the road than the country in
which the vehicle is registered, you must have
the headlamps modified for symmetrical low
beams. Relevant information can be obtained at
any authorized Mercedes-Benz Light Truck
Center.
i
Vehicles equipped with active Bi-Xenon*
headlamps:
The active Bi-Xenon* headlamps monitor the
vehicles steering angle and vehicle speed, then
automatically shift their beams to either side to
better follow the curvature of the road ahead,
increasing usable illumination over conventional
headlamps.
i
If you hear a warning signal you have
forgotten to switch off the headlamps before
opening the driver’s door.
In addition the message
Switch off lights

appears in the multifunction display.
Switch off the headlamps.
ProCarManuals.com