display MERCEDES-BENZ S-Class 2003 W220 Comand Manual

11 At a glance
Multifunction display

Multifunction display
The starter switch must be in position 1 or
2. Refer to vehicle operating instructions.
You can operate the following systems
with steering wheel buttons 4 and 5:

Radio

CD (CD changer and CD drive)

Auxiliary audio source, e.g. tape recor-
der (
page 200)

Telephone
For more detailed information, refer to
“Multifunction display” in the chapters dis-
cussing the radio, CD, telephone opera-
tion.
Function
1
Multifunction display in speedo-
meterOperating the control system
2
Adjusting the volume
I lowers the volume
J raises the volume
3
Making a call
K Accept incoming call or
starts dialing
L End a call or end Tele Aid
4
Switching between menu sys-
tems
E next system
H previous system
5
Moving within a menu system
F next display
G previous displayFunction

12 At a glanceQuick reference COMAND

Quick reference COMANDThe section “Quick reference COMAND”
summarizes information regarding the
main functions of your COMAND system.
You should read this section with particu-
lar care if you are operating COMAND for
the first time.
For detailed information, please refer to
the pages indicated and the respective
system chapters.Switching on

Press #.
The Mercedes logo and the lettering
Mercedes-Benz will appear. The display
then changes and an alert box will ap-
pear.COMAND switches on the last active
system and displays the corresponding
menu.Switching the COMAND control unit
on and off
P82.85-9534-31US
Mercedes-Benz
P82.85-9535-31US
WARNING
DDo not become distracted from
traffic by use of COMAND.

13 At a glance
Quick reference COMAND
The navigation system was the last sys-
tem used
The menu displayed will vary according to
the last navigation function used.
If route guidance was active:
the symbol display or

the map
If route guidance was active and the
COMAND was switched off for more than
2hours:

an inquiry menu (
page 168)If destination input was active:

the main destination input menuSwitching another system on

Press a system key, e.g. d.
The main CD menu will appear.
Switching off

Press #.
The COMAND control unit will switch
off.
iIf COMAND is switched off for more
than 30 minutes during active route
guidance, all manually entered traffic
jams and detours are deleted. You will
see a corresponding message. Selec-
ting a detour (
page 162).

15 At a glance
Quick reference COMAND
Selecting a station
Automatic seek tuning
Press one of the keys g or h
briefly.
FM- and AM-Bands, Weather Band WB
The radio will tune in to the next recei-
vable station (FM/AM) or channel (WB)
with descending/ascending frequency.
Switching another system on

Press any system key, e.g. d.
COMAND will switch to CD mode.
You will find more information regarding
this topic in section “Radio operation” in
chapter “Audio” (
page 28).Switching on

Press d.
The main CD menu will appear.
Playback will begin in
CD drive with the first track on the
CD

CD changer with the first track on
the first CD detected in the magazi-
ne.Loading a CD into the CD drive and loading
CDs in the CD changer (
page 45).
Track select

Press one of the keys g or h
briefly.
You will hear the previous or next track.
If more than 9 seconds of playing time
has elapsed, the CD changes back to
the start of the current track.
Selecting a CD

Press one of the number keys
Key 0 select the CD drive
Keys 1 - 6 select the corresponding
magazine slot of the
CD changer
The message “Loading CD ...” appears
on the display. Playback then will begin
with track 1.
CD operation
P82.85-9305-31US
CD1CD Select
SettingsSound
CD Naming Scan
Track 1
0:05 min

17 At a glance
Quick reference COMAND
Begin dialing
When the Ä button is highlighted,
press the right-hand rotary/push-
button v to confirm your input.
Dialing will begin. If the phone number
together with a name is stored in the
phone book, the name appears on the
screen.
Conducting a call
When the call is answered, the call time ap-
pears in the screen.
Ending a call

Press the right-hand rotary/push-but-
ton v to confirm the Ö button.
Switching another system on

Press any system key, e.g. b.
COMAND switches to the navigation
system.
You will find more information in chapter
“Telephone” (
page 78).Switching the navigation system on
Main destination input menu

Press b.
If the navigation system has not been
booted up, the message “Navigation
being activated. Please obey all traffic
rules” will appear.
The navigation menu displayed will vary
according to the last navigation func-
tion used (
page 13).
If route guidance was switched off, the
main destination input menu will be
displayed.
Entering a destination and calcula-
ting a route
P82.85-9308-31US
Settings
NAVI Destination Entry
Destn from Memory...
Destination via Map...
Points of Interest...
Last Destinations...Address...

20 At a glanceQuick reference COMAND“Route mode
” selection menu
Select a route and then a traffic route
Turn the right-hand rotary/push-
button v to move the cursor on the
entry you want and press to confirm.
A checkmark appears P.Route types available:

Fast Route

Short Route
Including P/avoiding traffic routes Q

Freeway

Ferry

Toll

Turn the right-hand rotary/push-
button v to highlight “OK” and press
to confirm.
The selected route and the destination
you have entered will appear on the
display.
You will hear the message “The route is
being calculated”.
Symbol displayAfter a few seconds, you will see the sym-
bol display.
CALC. ROUTE Calculation of route
1.0 mi (miles) Distance to destination
(as the crow flies)
P82.85-9314-31US
NAVI Route Mode
Fast Route
Short Route
Freeway
Ferry
Toll
OK
P82.85-9315-31US
DIRECTION TO DESTN.
Map
Stop
Mix
CALC.
ROUTE
1.0 mi

21 At a glance
Quick reference COMAND
The route will be calculated. COMAND
identifies the road you are travelling on.
You will see the arrow indicating the direc-
tion of travel if COMAND recognizes the
road you are travelling on. You will e.g.
hear the message “Please turn right”. Rou-
te guidance will begin.
You will find more information in chapter
“Navigation” (
page 123).Day and night display, switching off
screen

Press Ä repeatedly until the desired
display appears.
The display changes in this order: 
Day display

Night display

Screen off

Day displayYou can switch different beeps on and off.

Acknowledgement beep
Beeps when you accept an entry or en-
ter a destination on the map

Info beep
Beeps when you see the messages an-
nouncing a drop of battery voltage
(page 10)

Alarm beep
Beeps if the device has a serious mal-
function or if you are listening to a di-
saster announcement on the radio. You
can only switch off the beep if you also
switch off COMAND.
You will find more information in chapter
“System settings” (
page 197).
P82.85-9316-31US
Map
Stop
Mix
0.1 miBATTERY PARK/STATE ST
3.4 mi
iIt is also possible to carry out the
change between day and night display
automatically via the light sensor
(page 198).
Selecting beeps

28 AudioRadio operationIn chapter “Audio” you will find detailed in-
formation regarding 
radio operation

CD operation and

sound adjustments
If you have not done so already, please fa-
miliarize yourself with these functions by
reading chapter “At a glance”.
Main radio menu FM1Frequency band (FM, AM, WB) and me-
mory location of station, e.g. “1”
2Station frequency
3Menu fields
Press c to switch to radio operati-
on.
The station last tuned to will begin to
play.Muting

Press o while listening to the radio.
The symbol ß will appear in the top
right corner of the display.

Press o again to resume listening to
the current station.
The symbol ß will have disappeared.

Press any system key, e.g. d.
COMAND will switch to CD mode.
Switching oniYou can operate the telephone and the
navigation system while the radio is on.
P82.85-9317-31US
1
2
3
FM1
FM Presets
Auto Presets Scan
97.1 FM
Sound
WB
iMuting will also be canceled if you
switch to a different audio source, e.g.
CD, or if you alter the volume.Switching another system on

29 Audio
Radio operation
You can select between FM-, AM- and WB-
Band.
AM Band
Press c until “AM” is displayed in
the upper left hand corner of the dis-
play.
The AM station last tuned to will begin
to play. The frequency will appear in
the display.
1 The frequency range is from 530 - 1620 AM in
some countriesWeather Band WB
In the AM or FM main radio menu, turn
the right-hand rotary/push-button v
to highlight WB and press to confirm.
The channel last tuned to will appear in
the display.Switching back to FM band

Press c.
Changing the Radio band
P82.85-9320-31US
AM Presets
Auto Presets Scan
1080 AM
Sound
WB AM1
Frequency band
Frequency range
FM
AM
87.7 - 107.9 FM
530 - 1710 AM
1
P82.85-9321 -31US
WB Presets Scan
Channel 1
Sound WB1
iIf a weather band station cannot be re-
ceived on this channel, an automatic
search run of all 7 channels will take
place. As soon as a weather band stati-
on is received, the search stops and the
channel appears in the display. The au-
tomatic search will perform two cycles
through the 7 channels.
Message “No WB”
A weather band station cannot be recei-
ved on any of the 7 channels.

31 Audio
Radio operation
Seek tuning at the multifunction stee-
ring wheel
If the multifunctional display shows the
station frequency, then:
Press F or G to select a higher/
lower frequency preset.Manual tuning (FM, AM)

Press g or h longer than 2 se-
conds.
The menu fields will appear in dark grey
lettering.FM Band
The frequency displayed will change in in-
crements of 0.2 MHz.
AM Band
Tuning will take place in increments of
10 kHz.
iThe up/down arrows have different
functions depending on which mode the
seek function in the multifunction dis-
play is programmed to.
The two available options are Memory
Scan or Frequency Scan (Station
search). Refer to the vehicle operator’s
manual on how to program this option.
P82.85-9320-31US
AM Presets
Auto Presets Scan
1080 AM
Sound
WB AM1
iActivating the AM Band (
page 29).