remote control MERCEDES-BENZ S CLASS 2007 User Guide

468 Controls in detailUseful features
Remote door unlock
In case you have locked your vehicle unin-
tentionally (e.g. SmartKey inside vehicle),
and the reserve SmartKey is not handy:
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subscriber agreement.
or

Contact the Tele Aid web page via In-
ternet using the ID and password sent
to you shortly after the completion of
your acquaintance call.

Then return to your vehicle and pull the
trunk lid handle for a minimum of
20 seconds until the SOS button be-
gins to flash.
The message: “Call connecting” ap-
pears in the multifunction display and
the SOS button is flashing.
The Response Center will then unlock
your vehicle with the remote door un-
locking feature.
i
The indicator lamp in the respective button
flashes until the call is concluded. Calls can only
be terminated by a Response Center or Custom-
er Assistance Center representative except
Roadside Assistance and Information calls,
which can also be terminated by pressing
buttont on the multifunction steering wheel
or COMAND (
page 115).
!
If the indicator lamp continues to flash or
the system does not terminate the call at all,
contact the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada), or Mercedes-Benz
Customer Assistance at 1-800-FOR-MERCedes
(1-800-367-6372) in the USA or Customer Ser-
vice at 1-800-387-0100 in Canada.
i
When a Tele Aid call has been initiated, the
audio system is muted. The optional mobile
phone (if installed) switches off. If you must use
this phone, the vehicle must be parked. Unplug
the telephone, switch it on and place the call.
The COMAND navigation system (if engaged) will
continue to run. The multifunction display in the
instrument cluster is available for use, but spo-
ken commands are not available.
i
You can exit Roadside Assistance and/ or
the information display during an active connec-
tion and call up the COMAND application last se-
lected. To do so, select “Back”. Meanwhile,
mute remains active (
page 79).
i
The remote door unlock feature is available
if the relevant mobile phone network is available
and data connection is possible.
The SOS button will flash and the message: “Call
connecting” appears in the multifunction display
to indicate receipt of the door unlock command.
Once the vehicle is unlocked, a Response Center
specialist might attempt to establish voice con-
tact with the vehicle occupants.
If the trunk lid handle was pulled for more than
20 seconds before door unlock authorization
was received by the Response Center, you must
wait 15 minutes before pulling the trunk lid han-
dle again.

469 Controls in detail
Useful features
Remote door lock
If you have forgotten to lock your vehicle
and are no longer near it, you can have it
locked remotely through the Response
Center.
The vehicle can be remotely locked within
4 days after the ignition has been switched
off.
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subscriber agreement.
When you are inside your vehicle the next
time and switch on the ignition, the mes-
sage “Tele Aid Doors locked by remote con-
trol” will appear on the multifunction
display.Automatic Maintenance Call
The 2007 S-Class is equipped with a fea-
ture which considerably enhances the care
of your vehicle. Just prior to your vehicle
reaching a maintenance milestone Tele Aid
will initiate a message informing the ser-
vice center, important vehicle mainte-
nance information and the vehicle is due
for a service appointment. The message is
transmitted in the background with no
driver interaction necessary. This feature
allows your preferred Mercedes-Benz Cen-
ter to significantly improve the process of
arranging your service appointment and
ensures that your vehicle receives the best
possible care.Stolen Vehicle Recovery services
In the event your vehicle was stolen:

Report the incident to the police.
The police will issue a numbered
incident report.

Pass this number on to the
Mercedes-Benz Response Center along
with your password issued to you when
you subscribed to the service.
The Response Center will then attempt
to covertly contact the vehicle’s
Tele Aid system. Once the vehicle is
located, the Response Center will
contact the local law enforcement and
you. The vehicle’s location will only be
provided to law enforcement.
i
The remote door lock feature is available if
the relevant mobile phone network is available
and data connection is possible.
i
The Automatic Maintenance Call feature is
available if the relevant mobile phone network is
available and data connection is possible.
i
When the anti-theft alarm or the tow-away
alarm stays on for more than 30 seconds, a call
is initiated automatically to the Response Cen-
ter. See anti-theft alarm system (
page 75) and
tow-away alarm (
page 76).

470 Controls in detailUseful featuresGarage door opener
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated re-
mote control1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control but-
ton
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park the vehicle outside the garage.

471 Controls in detail
Useful features
Programming integrated remote con-
trol
Step 1:
Switch on the ignition (
page 315).
Step 2:

If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and be-
gin directly with step 3.
Step 3:

Hold the end of the hand-held remote
control5 of the device you wish to
train approximately 2 to 5 in
(5 to12 cm) away from the signal trans-
mitter button (2, 3 or4) to be pro-
grammed, while keeping the indicator
lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held remote control
button6 and the desired signal trans-
mitter button (2, 3 or4). Do not
release the buttons until step 5 is com-
pleted.The indicator lamp1 will flash, first
slowly and then rapidly.
Step 5:

After the indicator lamp1 changes
from a slow to a rapidly flashing light,
release the hand-held remote control
button and the signal transmitter but-
ton.
Step 6:

Press and hold the just-trained signal
transmitter button (2, 3 or4) and
observe the indicator lamp1.
If the indicator lamp1 stays on
constantly, programming is complete
and your device should activate when
the respective signal transmitter
button (2, 3 or4) is pressed and re-
leased.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and possible death.
i
The indicator lamp1 flashes immediately
the first time the signal transmitter button is pro-
grammed. If this button has already been pro-
grammed, the indicator lamp will only start
flashing after 20 seconds.

473 Controls in detail
Useful features
If you live in Canada or if you are having
difficulties programming a gate operator
(regardless of where you live) by using the
programming procedures, replace step 4
with the following:
Step 4:
Press and hold the signal transmitter
button (2, 3 or4). Do not release
this button until it has been successful-
ly trained.

While still holding down the signal
transmitter button (2, 3 or4),
“cycle” your hand-held remote control
button6 as follows: Press and hold
button6 for 2 seconds, then release
it for 2 seconds, and again press and
hold it for 2 seconds. Repeat this se-
quence on the hand-held remote con-
trol until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.Reprogramming a single signal trans-
mitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Switch on the ignition (
page 315).

Press and hold the desired signal
transmitter button (2, 3 or4).
Do not release the button.

The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the signal transmitter button, pro-
ceed with programming starting with
step 3.Operation of integrated remote control

Switch on the ignition (
page 315).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing integrated remote control
memory

Switch on the ignition (
page 315).

Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.
i
Upon completion of programming the inte-
grated remote control, make sure you retain the
hand-held remote control that came with the ga-
rage door opener, gate operator or other device.
You may need it for use in other vehicles, for fu-
ture programming of an integrated remote con-
trol, or simply for continued use as a hand-held
remote control to operate the respective device
in other situations.

474 Controls in detailUseful featuresProgramming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:

Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.


Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.


While performing step 3, hold the
hand-held remote control5 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.


If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.


Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
i
If you sell your vehicle, erase the codes of all
three channels.
i
Certain types of garage door openers are in-
compatible with the integrated remote control. If
you should experience further difficulties with
programming the integrated remote control,
contact an authorized Mercedes-Benz Center, or
call Mercedes-Benz Customer Assistance Cen-
ter (in the USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.
i
USA only:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interfer-
ence, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.
i
Canada only:
This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference re-
ceived, including interference that may
cause undesired operation of the device.
Any unauthorized modification to this device
could void the user’s authority to operate the
equipment.

685 Index
Dynamic Rear View Monitor* 413
Parallel parking 417
Reverse parking (back-in
parking) 415
Switching on 415
View through the camera 413
E
Easy-entry/exit feature 328
COMAND menu 224
EBP 71
ELCODE 672
Electric parking brake 364
Electrical fuses see Fuses
Electrical outlet see Power outlet
Electrical system, Technical Data 659
Electronic Brake Proportioning see EBP
Electronic Stability Program see ESP
®
Emergency call system 462
Emergency calls, Tele Aid 463
Emergency engine shut-down 648
Emergency operation (Limp-Home
Mode) 377
Emergency operations
Locking the vehicle 614
mechanically releasing the parking
brake 616Releasing from inside 440
Remote door lock 469
Remote door unlock 468
Tilt/sliding sunroof or tilt/sliding
panel* 617
Unlocking the trunk 615
Unlocking the vehicle 614
Emergency tensioning device see ETD
Emergency, In case of
Battery, Jump starting 639
First aid kit 611
Flat tire 629
Fuses 645
Instrument cluster, Indicator
lamps 544
Roadside Assistance 16
Roadside Assistance (Tele Aid) 465
Towing the vehicle 642
Emission control 488
Emission control information label 652
Emission control system warranties 14
Engine
Belt layout 653
Cleaning 536
Compartment 492
Coolant 497, 662, 665Malfunction indicator lamp 547
Number 652, 672
Oil 496, 661, 663
Oils 494
Residual heat and ventilation 433
Starting 359
Technical data 654
Turning off 365
Engine coolant see Coolant
Engine oil 494
Adding 496
Additives 663
Checking level 494
Checking level (Dipstick) 495
Checking level (Instrument cluster con-
trol system) 494
Consumption 494
Dipstick 495
Filler neck 496, 497
Messages in display 495, 602
Recommended engine oils and oil
filters 661
Viscosity 672
ESP
®
72
Messages in display 572, 582
Warning lamp 549

688 IndexInfant and child restraint systems see Chil-
dren in the vehicle
Inflation pressure see Tires
Infrared reflecting windshield 475
Inside door handle 312
Instrument cluster 28, 378, 674
Cleaning 541
Coolant temperature gauge 378
Illumination 81, 378
Lamps 544
Multifunction display 241
Outside temperature indicator 379
Selecting the language
(COMAND) 216
Interior lighting 348
Activating automatic control 349
Ambient lighting (COMAND) 225
Deactivating automatic control 349
Delayed switch-off (COMAND) 226
In the rear 350
Reading lamps in the front 349
Reading lamps in the rear 350
Interior rear view mirror
Adjusting 332
Auto-dimming 334Interior storage spaces see Storage com-
partments
J
Jack 612, 630
Jacking up the vehicle 630
Jump starting 639
K
Key, Mechanical 614
Loss of 311
Key, SmartKey 304
Battery check lamp 304, 305
Factory setting 305
Global locking and unlocking 305
Lock button 304
Locking and unlocking 304
Loss of 311
Messages in display 593
Opening button for trunk 304
Panic button 68
Remote control 304
Restoring to factory setting 306
Selective setting 305
Starting the engine 359
Switching on ignition with 315Turning off engine 366
Unlock button 304
Key, SmartKey with KEYLESS-GO* 306
Battery check lamp 306, 310
Closing, Trunk 440
Factory setting 309
Global locking and unlocking 309
Important notes on using
KEYLESS-GO* 308
Lock button 306
Locking and unlocking 306
Locking using the lock button on door
or on trunk lid 310
Loss of 311
Messages in display 592
Opening button for trunk 306
Panic button 68
Remote control 306
Restoring to factory setting 310
Selective setting 310
Starting the engine 360
Switching on ignition with 317
Turning off engine 366
Unlock button 306
Kickdown 373, 674
Kilopascal 527

694 IndexRecovery services, Stolen vehicle (Tele
Aid) 469
Refrigerant, Air conditioning 662, 663
Refueling 489
Regular checks 490
Remote
Control, SmartKey 304
Control, SmartKey with
KEYLESS-GO* 306
Door lock with Tele Aid 469
Door unlock with Tele Aid 468
Trunk opening switch 436
Trunk opening/closing* switch 437,
438
Replacing
Bulbs 621
Front lamp bulbs 623
Rear lamp bulbs 622
Reporting safety defects 21
Research Octane Number see RON
Reset (COMAND) 219
Residual engine heat and ventilation 433
Residual heat utilization 677
REST 676REST (Residual engine heat
utilization) 677
REST see Residual engine heat and ventila-
tion
Rest tool
Depository 618
Restraint systems
Messages in display 605
See Children in the vehicle
See SRS
Reverse gear position, Automatic
transmission 367, 370
Rims 527
And Tires 655
Tires and wheels 500
Roadside Assistance 16
Tele Aid 465
RON 490, 662, 677
Roof rack* 447
Route guidance (COMAND) 185
Route guidance (Instrument cluster control
system) 246
Rubber and plastic parts, Cleaning 541
Run Flat Indicator (Canada only) 515S
Safety
Driving safety systems 69
Occupant 44
Reporting defects 21
Safety belts see Seat belts
Satellite radio*
Calling Sirius Service Center
(COMAND) 103
Channel update (COMAND) 103
Operation (COMAND) 98
Selecting channel (Instrument cluster
control system) 248
Selecting program category
(COMAND) 100
Showing program info
(COMAND) 103
Submenu overview (COMAND) 98
Tuning in channels (COMAND) 100,
102
Voice Control* 283

697 Index
Symbols used in this operator’s
manual 18
System settings (COMAND)
Bluetooth settings 217
Display 213
Favorite button 216
Menu overview 213
Reset 219
Setting the system language 216
Time settings 213
Voice Control* settings
(COMAND) 215
T
Tachometer 379
Overspeed range 379
Tail lamps
Cleaning lenses 537
Messages in display 600
Tar stains 535
Tele Aid 462, 677
Automatic Maintenance Call 469
Call priority 467
Emergency calls 463
Hands-free microphone 37
Information 466Information button 465
Initiating an emergency call
manually 464
Messages in display 607
Remote door lock 469
Remote door unlock 468
Roadside Assistance 465
Roadside Assistance button 465
SOS button 464
Stolen Vehicle Recovery
services 469
System self-check 462
Telematics 677
Telephone cradle
Changing 461
Telephone* 459
“911” emergency call
(COMAND) 117
Accepting/ending a call
(COMAND) 124
Answering/ending a call (Instrument
cluster control system) 252
Call lists (COMAND) 122
Changing mobile phone cradle 461
Dialing (Instrument cluster control
system) 250Entering the telephone number
(COMAND) 125
Hands-free microphone 37
Inserting in cradle 460
Installing a different mobile phone
cradle 461
Operation 249
Operation (COMAND) 115
Phone book (COMAND) 129
Phone book (Instrument cluster control
system) 250
PIN (COMAND) 119
PIN2 (COMAND) 119
PUK / PUK2 (COMAND) 119
Redialing (COMAND) 125
Redialing (Instrument cluster control
system) 251
Removing from cradle 461
Single call connection
(COMAND) 127
Speed dialing (COMAND) 126
Submenu overview (COMAND) 120
Switching on/off (COMAND) 116
Transferring a call (COMAND) 128
Unlock code (COMAND) 119
Voice Control* 262