MERCEDES-BENZ S550 4MATIC 2008 W221 Owner's Manual

270 Control systems
Instrument cluster control system
Route guidance active
The image on the multifunction display de-
pends on whether you are being notified of
a driving maneuver.
No notification of driving maneuver
Example illustration
1Distance to destination
2Symbol for “follow the course of the
road”
3Distance to next driving maneuver
4Street you are currently driving onNotification of driving maneuver with-
out lane recommendation
Example illustration
1Street into which the driving maneuver
leads
2Symbol for “driving maneuver”
3Distance to driving maneuver and visu-
al distance display
When you are being notified of a driving
maneuver, you will see a visual distance
display 3 next to the driving maneuver
symbol. The visual distance display is re-
duced from bottom to top the closer you
come to the announced driving maneuver.Navigation status displays in the instru-
ment cluster
While route guidance is active, the follow-
ing messages may be shown on the multi-
function display:

<
You have reached your destination.

“Area of dest. reached”
You have arrived in the area of your
destination. The message appears, for
example, for relatively large POIs.

“New Route…”
COMAND calculates a new route, e.g.
because you have deviated from the
calculated route or due to a detour re-
port. Afterward, COMAND continues
route guidance.

271 Control systems
Instrument cluster control system

“Calculating Route”
COMAND is calculating a route. After-
ward, COMAND starts route guidance.

“Off Map”
The vehicle’s location is outside of the
digital map’s range. The vehicle is in an
off-map position (
page 212).

“Off Road”
The vehicle is either on a road that has
not been digitized (
page 212) or on
the side of a road, e.g. in a parking
space.

“No Route”
COMAND cannot calculate a route to
the selected destination.

“Direction of Dest.”
The vehicle has gone off the map dur-
ing route guidance (
page 212).
Audio menu
The functions in the “Audio” menu operate
the audio equipment which you currently
have turned on.
If no audio equipment is currently turned
on, the message: “Audio off” is shown in
the multifunction display.
Selecting radio station
Turn on COMAND and select “Radio”
(
page 100).
Press ( or & to select the “Au-
dio” menu.
Press % or $ to select a station.1Station frequency
2Waveband
Press æ or ç to adjust the vol-
ume.
Selecting satellite radio* channel
(USA only)
The satellite radio is treated as a radio ap-
plication.
Turn on COMAND and select “Sat Ra-
dio” (
page 105).
iThe menu overview can be found on
(
page 266).
iYou can only change the frequency band
and save new stations using COMAND
(
page 100).


272 Control systems
Instrument cluster control system
Press ( or & to select the “Au-
dio” menu.
Press % or $ to select a station.
1Channel number and/or name
2SAT mode
Press æ or ç to adjust the vol-
ume.Operating DVD changer/audio CD/
audio DVD/MP3
Turn on COMAND and select “CD”,
“DVD-Audio” or “MP3” (
page 112).
Press ( or & to select the “Au-
dio” menu.
Press % or $ to select a track.
Example: audio CD
1Current track
Press æ or ç to adjust the vol-
ume.Operating video DVD (USA only)
Turn on COMAND and select “Video”

“Video”
“Video DVD”
(
page 126).
Press ( or & to select the “Au-
dio” menu.
1Current scene
2Disc number
Press % or $ to select a scene.i A subscription to SIRIUS satellite radio ser-
vice provider is required for the satellite radio op-
eration. Contact an authorized Mercedes-Benz
Center for details and availability for your
vehicle.
For more information on satellite radio
(
page 105).iWhen you play a CD or DVD with text, the
multifunction display shows the name and num-
ber of the track. For MP3s, only the track is
shown.


273 Control systems
Instrument cluster control system
AMG menu
The main screen of the AMG menu shows
you

the gear currently engaged

the engine oil temperature

the vehicle supply voltage
Press ( or & to select the
“AMG” menu.
1Gear indicator
2Upshift indicator
3Engine oil temperature
4Vehicle supply voltageIf the engine reaches the overspeed range
in the manual shift program, you will see
“up” 2 next to gear indicator 1 as a re-
minder to upshift.
Use buttons % or $ to select the fol-
lowing functions in the AMG menu:RACETIMER
The RACETIMER allows you to time and
save driving stretches in hours, minutes
and seconds.
Press ( or & to select the
“AMG” menu.
Press % to select the RACETIMER.
iThis function is only available in S 63 AMG
and S 65 AMG.
iThe engine oil temperature symbol will be
shown in blue if the engine oil temperature has
not yet reached 176°F (80°C). During this time,
avoid driving at full engine speed.
FunctionPage
RACETIMER273
Overall analysis275
Lap analysis275
Warning!G
The RACETIMER feature is for use only on
roads and in conditions where high speed
driving is permitted. Racing on public roads
is prohibited under all circumstances and
the driver is and must always remain re-
sponsible for following posted speed limits.


274 Control systems
Instrument cluster control system
1Gear indicator
2RACETIMER
3Seconds display
4Lap
Starting RACETIMER: Press æ.
Displaying intermediate time:
Pressç.
The intermediate time is shown for
5 seconds.
Stopping RACETIMER: Press æ.
To select a different display, press
$, ( or &.Saving lap time and starting a new lap
Press buttonç while the timer is
running.
The intermediate time will be shown for
5 seconds.
Press buttonç within 5 seconds.
The intermediate time shown will be
saved as a lap time.
The RACETIMER begins timing the new
lap. The new lap begins to be timed as
soon as the intermediate time is called
up.
1Gear indicator
2RACETIMER
3Best lap time
iYou can start the RACETIMER when the en-
gine is running or the starter switch is in
position2 (
page 344).
iWhile the RACETIMER is being displayed,
you cannot adjust the audio volume using but-
tons æ or ç.
iWhen you stop the vehicle and turn the
Smartkey to position 1 (
page 344) or, in vehi-
cles with KEYLESS-GO*, turn off the engine and
do not open the driver’s door, the RACETIMER
stops timing. Timing is resumed when you switch
the ignition back on or restart the engine and
then press æ button.
iWhen you switch on the Night View Assist*
(
page 461) while the RACETIMER is operating,
the RACETIMER will continue to run in the back-
ground but cannot be operated with the multi-
function steering wheel buttons.
To stop the RACETIMER, switch off the Night
View Assist* first.
iYou can save up to 16 laps.


275 Control systems
Instrument cluster control system
Resetting current lap
Press buttonæ while the timer is
running.
The timer stops.
Press buttonç.
The lap time is reset to “0”.
Deleting all laps
Press buttonæ while the timer is
running.
The timer stops.
Pressç for at least 3 seconds.
Press buttonæ.
The timer starts. The saved laps are de-
leted.Overall analysis
Press ( or & to select the
“AMG” menu.
Press $ repeatedly until the overall
analysis appears in the multifunction
display.
1Overall analysis of RACETIMER
2Overall driving time
3Maximum speed
4Overall distance driven
5Average speed
To select a different display, press
$, ( or &.Lap analysis
Press ( or & to select the
“AMG” menu.
Press $ repeatedly until the lap
analysis appears in the multifunction
display.
1Lap number
2Lap time
3Maximum speed
4Lap length
5Average speed during lap
Press $ or % to see other lap
analyses.
iIt is not possible to delete a single saved lap.
iThese functions are only available if you
have saved at least one lap and have stopped the
RACETIMER.iThese functions are only available if you
have saved at least two laps and have stopped
RACETIMER.


276 Control systems
Instrument cluster control system
To select a different display, press
( or &.Telephone* menu
You can use the functions in the “Tele-
phone” menu to operate your telephone,
provided it is inserted in the cradle and
switched on.
iEach lap is shown in its own submenu. The
fastest lap is indicated by flashing symbol 1.iThe menu overview can be found on
(
page 266).
Warning!G
Some jurisdictions prohibit the driver from
using a cellular telephone while driving.
Whether or not prohibited by law, for safety
reasons, the driver should not use the cellu-
lar telephone while the vehicle is in motion.
Stop the vehicle in a safe location before
placing or answering a call.
If you nonetheless choose to use the mobile
phone while driving, please use the hands-
free feature and be sure to pay attention to
the traffic situation at all times. Use the mo-
bile phone only when road, weather and traf-
fic conditions permit.
Otherwise, you may not be able to observe
traffic conditions and could endanger your-
self and others.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approxima-
tely 14 m) every second.
Warning!G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or
personal injury.


277 Control systems
Instrument cluster control system
Logging-on to a network
Switch on the telephone and COMAND
(
page 85).
Press ( or & to select the “Tele-
phone” menu.
Which messages appear in the multifunc-
tion display depends on whether your tele-
phone is switched on or off.

If the telephone is off, the message in
the multifunction display is: “Telephone
OFF”.

If the telephone is not inserted in the
cradle, the message in the multifunc-
tion display is: “No telephone inserted”.

If the PIN or unlock code is not yet en-
tered, the message in the multifunction
display is “Please enter PIN” or “Enter
unlock code”.

If the telephone is switched on, the
telephone will then search for a net-
work. During this time, the multifunc-
tion display is blank. If no network
available, the multifunction display
reads “No Service”.

If the telephone is on, as soon as the
telephone has found a network,
“Ready” or “Ready (Roaming)” appears
in the multifunction display.Entering the PIN or unlock code
Enter the PIN or unlock code using the
telephone keypad*, Voice Control* or
telephone*.
The telephone will then search for a
network.
You may carry out the following functions:
Dialing a number from the mobile
phone book
If your telephone is ready to receive calls,
you may select and dial a number from the
phone book at any time.
Log on to the network (page 277).
iVarious mobile phone cradles can be in-
stalled in the front center armrest, see separate
installation instructions for the mobile phone
cradle. These mobile phone cradles can be ob-
tained from an authorized Mercedes-Benz Cen-
ter. For more information about telephone
(
page 507).
iThe roof cargo container* may impair mo-
bile phone reception. In an emergency, remove
the mobile phone from the mobile phone cradle
(
page 507) to make a call.FunctionPage
Dialing a number from the phone
book277
Redialing278
Answering a call279
Ending a call or rejecting an in-
coming call279


278 Control systems
Instrument cluster control system
Press % or $ or # to switch
to the phone book.
Press % or $ to select the de-
sired name.
The stored names are displayed in as-
cending alphabetical order.
Press s or # to start dialing.
If several entries are present for the
same name, they are all shown.
Select the desired entry.
Press s or # to start dialing.
The message “Connecting call…” ap-
pears on the multifunction display, as
well as the dialed telephone number or
name as long as it is stored in the
phone book.
The dialed number is saved in the “Di-
aled numbers” list.
Once a connection has been estab-
lished, the name appears on the multi-
function display, provided that it has been stored in the phone book, other-
wise the dialed telephone number ap-
pears.
Redialing
The control system stores the most recent-
ly dialed phone numbers. This eliminates
the need to search through your entire
phone book.
Log on to the network (page 277).
Press s to switch to the number
and/or name last dialed in the redial
memory.
Press % or $ to select the de-
sired number and/or name.
Press s or # to start dialing.
Once a connection has been estab-
lished, the name appears in the multi-
function display, provided that it has
been stored in the phone book, other-
wise the dialed telephone number ap-
pears.
iWhen you insert a Mercedes-Benz approved
mobile phone into the cradle*, the control sys-
tem reads in the phone book that is saved on the
SIM card or in the phone book of the mobile
phone. This can take several minutes, depending
on how many entries each phone book contains.
When you press %, $, (, & or
# during the download of the phone book the
message “Reading telephone data, please
wait...” appears in the multifunction display.
When the message: “Reading telephone data,
please wait...” disappears, the phone book has
been loaded.
iIf you do not want to dial from the phone
book, press t or L. In the multifunction
display appears again “Ready” or “Ready (Roam-
ing)”.
iIf you press and hold % or $ for
more than 1 second, the system scrolls
rapidly through the list of names.
If you press and hold % or $ for more than
4 seconds, the control system shows the first
four entries of the letter next used. Release the
button to stop the quick search. The search
stops automatically at the end of the list.

279 Control systems
Instrument cluster control system
Answering a call
When your telephone is ready to receive
calls, you can answer a call at any time
with the ignition on. When you are in the
“Telephone” menu, you will see the follow-
ing message on the multifunction display:
Press s.
Ending a call or rejecting an incoming
call
Press t.
Assistance* menu
In the “Assistance” menu, you can change
the settings of your driving systems.
Displaying distance graphic*,
DISTRONIC Plus* (USA only)
For information about displaying distance
graphic (
page 428).
Activating/deactivating PRE-SAFE
®
Brake* (USA only)
Press ( or & to select the
“Assistance” menu.
Press % or $ to select the
“PRE-SAFE Brake” function.
Press #.1PRE-SAFE
® Brake* indicator:
Press # again if you would like to
change the current status.
After the function has been activated,
indicator: appears on the
left-hand side of the multifunction dis-
play.
For more information (
page 76).
Switching on the Dynamic Rear View
Monitor* automatically
Press ( or & to select the
“Assistance” menu.
iThe caller’s number appears only if it is
transmitted.
The caller’s name appears only if the number and
the name are stored in the phone book.
iThe menu overview can be found on
(
page 266).
iThe image from the Dynamic Rear View
Monitor is shown on the COMAND display.