key MERCEDES-BENZ SL55AMG 2004 R230 Repair Manual
Page 145 of 434
144 Controls in detailControl systemTo select delayed switch-off period:
Move the selection marker with button
æ or ç to the
Lighting
sub-
menu.
Press button j or k repeatedly
until you see this message in the left
display:
Headlamps delayed
switch-off
.
The selection marker is on the current
setting.
Press æ or ç to select the de-
sired lamp-on period.
You can select:
0 s
, the delayed switch-off feature
is deactivated
15 s
, 30 s
, 45 s
or
60 s
, the delayed
switch-off feature is activatedYou can temporarily deactivate the de-
layed switch-off feature:
Before leaving the vehicle turn the
SmartKey in the starter switch to
position0.
Then turn it to position2 and back
to0.
The delayed switch-off feature is deac-
tivated. It will reactivate as soon as you
reinsert the SmartKey in the starter
switch.
For vehicles with KEYLESS-GO*:
Press the KEYLESS-GO start/stop but-
ton on the gear selector (
page 33).
iYou can reactivate this function within
ten minutes by opening a door.
If you do not open a door after remov-
ing the SmartKey from the starter
switch, the lamps will automatically
switch off after 60 seconds.
Page 146 of 434
145 Controls in detail
Control system
Interior lighting delayed switch-off
Use this function to set whether and for
how long you would like the interior light-
ing to remain lit during darkness after the
SmartKey is removed from the starter
switch.
Move the selection marker with button
æ or ç to the
Lighting
sub-
menu.
Press button j or k repeatedly
until you see this message in the left
display:
Int. lighting delayed
switch-off
.
The selection marker is on the current
setting.
Press æ or ç to select the de-
sired lamp-on time period. You can se-
lect:
0 s
, the delayed switch-off feature
is deactivated
5 s
, 10 s
, 15 s
or
20 s
, the delayed
switch-off feature is activatedVehicle submenu
Access the
Vehicle
submenu via the
Set-
tings
menu. Use the
Vehicle
submenu to
make general vehicle settings. The follow-
ing functions are available:
Function
Page
Set station selection mode
(radio)
146
Set automatic locking
146
Tire pressure display*
147
Page 149 of 434
148 Controls in detailControl systemConvenience submenu
Access the
Convenience
submenu via the
Settings
menu. Use the
Convenience
sub-
menu to change the settings for a number
of convenience features. The following
functions are available:
Activating easy-entry/exit feature
Use this function to activate and deacti-
vate the easy-entry/exit feature. When the
feature is activated, the steering wheel and
driver’s seat will move back to facilitate ex-
iting the vehicle when you
remove the SmartKey from the starter
switch
open the driver’s doorAfter entering the vehicle, the steering
wheel and seat will move into the position
stored in memory when
the driver’s door is closed
you insert the SmartKey in the starter
switch or press the KEYLESS-GO*
start/stop button and
press and hold the appropriate stored
position button on the memory switch
(page 114)
Move the selection marker with button
æ or ç to the
Convenience
sub-
menu.
Press button j or k repeatedly
until you see this message in the left
display:
Easy-entry feature Acti-
vate
.
The selection marker is on the current
setting.
Function
Page
Activate easy-entry/exit fea-
ture
148
Set key-dependency
149
Set parking position for exterior
rear view mirror
149
Warning!
G
You must make sure that no one can be-
come trapped or injured by the moving
steering wheel and the driver’s seat when
the easy-entry / exit feature is in operation
and the driver’s door is being opened or the
SmartKey is removed from the starter
switch.
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
iTo cancel seat/steering wheel move-
ment, press one of the following:
the seat adjustment switch
(page 34)
the steering column switch
(page 37)
the memory switch (
page 114)
Page 150 of 434
149 Controls in detail
Control system
Press æ or ç to change the
easy-entry/exit setting.
The following settings are available for the
easy-entry/exit feature:Setting key-dependency
Use this function to set whether the mem-
ory settings for the seats, the steering
wheel and the exterior rear view mirrors
mirrors should be stored separately for
each SmartKey (
page 114).
Move the selection marker with button
æ or ç to the
Convenience
sub-
menu.
Press button j or k repeatedly
until you see this message in the left
display:
Key-dependent
.
The selection marker is on the current
setting.
Press æ or ç to set key-depen-
dency to
On or
Off
. Setting parking position for exterior rear
view mirror
Use the
Mirror setting when parking
function to select whether the passen-
ger-side exterior rear view mirror should be
turned downward during parking maneu-
vers when reverse gear R is engaged. For
additional information, see “Activating ex-
terior rear view mirror parking position”
(
page 167).
Move the selection marker with button
æ or ç to the
Convenience
sub-
menu.
Press button j or k repeatedly
until you see this message in the left
display:
Mirror setting when park-
ing
.
Off
The easy-entry/ex-
it feature is deacti-
vated
Steer. column
Only the steering
column is moved
Steer.col. +seat
Both, the steering
column and the
seat are moved
Page 152 of 434
151 Controls in detail
Control system
Fuel consumption since last reset
Press button ÿ or è repeatedly
until you see the first function of the
Trip computer menu.
Press button j or k repeatedly
until you see this message in the left
display:
From reset.
1Distance driven since last reset
2Average speed since last reset
3Time elapsed since last reset
4Average fuel consumption since last re-
setResetting fuel consumption statistics
Press button ÿ or è repeatedly
until you see the first function of the
Trip computer menu.
Press button j or k repeatedly
until you see the reading that you want
to reset in the left display.
Press and hold the reset button in the
instrument cluster (
page 23) until
the value is reset to 0.
iAll statistics stored since the last en-
gine start will be reset approximately
four hours after the SmartKey in the
starter switch is turned to position0 or
removed from the starter switch.
Resetting will not occur if you turn the
SmartKey back to position1 or2 with-
in this time period.
Page 159 of 434
158 Controls in detailAutomatic transmissionGear selector lever position
Effect
ì
Park position
Gear selector lever position
when the vehicle is parked. Place
gear selector lever in positionP
only when vehicle is stopped.
The park position is not intended
to serve as a brake when the
vehicle is parked. Rather, the
driver should always set the
parking brake in addition to
placing the gear selector lever in
positionP to secure the vehicle.
EffectThe SmartKey can only be
removed from the starter switch
with the gear selector lever in
positionP. With the SmartKey
removed, the gear selector lever
is locked in positionP.
í
Reverse gear
Place gear selector lever in
positionR only when vehicle is
stopped.
Effect
ë
Neutral
No power is transmitted from the
engine to the drive axle. When
the brakes are released, the
vehicle can be moved freely
(pushed or towed).
To avoid damage to the trans-
mission, never engageN while
driving.
If the ESP is deactivated or
malfunctioning:
Move gear selector lever toN
only if the vehicle is in danger of
skidding, e.g. on icy roads.
ê
Drive
The transmission shifts
automatically. All forward gears
are available.
Page 160 of 434
159 Controls in detail
Automatic transmission
!
Coasting the vehicle, or driving for any
other reason with gear selector lever
inN can result in transmission damage
that is not covered by the
Mercedes-Benz Limited Warranty.
Warning!
G
Getting out of your vehicle with the gear
selector lever not fully engaged in positionP
is dangerous. Also, positionP alone is not
intended to or capable of preventing your
vehicle from moving, possibly hitting people
or objects.
Always set the parking brake in addition to
shifting to positionP (
page 45).
When parked on an incline, turn the front
wheels towards the road curb.
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take the
SmartKey with KEYLESS-GO* with you and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Children could move the
gear selector lever from positionP, which
could result in an accident and/or serious
personal injury.
Page 179 of 434
178 Controls in detailAutomatic climate controlResidual heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.Activating
Turn the SmartKey in the starter switch
to position1 or0 or remove it from the
starter switch.
Press button T (
page 171).
The indicator lamp on button T
comes on.Deactivating
Press button T (
page 171).
The indicator lamp on button T
goes out.
The residual heat is automatically turned
off:
when the ignition is switched on
after about 30 minutes
if the battery voltage drops
iHow long the system will provide heat-
ing depends on the coolant tempera-
ture and the temperature set by the
operator. The blower will run at speed
setting1 regardless of the air distribu-
tion control setting.
Page 182 of 434
181 Controls in detail
Power windows
Power windows
Opening and closing the windows
The side windows can be opened and
closed electrically. The switches for all the
side windows are on the driver’s door. The
switch for the passenger side is on the pas-
senger door.
1Left front and rear windows
2Right front and rear windows
Switch on ignition.
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being injured
by the closing procedure.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if the switch was pulled past the resistance
point and released, by either pressing or
pulling the respective switch.
If the window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the window,
the automatic reversal function will stop the
window and open it slightly.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pulling and
holding the switch, by pressing and holding
button
‹
on the SmartKey,
or by pressing and holding the lock button
(vehicles with KEYLESS-GO*) on the door
handle, the automatic reversal function will
not operate.
When leaving the vehicle, always remove the
SmartKey from the starter switch, take the
SmartKey with KEYLESS-GO* with you, and
lock your vehicle. Do not leave children un-
attended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment can cause an accident
and/or serious personal injury.iYou can also open or close the win-
dows using the , button on the
control panel of the automatic climate
control (
page 175).
Page 184 of 434
183 Controls in detail
Power windows
Stopping windows
Press or pull the respective switch
again.
Closing the windows with the
SmartKey with KEYLESS-GO*
Press and hold lock button at door
(page 55) until the side windows are
closed.
Synchronizing power windows
The power window must be resynchro-
nized each time
after the battery has been disconnect-
ed
if the power windows cannot be fully
opened (Express-open) or closed
(Express-close)
Synchronizing the power windows
Switch on ignition.
Pull the power window switches until
the side windows are closed.
Hold the switches for approximately
one second.
The power windows are synchronized.
Warning!
G
When closing the windows make sure that
there is no danger of anyone being harmed
by the closing procedure.
The windows will not automatically re-open
if blocked during convenience closing.
If potential danger exists, proceed as fol-
lows:
Release the lock button.
Pull on the door handle and hold firmly.
The side windows open for as long as
the door handle is held but the door not
opened.