MERCEDES-BENZ SL600 2007 R230 Owner's Manual
Page 161 of 473
160 Controls in detailControl systemSetting locator lighting
With the locator lighting feature activated
and the exterior lamp switch in position
U, the following lamps will switch on
during darkness when the vehicle is un-
locked with the SmartKey:
Parking lamps
Tail lamps
License plate lamps
Front fog lamps
Side marker lamps
The locator lighting switches off when the
driver’s door is opened.
If you do not open a door after unlocking
the vehicle with the SmartKey, the lamps
will switch off automatically after approxi-
mately 40 seconds.
Move the selection marker with button
æ or ç to the
Lighting
sub-
menu.
Press button j or k repeatedly
until the message
Locator lighting
appears in the multifunction display.
The selection marker is on the current
setting.
Press button æ or ç to switch
the locator lighting feature to
On.
Turn the exterior lamp switch to posi-
tion U when exiting the vehicle.
The locator lighting feature is
activated.Setting night security illumination
(Exterior lamps delayed switch-off fea-
ture)
Use this function to set whether you would
like the exterior lamps to remain on for 15
seconds during darkness after exiting the
vehicle and closing the doors.
With the delayed switch-off feature activat-
ed and the exterior lamp switch in position
U before the engine is turned off, the
following lamps will switch on when the en-
gine is turned off:
Parking lamps
Tail lamps
License plate lamps
Side marker lamps
Front fog lamps
Page 162 of 473
161 Controls in detail
Control system
If after turning off the engine you do not
open a door or do not close an opened
door, the lamps will switch off automatical-
ly after 60 seconds.
Move the selection marker with button
æ or ç to the
Lighting
sub-
menu.
Press button j or k repeatedly
until the message
Headlamps delayed
switch-off
appears in the multifunc-
tion display.
The selection marker is on the current
setting.
Press button æ or ç to switch
the delayed switch-off feature
On or
Off
.
Turn the exterior lamp switch to posi-
tion U before turning off the engine.
The delayed switch-off feature is acti-
vated.
You can temporarily deactivate the de-
layed switch-off feature:
Before exiting the vehicle turn the
SmartKey in the starter switch to
position0.
Then turn it to position2 and back
to0.
The delayed switch-off feature is deac-
tivated. It will reactivate as soon as you
reinsert the SmartKey in the starter
switch.Setting interior lighting delayed
switch-off
Use this function to set whether you would
like the interior lighting to remain on for
10 seconds during darkness after you have
removed the SmartKey from the starter
switch.
Move the selection marker with button
æ or ç to the
Lighting
sub-
menu.
Press button j or k repeatedly
until the message
Int. lighting
delayed switch-off appears in the
multifunction display.
The selection marker is on the current
setting.
Page 163 of 473
162 Controls in detailControl system
Press æ or ç to switch the inte-
rior lighting delayed switch-off feature On or
Off
.
Vehicle submenu
Access the Vehicle
submenu via the
Set-
tings
menu. Use the
Vehicle
submenu to
make general vehicle settings. The follow-
ing functions are available:
Setting automatic locking
Use this function to activate or deactivate
the automatic central locking. With the
automatic central locking system
activated, the vehicle is centrally locked at
a vehicle speed of approximately
9mph(15km/h).
Move the selection marker with the
æ or ç button to the
Vehicle
submenu.
Press button j or k repeatedly
until you see this message in the left
multifunction display: Automatic door lock
.
The selection marker is on the current
setting.
Press æ or ç to switch Automatic door lock
On or
Off
.Convenience submenu
Access the
Convenience
submenu via the
Settings
menu. Use the
Convenience
sub-
menu to change the settings for a number
of convenience features. The following
functions are available:
Activating easy-entry/exit feature
Use this function to activate and deacti-
vate the easy-entry/exit feature
(
page 46).
Function
Page
Setting automatic locking
162
Function
Page
Activating easy-entry/exit
feature
162
Page 164 of 473
163 Controls in detail
Control system
Move the selection marker with the
æ orç button to the
Conve-
nience
submenu.
Press button j or k repeatedly
until you see
Activate Easy-entry
feature
in the multifunction display.
The selection marker is on the current
setting.
Press æ or ç to switch the
easy-entry/exit feature
On or
Off
.
Trip computer menu
Use the trip computer menu to call up sta-
tistical data on your vehicle. The following
information is available:
Warning!
G
You must make sure no one can become
trapped or injured by the moving steering
wheel when the easy-entry/exit feature is
activated.
To stop steering wheel adjustment, do one
of the following:
Move steering column stalk
(page 45).
Press the memory button (
page 126).
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
Function
Page
Fuel consumption statistics after
start
164
Fuel consumption statistics
since last reset
164
Distance to empty
165
i
The last function called up will reappear the
next time you enter the trip computer menu.
Page 165 of 473
164 Controls in detailControl systemFuel consumption statistics after start
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see this message in the left
multifunction display:
From start.
1Distance driven since start
2Average speed since start
3Time elapsed since start
4Average fuel consumption since startFuel consumption since last reset
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see this message in the left
multifunction display:
From reset.
1Distance driven since last reset
2Average speed since last reset
3Time elapsed since last reset
4Average fuel consumption since last re-
setResetting fuel consumption statistics
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see the reading that you want
to reset in the left multifunction dis-
play.
Press and hold the reset button in the
instrument cluster (
page 27) until
the value is reset to 0.
i
All statistics stored since the last engine
start will be reset approximately 4 hours after
the SmartKey in the starter switch is turned to
position0 or removed from the starter switch.
Resetting will not occur if you turn the SmartKey
back to position1 or2 within this time period.
i
The fuel consumption statistics reset auto-
matically to
0 when either of the following values
is exceeded:
distance covered:100 000 miles
time elapsed: 10 000 hours
Page 166 of 473
165 Controls in detail
Control system
Distance to empty
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see this message in the left
multifunction display:
Range
.
In the right multifunction display you
will see the calculated range based on
the current fuel tank level.
TEL menu*
You can use the functions in the
TEL
menu
to operate your telephone, provided it is
connected to a hands-free system and
switched on.
Switch on the telephone and COMAND.
Press button ÿ or è on the
steering wheel repeatedly until you see
the
TEL
menu in the left multifunction
display.
i
If only very little fuel is left in the tank, a ve-
hicle at the fuel pump is shown instead of the
range.
Warning!
G
A driver’s attention to the road must always
be his/her primary focus when driving. For
your safety and the safety of others, we rec-
ommend that you pull over to a safe location
and stop before placing or taking a tele-
phone call. If you choose to use the tele-
phone while driving, please use the
hands-free device and only use the tele-
phone when weather, road, and traffic con-
ditions permit.
Some jurisdictions prohibit the driver from
using a cellular telephone while driving a ve-
hicle.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or
personal injury.
Page 167 of 473
166 Controls in detailControl systemWhich messages will appear in the right
multifunction display depends on whether
your telephone is switched on or off:
If the telephone is off, the message in
the multifunction display is:
TEL off
.
If the telephone is on:
The telephone will then search for a
network. During this time the right mul-
tifunction display is empty.
As soon as the telephone has found a
network,
READY
is indicated in the right
multifunction display.
This standby message indicates that
your telephone is ready for use and you
can operate it using the control sys-
tem.Answering a call
When your telephone is ready to receive
calls, you can answer a call at any time. In
the right multifunction display you will then
see the message:
Press button s.
You have answered the call. In the right
multifunction display you see the dura-
tion of the call.Ending a call
Press button t.
You have ended the call. In the right
multifunction display you will again see
the standby message.
Dialing a number from the phone book
If your telephone is ready to receive calls,
you may select and dial a number from the
phone book at any time.
Press button ÿ or è repeatedly
until you see the
TEL
menu in the left
multifunction display.
In the right multifunction display you
will see the standby message.
i
If you do not wish to accept a call, press
button t.
Page 168 of 473
167 Controls in detail
Control system
Press button j or k.
The control system reads the phone
book which is stored in the telephone.
This may take several minutes. In the
right multifunction display you will see
the message
Please wait!
.
When the message
Please wait!
dis-
appears, the phone book has been
loaded.
Press button j or k repeatedly
until the desired name appears in the
right multifunction display.
The stored names are displayed in
ascending or descending alphabetical
order.
Press button s.
The system dials the selected phone
number.
If the connection is successful and this
feature is supported by your network
provider, the name of the party you are
calling (if stored in your phone book)
and the duration of the call will appear
in the display.
If no connection is made, the control
system stores the dialed number in the
redial memory. Redialing
The control system stores the most recent-
ly dialed phone numbers. This eliminates
the need to search through your entire
phone book.
Press button ÿ or è repeatedly
until you see the
TEL
menu in the left
multifunction display.
In the right multifunction display you
will see the standby message.
Press button s.
In the right multifunction display you
see the first number in the redial mem-
ory.
Press button j or k repeatedly
until the desired name appears in the
right multifunction display.
Press button s.
The control system dials the selected
phone number.
i
If you press and hold j or k for long-
er than one second, the system scrolls rapidly
through the list of names until you release the
button again.
Cancel the quick search mode by pressing t.
Page 169 of 473
168 Controls in detailAutomatic transmissionFor more information on driving with an
automatic transmission, see “Automatic
transmission” (
page 52).
Your vehicle’s transmission adapts its gear
shifting process to your individual driving
style by continually adjusting the shift
points up or down. These shift point adjust-
ments are performed based on current
operating and driving conditions.
If the operating conditions change, the
automatic transmission reacts by
adjusting its shift program.
Gearshift pattern for automatic
transmission
The automatic transmission selects indi-
vidual gears automatically, depending on:
the gear selector lever
positionD(
page 170) with
gear ranges (page 172)
the selected program mode:
(C/S) (
page 173)
or
(MANUAL/C/S) (SL 55 AMG and
SL 65 AMG only) (
page 177)
the position of the accelerator pedal
(page 171)
the vehicle speed
i
During the brief warm-up, transmission up-
shifting is delayed. This allows the catalytic con-
verter to heat up more quickly to operating
temperature.
Page 170 of 473
169 Controls in detail
Automatic transmission
1Current gear range/gear selector lever
position
2Current program mode
The current gear range/gear selector lever
position and program mode (
C/S) or
(
M/C/S) appear in the right multifunction
display.When the gear selector lever is in
positionD, you can influence transmission
shifting by:
limiting the gear range
changing gears manually
Warning!
G
It is dangerous to shift the gear selector
lever out ofP orN if the engine speed is
higher than idle speed. If your foot is not
firmly on the brake pedal, the vehicle could
accelerate quickly forward or reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.
!
Allow engine to warm up under low load use.
Do not place full load on the engine until the op-
erating temperature has been reached.
Shift into reverse gearR or parking positionP
only when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road surfac-
es. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.