steering wheel MERCEDES-BENZ SL600 2008 R230 Owner's Guide

130 Controls in detail
Memory function
Storing positions into memory
Adjust the seats, steering wheel and
exterior rear view mirrors to the
desired position (
page 43).
Press memory buttonM.
Release memory button and press a
stored position button1, 2, or3 within
3 seconds.
All the settings are stored at the
selected position.
Recalling positions from memory
On memory switch, press and hold
stored position button1, 2 or3 until
the seat, steering wheel and exterior
rear view mirrors have fully moved to
the stored positions.
iReleasing the button immediately stops
movement to the stored positions.

136 Controls in detail
Lighting
High beam
Canada only: Turn the exterior lamp
switch to position B (
page 131).
or
USA only: Turn the exterior lamp switch
to positionB or U (
page 131).
Push the combination switch in
direction of arrow1 to switch on the
high beam.
The high beam headlamp indicator
lamp A in the instrument cluster
comes on.
Pull the combination switch in direction
of arrow 2 to its original position to
switch off the high beam.
The high beam headlamp indicator
lamp A in the instrument cluster
goes out.
High beam flasher
Pull the combination switch briefly in
direction of arrow2.
Corner-illuminating front fog lamps*
The corner-illuminating front fog lamps
improve illumination of the area in the
direction into which you are turning.
The corner-illuminating front fog lamps will
operate with the engine running and with

the exterior lamp switch in
positionB (
page 131)
or

the exterior lamp switch in
positionU (
page 131)
or

the daytime running lamp mode
activated (
page 133)Driving forward
Switching on corner-illuminating front
fog lamps
Switch on the left or right turn signal
(
page 57), depending on whether
you are turning left or right.
The respective front fog lamp comes
on and illuminates the area in the
direction into which into which you
are turning.
or
Turn the steering wheel in the desired
direction.
The front fog lamp on the side of your
steering direction comes on.
iThe corner-illuminating front fog lamps will
only come on in low ambient lighting conditions.
iIf you are driving faster than
25 mph (40 km/h) or have the front fog lamps
switched on, the corner-illuminating function is
not available.
iIf you have switched on the turn signal for
one side but turn the steering wheel in the
opposite direction, the corner-illuminating lamp
comes on for the side indicated by the turn
signal.
The corner-illuminating front fog lamp remains lit
for a maximum of 3 minutes. Afterwards, it goes
out even if the turn signal is still switched on.

137 Controls in detail
Lighting
Switching off corner-illuminating front
fog lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating front fog lamps if they
were activated by switching on the left or
right turn signal.If the turn signal should stay on after
making the turn, the turn signal and
corner-illuminating front fog lamp can be
switched off by returning the combination
switch to its original position.
Driving in reverse
Switching on corner-illuminating front
fog lampsPlace the gear selector lever in
positionR.
The front fog lamp opposite to your
steering direction comes on.
Switching off corner-illuminating front
fog lamps
Place the gear selector lever out of
positionR.
The respective front fog lamp goes out.
Hazard warning flasher
The hazard warning flasher can be
switched on at all times, even with the
SmartKey removed from the starter switch
or with the SmartKey with KEYLESS-GO*
removed from the vehicle.
The hazard warning flasher switches on
automatically when an air bag deploys.
The hazard warning flasher switch is
located on the upper part of the
center console.
1Hazard warning flasher switchiThe corner-illuminating front fog lamps
temporarily come on both sides of the vehicle
if you turn the steering wheel in one direction
and then again in the other direction shortly
thereafter.
iThe corner-illuminating front fog lamps
will come on automatically depending on the
steering angle, even if you did not switch on
either turn signal.
If the corner-illuminating front fog lamps came
on automatically, they will also go out automati-
cally depending on the steering angle.iThere may be a brief delay before the
corner-illuminating front fog lamps switch off.

141 Controls in detail
Instrument cluster
Coolant temperature gaugeResetting trip odometer
Make sure you are viewing the trip
odometer display (
page 143).
If it is not displayed, press the
jork button on the multi-
function steering wheel repeatedly
until the trip odometer appears.
Press and hold reset button1
(
page 140) until the trip odometer is
reset.
Warning!G

Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.

Steam from an overheated engine can
cause serious burns which can occur
just by opening the hood. Stay away
from the engine if you see or hear steam
coming from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
!Excessive coolant temperature triggers the
coolant temperature warning lamp (
page 348)
and a warning in the multifunction display
(
page 383).
The engine should not be operated with the cool-
ant temperature above 248°F (120°C). Doing so
may cause serious engine damage which is not
covered by the Mercedes-Benz Limited
Warranty.
iDuring severe operating conditions, e.g.
stop-and-go traffic, the coolant temperature may
rise close to 248°F (120°C).

143 Controls in detail
Control system
Control system
The control system is activated as soon
as the SmartKey in the starter switch is
turned to position1 or as soon as the
KEYLESS-GO start/stop button is in
position 1. The control system enables
you to

call up information about your vehicle

change vehicle settings
For example, you can use the control
system to find out when your vehicle is
next due for service, to set the language
for messages in the instrument cluster
display, and much more.
The control system relays information to
the multifunction display.
Multifunction display
The multifunction display consists of the
display fields in the speedometer and the
tachometer. In its default state, the left
multifunction display shows the main
odometer and the outside temperature,
while the trip odometer appears in the
right multifunction display. This default
setting is referred to as the standard
display.
1Main odometer
2Outside temperature
3Current gear selector lever position
4Trip odometer
5Automatic transmission program mode
Warning!G
A driver’s attention to the road and traffic
conditions must always be his/her primary
focus when driving.
For your safety and the safety of others,
selecting features through the multifunction
steering wheel should only be done by the
driver when traffic and road conditions
permit it to be done safely.
Bear in mind that at a speed of just
30 mph (approximately 50 km/h), your
vehicle is covering a distance of 44 feet
(approximately 14 m) every second.

144 Controls in detail
Control system
Multifunction steering wheel
The displays in the multifunction display
and the settings in the control system are
controlled by the buttons on the multifunc-
tion steering wheel.1Left multifunction display in the
speedometer
2Right multifunction display in the
tachometer
Operating the control system
3Selecting the submenu or setting the
volume:
Press button
æup / to increase
çdown / to decrease
4Telephone*:
Press button
sto take a call
to dial
to redial
tto end a call
to reject an incoming call
5Menu systems:
Press button
èfor next menu
ÿfor previous menu
6Moving within a menu:
Press button
jfor next display
kfor previous display

145 Controls in detail
Control system
Depending on the selected menu, pressing
the buttons on the multifunction steering
wheel will alter what appears in the multi-
function display.
The information available in the multifunc-
tion display are arranged in menus and
accompanying functions or submenus.
The individual functions are then found
within the relevant menu (radio or CD op-
erations under
AUDIO, for example). These
functions serve to call up relevant informa-
tion or to customize the settings for your
vehicle.It is helpful to think of the menus, and the
functions within each menu, as being ar-
ranged in a circular pattern.

If you press button è or ÿ re-
peatedly, you will pass through each
menu one after the other.

If you press button k or j re-
peatedly, you will pass through each
function display, one after the other, in
the current menu. In the
Settings menu, instead of functions
you will find a number of submenus for
calling up and changing settings. For in-
structions on using these submenus, see
“Settings menu” (
page 157).
The number of menus available in the sys-
tem depends on which optional equipment
is installed in your vehicle.
The menus are described on the following
pages.

167 Controls in detail
Control system
Move the selection marker with
theæ orç button to the

Convenience
submenu.
Press button j or k repeatedly
until the message
Easy-entry
Function
appears in the multifunction
display.
The selection marker is on the current
setting.
Press button æ or ç to switch
the easy-entry/exit feature
On or Off.
Trip computer menu
Use the trip computer menu to call up
statistical data on your vehicle.
The following information is available:
Warning!G
You must make sure no one can become
trapped or injured by the moving steering
wheel when the easy-entry/exit feature is
activated.
To stop steering wheel movement, do one of
the following:

Move steering wheel adjustment stalk
(
page 47).

Press one of the memory position
buttons* or the memory button M*
(
page 129).
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
FunctionPage
Fuel consumption statistics
since start168
Fuel consumption statistics
since last reset168
Resetting fuel consumption
statistics168
Distance to empty169
iThe last function called up will reappear the
next time you enter the trip computer menu.

169 Controls in detail
Control system
Distance to empty
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see this message in the left
multifunction display:
Range.
In the right multifunction display you
will see the calculated range based on
the current fuel tank level.
TEL* menu
You can use the functions in the
TEL menu
to operate your telephone, provided it is
connected to a hands-free system and
switched on.
Switch on the telephone and COMAND.
Press button ÿ or è on the
steering wheel repeatedly until the
TELmenu appears in the left multi-
function display.iIf only very little fuel is left in the tank, a
vehicle at the fuel pump is shown instead of the
range.
Warning!G
A driver’s attention to the road must always
be his/her primary focus when driving. For
your safety and the safety of others, we rec-
ommend that you pull over to a safe location
and stop before placing or taking a tele-
phone call. If you choose to use the tele-
phone while driving, please use the
hands-free device and only use the tele-
phone when weather, road, and traffic con-
ditions permit.
Some jurisdictions prohibit the driver from
using a cellular telephone while driving a
vehicle.
Bear in mind that at a speed of just
30 mph (approximately 50 km/h), your
vehicle is covering a distance of
44 feet (approximately 14 m) every second.
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system,
possibly resulting in an accident and/or
personal injury.

176 Controls in detail
Automatic transmission
Stopping
When you stop briefly, e.g. at traffic lights:
Leave the transmission in gear.
Hold the vehicle with the brake.
When you stop for a longer period of time
with the engine idling and/or on a hill:
Set the parking brake.
Move the gear selector lever to park
positionP.Maneuvering
When you maneuver in tight areas,
e.g. when pulling into a parking space:
Control the vehicle speed by gradually
releasing the brakes.
Accelerate gently.
Never abruptly step on the accelerator.
Working on the vehicle
Gear ranges
With the gear selector lever in drive
positionD and driving in program modeC
orS, you can select a gear range for the
automatic transmission to operate within.
Gear selector lever (
page 179):
You can limit the gear range by pressing
the gear selector lever to the left (D-), and
reverse the gear range limit by pressing
the gear selector lever to the right (D+).
Steering wheel gearshift control*
(
page 180):
You can limit the gear range by pulling the
left gearshift paddle on the steering wheel
gearshift control, and reverse the gear
range limit by pulling the right gearshift
paddle on the steering wheel gearshift
control.Warning!G
When working on the vehicle, set the
parking brake and move gear selector lever
to park positionP. Otherwise the vehicle
could roll away.