MERCEDES-BENZ SL65AMG 2008 R230 Owner's Manual

430 Practical hints
Batteries
Open the hood (page 282).
Use the 10 mm open-end wrench from
the vehicle tool kit to disconnect the
negative lead from negative
terminal2 of the starter battery
(
page 427).
Remove the covers from the positive
terminals 1 and 4 (
page 427).
Disconnect the positive lead from pos-
itive terminal 4 of the consumer bat-
tery (
page 427).
Disconnect the positive lead from pos-
itive terminal 1 of the starter battery
(
page 427).
Removing the batteries
Removing the consumer battery
Remove the screws securing the bat-
tery in the trunk.
Remove the battery support and
bracket.
Pull out the battery ventilation hose
from the battery.
Depending on battery arrangement in
your vehicle model, the ventilation tube
is located either on the left or right side
of the battery.
Take out the battery.
Removing the starter battery
Remove the screws securing the start-
er battery in the engine compartment.
Pull battery ventilation 3
(
page 427) out of the battery.
Lift the retaining bracket.
Remove the battery.
Charging and reinstalling batteries
Warning!G
Never charge a battery while still installed in
the vehicle unless the accessory battery
charge unit approved by Mercedes-Benz is
being used. Gases may escape during charg-
ing and cause explosions that may result in
paint damage, corrosion or personal injury.
An accessory battery charge unit specially
adapted for Mercedes-Benz vehicles and
tested and approved by Mercedes-Benz is
available, permitting the charging of the
battery in its installed position. Contact an
authorized Mercedes-Benz Center for infor-
mation and availability. Charge battery in
accordance with the separate instructions
for the accessory battery charger.


431 Practical hints
Batteries
Charge batteries in accordance with
the instructions of the battery charger
manufacturer.
Reinstall the charged batteries. Follow
the previously described steps in re-
verse order.
Reconnecting the batteries
Turn off all electrical consumers.
Install starter battery in the designated
location in the engine compartment.
Install consumer battery in the desig-
nated location in the trunk.
Attach supports and brackets.
Tighten support and bracket screws.
Connect positive lead 4 (page 427)
of the consumer battery and positive
lead 1 (
page 427) of the starter bat-
tery and fasten covers.
Connect negative lead 2
(
page 427) of the starter battery.
Connect negative lead 5
(
page 427) of the consumer battery.
Reinstall the trunk floor.
Close trunk luggage cover
(
page 211).
!Always connect the batteries in the order
described below. Otherwise the vehicle’s elec-
tronics can be damaged.
!Never invert the terminal connections!
iThe following procedures must be carried
out following any interruption of battery power
(e.g. due to reconnection):

Synchronize the ESP® (page 367).

Synchronize side windows (page 203).

432 Practical hints
Jump starting
If the starter battery is discharged, the en-
gine can be started with jumper cables and
the battery of another vehicle. Observe the
following:

Jump starting should only be performed
when the engine and catalytic
converter are cold.

Do not start the engine if the battery is
frozen. Let the battery thaw out first.

Only jump start from batteries with the
same voltage rating (12 V). Jump start-
ing with a higher voltage battery could
damage the vehicle’s electrical system,
which will not be covered by the
Mercedes-Benz Limited Warranty.

Only use jumper cables with sufficient
cross section and insulated terminal
clamps.

Always make sure the jumper cables
are not on or near pulleys, fans, or
other parts that move when an engine
is started or running.
Warning!G
Failure to follow these directions will cause
damage to the electronic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it exploding, causing personal
injury.
Read all instructions before proceeding.
!Do not tow-start the vehicle.
!Jump starting may only be performed on the
battery installed in the engine compartment.
Avoid repeated and lengthy starting attempts.
Do not attempt to start the engine using a bat-
tery quick charge unit.
If the engine does not run after several unsuc-
cessful starting attempts, have it checked at the
nearest authorized Mercedes-Benz Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the
catalytic converter and may present a fire risk.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still
attached to a battery.

433 Practical hints
Jump starting
The starter battery is located on the right
side of the engine compartment.
Make sure the two vehicles do not
touch.
Turn off all electrical consumers.
Apply the parking brake (page 63).
Make sure the gear selector lever is set
to position P (
page 172).
Open the hood (page 282).
Remove the red cover from positive ter-
minal on both vehicles (
page 427).1Positive terminal of charged battery
2Positive terminal of discharged battery
3Negative terminal of discharged
battery
4Negative terminal of charged battery
Connect positive terminals 1 and 2
of the batteries with the red jumper
cable. Clamp cable to charged battery
first.
Start the engine of the vehicle with the
charged battery and run at idle speed.
Connect negative terminals 3 and 4
of the batteries with the black jumper
cable. Clamp cable to charged battery
first.
Start the engine of the disabled vehi-
cle.
You can now turn on the electrical con-
sumers. Do not switch on the headlamps
under any circumstances.
Remove the jumper cables first from
negative terminals 4 and 3 and then
from positive terminals 2 and 1.
You can now switch on the headlamps.
Have the battery checked at the near-
est authorized Mercedes-Benz Center.
Warning!G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(
page 290).
!Never invert the terminal connections.

434 Practical hints
Towing the vehicle
Mercedes-Benz recommends that the vehi-
cle be transported with all wheels off the
ground using flatbed or appropriate wheel
lift/dolly equipment.
When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground or front wheels raised only so
far as necessary to have the vehicle moved
to a safe location where the recommended
towing methods can be employed.
!Do not tow-start the vehicle.
!Use flatbed or wheel lift/dolly equipment
with SmartKey in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Switch off the tow-away alarm (
page 100) and
the automatic central locking (
page 166).
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the
electro-hydraulic brake system

there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the SmartKey
is in starter switch position2.
Warning!G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is
increased! Adapt your driving style
accordingly. For more information, see
“Electro-hydraulic brake system”
(
page 94).
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.

435 Practical hints
Towing the vehicle
!If the vehicle is towed with the front axle
raised, the gear selector lever must be in
positionN and the engine must be shut off
(SmartKey in starter switch position0 or1).
Active braking action through the ESP
® may
otherwise seriously damage the brake system.
When towing the vehicle with all wheels on the
ground, the gear selector lever must be in
positionN and the SmartKey must be in starter
switch position2.
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle
may be towed only for distances up to
30 miles (50 km) and at a speed not to exceed
30 mph (50 km/h).
!Towing of the vehicle should only be done
using the properly installed towing eye bolt.
Never attach a tow cable, tow rope or tow rod to
the vehicle chassis, frame or suspension parts.
iWhen towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position2, or
KEYLESS-GO* start/stop button in position2,
the vehicle doors lock if the left front wheel as
well as the right rear wheel are turning at vehicle
speeds of approximately 9 mph (15 km/h) or
more.
To prevent the vehicle door locks from locking,
deactivate the automatic central locking
(
page 122).
iTo signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position2 and activate the
combination switch for the left or right turn
signal in the usual manner – only the selected
turn signal will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
iIf the battery is disconnected or discharged

the SmartKey will not turn in the starter
switch

the gear selector lever will remain locked in
positionP.
For more information, see “Batteries”
(
page 427) and “Jump starting” (page 432).

436 Practical hints
Towing the vehicle
Installing towing eye bolt
Front
Example illustration (SL 550 and SL 600
without Sport Package)
1Cover on passenger side of front
bumper
To remove cover:
Press mark on cover 1 in direction of
arrow.
Lift cover1off to reveal the threaded
hole for towing eye bolt.To reinstall cover:
Fit locking tabs of cover under the
lower edge of the opening in the
bumper.
Apply even pressure on the upper part
of the cover until it snaps into place.
Rear
1Cover on passenger side of rear
bumper
To remove cover:
Insert flat, blunt object as a lever into
upper left or right recess of cover 1.
Loosen cover 1 using the lever.
Fold cover 1 down in direction of
arrow to reveal the threaded hole for
the towing eye bolt.
To reinstall cover:
Fit cover 1 and snap into place.
Installing towing eye bolt
Take the towing eye bolt and the wheel
wrench from the vehicle tool kit
(
page 400).
Screw towing eye bolt into threaded
hole to its stop.
Insert wheel wrench into towing eye
and tighten towing eye bolt by turning
it clockwise.
Removing towing eye bolt
Take the wheel wrench from the
vehicle tool kit (
page 400).
Insert wheel wrench into towing eye
and loosen towing eye bolt by turning it
counterclockwise.
Remove towing eye bolt.

437 Practical hints
Fuses
Fuses
The electrical fuses in your vehicle serve to
switch off malfunctioning power circuits.
If a fuse is blown, the components and sys-
tems secured by that fuse will stop operat-
ing.If a newly inserted fuse blows again, have
the cause determined and rectified by an
authorized Mercedes-Benz Center.
A fuse chart explains the fuse allocation
and fuse amperages. It is located in the
trunk with the vehicle tool kit
(
page 400).
The electrical fuses are located in different
fuse boxes:

on the driver’s side of the engine com-
partment (
page 438)

on the passenger side of the engine
compartment (
page 438)

under passenger-side rear storage
compartment (
page 439)

in the trunk (page 439)Before replacing fuses:
Apply the parking brake (page 63).
Make sure the gear selector lever is set
to position P (
page 172).
Turn off all electrical consumers.
Turn off the engine (page 64).
Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*: Open
the driver’s door.
Warning!G
Only use fuses approved by Mercedes-Benz
with the specified amperage for the system
in question and do not attempt to repair or
bridge a blown fuse. Using other than
approved fuses or using repaired or bridged
fuses may cause an overload leading to a
fire, and/or cause damage to electrical
components and/or systems. Have the
cause determined and remedied by an
authorized Mercedes-Benz Center
iA blown fuse must be replaced by an appro-
priate spare fuse (recognizable by its color or the
fuse rating given on the fuse) of the amperage
recommended in the fuse chart.
Any Mercedes-Benz Center will be glad to advise
you on this subject.
iIn case of a blown fuse contact Roadside
Assistance or an authorized Mercedes-Benz
Center.

438 Practical hints
Fuses
Fuse boxes in engine compartment
Open the hood (page 282).
The fuse boxes are located on the driver’s
and passenger side in front of the bulk-
head (wall separating the engine and
passenger compartment).
Fuse box on driver’s side
1Fuse box cover
2Locking
3Unlocking
Fuse box on passenger side
1Fuse box cover
2Locking
3UnlockingOpening
Move slide to position 3 and lift
cover1.
Closing
Hook cover 1 onto tabs and close it.
Move slide to position 2.
Close the hood after checking or
replacing fuses (
page 283).
!The fuse box cover must be properly
positioned with the slide at the ‹symbol to
prevent moisture or dirt from entering the fuse
box and possibly impairing fuse operation.

439 Practical hints
Fuses
Fuse box in passenger compartment
The fuse box is located under the rear
passenger-side storage compartment.
1Clips
2Storage compartment floor
Open the rear passenger-side storage
compartment (
page 240).
Lift both clips 1.
Remove storage compartment floor 2
in direction of arrow.
You can now access the fuses.
To reinstall storage compartment
floor2 after checking or replacing
fuses, follow the procedure in reverse
order.
Fuse in trunk
The fuse in the trunk is located on the
right-hand side of the trunk.
Lift up the trunk floor cover.
Emergency engine shut-down
If the engine cannot be turned off as
described, you may use the following
emergency procedure.
Take the fuse chart from the vehicle
tool kit (
page 400).
Find row “Engine emergency stop” in
the fuse chart table to identify the
fuses that have to removed as well as
their locations.
Remove the respective fuses.