check engine MERCEDES-BENZ SLC 2017 User Guide

Problems with the windshield wipers Problem
Possible causes/consequences and P Solutions
The windshield wipers
are jammed. Leaves or snow, for example, may be obstructing the windshield wiper
movement .T he wiper motor has been deactivated. X
For safety reasons, you should remove the SmartKey from the igni-
tion lock.
or X
Switch off the engine using the Start/Stop button and open the
driver's door. X
Remove the cause of the obstruction. X
Switch the windshield wipers back on.
The windshield wipers
fail completely. The windshield wiper drive is malfunctioning. X
Select another wiper speed on the combination switch. X
Have the windshield wipers checked at aq ualified specialist work-
shop.
The windshield washer
fluid from the spray noz-
zles no longer hits the
center of the windshield. The spray nozzles are misaligned. X
Have the spray nozzles adjusted at aq ualified specialist workshop.Windshield wipers 101
Lights and windshiel dw ipers Z

As soo na st he ignition is switched on, al lt he
indicator lamps in the instrument cluster light
up .F urther informatio nons it uations where an
indicator lamp either fails to go ou ta fte rs tarting
the engine or lights up whil ed riving
( Y
page 204).
If Start/Stop button C ha sn ot ye tb ee n
pressed, thi sc orrespond stot he key being
remove df rom the ignition.X
To switc hont he power supply: press
Start/Stop button C once.
The powe rs uppl yiss wi tched on. Yo uc an now
activate the windshield wipers, for example.
The powe rs uppl yiss wi tched off agai ni f:R
the driver's door is opene da ndR
yo up ress Start/Stop button C twice when
in thi sp ositionX
To switc hont he ignition: press Start/Stop
button C twice.
The ignition is switched on.
If yo up ress Start/Stop button C once when
in thi sp osit ion, the ignition is switched off
again.
Removing the Start/Sto pb uttonYo uc an remove the Start/Stop button from the
ignition lock and start the vehicl easn ormal
using the SmartKey. X
Remove Start/Stop button C from ignition
lock D .
Yo udon ot have to remove the Start/Stop but-
ton from the ignition lock when yo ul eave the
vehicle. Yo us hould, however, always take the
SmartKe yw it hy ou when leaving the vehicle. As
long as the Sma rtKe y isint h
e vehicle:R
the vehicl ec an be started using the Start/
Stop button R
the electrically powered equipment can be
operated Starting the engine
Important safety notes
G WARNING
If children ar el ef tu nsupervised in the vehicle,
they could: R
open the doors ,t hu se ndangering other
people or roa du se rs.R
ge to ut and disrupt traffic. R
operate the vehicle's equipment.
Additionally, children could set the vehicl ei n
motion if, for example, they: R
release the parking brake. R
shifting the automatic transmission ou to f
park position P R
Star tt he engine.
There is ar is kofana ccident and injury.
Whe nl eavi ng the vehicle, always take the
SmartKe yw it hy ou and lock the vehicle. Never
leav ec hildren or animals unattended in the
vehicle. Alway sk ee pt he SmartKe yo ut of
reach of children.
G WARNING
Combustion engine se mi tp oiso nou se xhaust
gases such as carbo nm onoxide. Inhaling
thes ee xhaus tg as es lead stop oiso ning. There
is ar is koff ata li njury .T herefore neve rl eave
the engine running in enclose ds paces with-
ou ts uf ficient ventilation.
G WARNING
Flammabl em at erial si ntroduced through
environmenta li nfluence or by animals can
ignite if in contact with the exhaus ts ys tem or
parts of the engine tha th ea tu p. There is ar isk
of fire.
Carry ou tr egular checks to make sure that
ther ea re no flammabl ef oreig nm at erial si n
the engine compartment or in the exhaust
system.
During ac ol ds tart, the engine runs at higher
speed stoe nabl et he catalytic converter to116
Driving
Driving an dp arking

Problem
Possible causes/consequences and P Solutions
The coolant temperature
gauge shows av alue
above 248 ‡( 120 †).
The coolant warning
lamp may also be on and
aw arning tone may
sound. The coolant level is too low. The coolant is too hot and the engine is no
longer being cooled sufficiently. X
Stop as soon as possible and allow the engine and the coolant to
cool down. X
Check the coolant level ( Y
page 233). Observe the warning notes
as you do so and add coolant if necessary.
If the coolant level is correct ,t he engine radiator fan may be faulty. The
coolant is too hot and the engine is no longer being cooled sufficiently. X
At coolant temperatures below 248 ‡( 120 †), drive to the nearest
qualified specialist workshop. X
Avoid heavy loads on the engine as you do so, e.g. driving in moun-
tainou st errai na nd stop-and-go traffic.
DYNAMIC SELEC Tb uttonUse the DYNAMIC SELECT button to change the
drive program. Depending on the drive program
selected the following vehicle characteristics
wil lc hange: R
the drive (engine and transmission manage-
ment) R
the suspensio n( vehicles with adaptive
adjustabl ed amping or AMG sports suspen-
sion) R
the steering R
the availability of the ECO start/stop function
Each time you start the engine with the Smart-
Key or the Start/Stop button, drive program C is
activated. For further information about starting
the engine, see ( Y
pag e1 16).
X
Press DYNAMIC SELECT button C as many
times as necessary until the desired drive
progra miss elected.
The selected drive progra ma ppears in the
multifunction display. After as hort time the displa yg oes out and the status icon of the
selected drive progra ma ppears.
In addition, the current drive progra ms ettings
are displayed briefly in the multimedi as ystem
display.
i In af ew countries, the ECO start/stop func-
tion is deactivated at the factory due to the
available fuel grade. In this case, the ECO
start/stop function is not available in any
drive program, regardless of the displa yint he
multimedi as ystem display.
Availabl ed rive programs:
C Comfort Comfortabl ea nd economi-
cal driving characteristics
S Sport Sporty driving characteris-
tics
S+ Sport Plus Particularly sporty driving
characteristics
I Individual Individua ls ettings
E Economy Particularly economical
driving characteristics
Additional information for drive programs
( Y
pag e1 25).DYNAMI CS ELEC Tb utton 121
Driving and parking Z

Problems with the transmission Problem
Possible causes/consequences and P Solutions
The transmission has
problems shifting gear. The transmission is losing oil. X
Have the transmission checked at aq ualified specialist workshop
immediately.
The acceleration ability
is deteriorating.
The transmission no lon-
ger changes gear. The transmission is in emergency mode.
It is only partly possible to engage the gears or the transmission is in
position N . X
Stop the vehicle. X
Shift the transmission to position P .X
Switch off the engine. X
Wait at least ten seconds before restarting the engine. X
Shift the transmission to position D or R .X
Have the transmission checked at aq ualified specialist workshop
immediately.
Refueling
Important safety notes
G WARNING
Fuel is highly flammable. If you handle fuel
incorrectly, there is ar isk of fire and explo-
sion.
You must avoid fire, open flames, creating
sparks and smoking. Switch off the engine
and, if applicable, the auxiliary heating before
refueling.
G WARNING
Fuel is poisonous and hazardous to health.
There is ar isk of injury.
You must make sure that fuel does not come
into contact with your skin, eyes or clothing
and that it is not swallowed. Do not inhale fuel
vapors. Keep fuel away from children.
If you or others come into contact with fuel,
observe the following: R
Wash away fuel from skin immediately
using soap and water. R
If fuel comes into contact with your eyes,
immediately rinse them thoroughly with clean water. Seek medical assistance with-
out delay. R
If fuel is swallowed, seek medical assis-
tance without delay .Don ot induce vomit-
ing. R
Immediately change out of clothing which
has come into contact with fuel.
G WARNING
Electrostatic buildu pc an create sparks and
ignite fuel vapors. There is ar isk of fire and
explosion.
Always touch the vehicle body before opening
the fuel filler flap or touching the fuel pump
nozzle. Any existing electrostatic buildu pi s
thereby discharged.
Do not get into the vehicle again during the refu-
eling process. Otherwise, electrostatic charge
could build up again.
! Do not use diesel to refuel vehicles with a
gasoline engine. Do not switch on the ignition
if you accidentally refuel with the wrong fuel.
Otherwise, the fuel will enter the fuel system.
Even small amounts of the wrong fuel could
result in damage to the fuel system and the
engine. Notify aq ualified specialist workshop
and have the fuel tank and fuel lines drained
completely. Refueling 129
Driving and parking Z

Under the following circumstances, the rear
view camera will not function, or will function in
al imited manner: R
if the trunk lid is open R
in heavy rain, snow or fog R
at night or in very dark places R
if the camera is exposed to very bright light R
if the area is lit by fluorescent bulb sorL ED
lighting (the displa ym ay flicker)R
if there is as udden change in temperature,
e.g. when driving into ah eated garage in win-
ter R
if the camera lens is dirty or obstructed
Observe the notes on cleaning
( Y
page 240) R
if the rear of your vehicle is damaged. In this
event, have the camera position and setting
checked at aq ualified specialist workshop
The field of vision and other functions of the rear
view camera may be restricted due to additional
accessories on the rear of the vehicle (e.g.
license plate holder, bicycle rack).
For technical reasons, leaving the standard
height can result in inaccuracies in the guide
lines on vehicles with ah eight-adjustable chas-
sis.
i The rear view camera is protected from rain-
drops and dust by means of af lap. When the
rear view camera is activated, this flap opens.
The flap closes agai nw hen:R
you have finished the maneuvering process R
you switch off the engine R
you open the trunk
Observe the notes on cleaning ( Y
page 240).
For technical reasons, the flap may remain
open briefly after the rear view camera has
been deactivated.
Activating/deactivating the rear view
camera X
To activate: make sure that the SmartKey is
in position 2 in the ignition lock.X
Make sure that the Activation by Rg ear
function is selected in the multimedia system;
see the Digital Operator's Manual. X
Engage reverse gear.
The rear view camera flap opens. The multi-
media system shows the area behind the vehi-
cle with guide lines. The image from the rear view camera is avail-
able throughout the maneuvering process.
To deactivate: the rear view camera deacti-
vates if you shift the transmission to P or after
driving forwards as hort distance.
Displays in the multimedia system The rear view camera may show ad istorted view
of obstacles, show them incorrectly or not at all.
The rear view camera does not show objects in
the following positions: R
very close to the rear bumper R
under the rear bumper R
in close range above the handle on the trunk
lid
! Objects not at ground level may appea rt o
be further awa yt han they actually are, e.g.: R
the bumper of ap arked vehicle R
the drawba rofat railer R
the ball coupling of at railer tow hitchR
the rear section of an HGV R
as lanted post
Use the guidelines only for orientation.
Approach objects no further than the bottom-
most guideline.
C
Yello wg uide line at ad istance of approx-
imately 13 ft (4.0 m) from the rear of the
vehicle
D
White guide line without turning the steering
wheel, vehicle width including the exterior
mirrors (static)

X
Reac hi nt ot he gap, pull hoo dc atch handle D
up and lift hoo d C .
If you lift th eh oo dbya pproximately 15 in
(40 cm), th eh oo diso pened and held open
automatically by th eg as-filled strut .
Closin gt he hoodX
Lowe rt he hoo da nd let it fall from ah eight of
approximately 8in( 20 cm).X
Chec kt ha tt he hoo dh as engage dp roperly.
If th eh oo dc an be raised slightly, it is no t
properly engaged. Open it again and close it
wit hal ittl em or ef orce .
Engine oil
Notes on th eo il levelDependin gony our driving style, th ev ehicl e
consumes up to 0. 9USq t( 0.8 liters )ofo il pe r
60 0m iles (1,000 km). Th eo il cons umption may
be higher than th is when th ev eh icle is ne wori f
you frequently driv eath igh engin es peeds.
Depen din gont he engine, th eo il dipst ick may be
in ad ifferent location.
When checking th eo il leve l:R
park th ev eh icle on al eve ls urfaceR
th ee ng in es hould be swit ched off for appr ox-
imately fiv em in ute sift he engin eisatn orma l
operatin gt em pe ratureR
if th ee ng in eisn ot at normal operatin gt em -
perature, e.g .ift he engin ew as on ly started
brie fly, wait about 30 minute sb efore carrying
out the measurement Checking the oil level using the oil dip-
stick
G WARNING
Certain component sint he engine compart-
ment ,s uch as the engine, radiator and parts
of the exhaust system, can become very hot.
Workin gint he engine compartment poses a
risk of injury.
Where possible, let the engine cool down and
touch only the component sd escribed in the
following.
Example X
Pull oil dipstick C out of the dipstick guide
tube. X
Wipe off oil dipstick C .X
Slowly slide oil dipstick C into the guide tube
to the stop, and take it out again.
If the level is between MIN mark

G WARNING
If engine oil comes into contact with hot com-
ponents in the engine compartment, it may
ignite. There is ar isk of fire and injury.
Make sure that engine oil is not spilled next to
the filler neck. Let the engine cool dow na nd
thoroughly clea nt he engine oil off the com-
ponents before starting the engine.
H Environmental note
When adding oil ,t ake care not to spil la ny. If
oil enters the soil or waterways, it is harmfu lt o
the environment.
! Only use engine oil sa nd oil filters that have
been approved for vehicles with as ervice sys-
tem. You can obtai nal ist of the engine oils
and oil filters tested and approved in accord-
ance with the Mercedes-Benz Specifications
for Service Products at any Mercedes-Benz
Service center.
Damag etot he engine or exhaust system is
caused by the following: R
using engine oil sa nd oil filters that have not
been specifically approved for the service
system R
replacing engine oil and oil filters after the
interval for replacement specified by the
service system has been exceeded R
using engine oil additives.
! Do not add too much oil .Ift he oil leve li s
above the "max" mark on the dipstick, too
much oil has been added. This can lea dt o
damage to the engine or the catalytic con-
verter. Have excess oil siphoned off.
Example :e ngine oil cap X
Turn cap C counter-clockwise and remove it. X
Add engine oil.
If the oil leve lisatorb elow the MIN mark on
the oil dipstick, add 1.1 US qt (1.0 liter) of
engine oil. X
Replace cap C on the filler neck and turn
clockwise.
Ensure that the cap locks into place securely. X
Check the oil leve la gain with the oil dipstick
( Y
pag e2 32).
Further information on engine oil ( Y
pag e2 86).
Checkin ga nd adding other service
products
Checkin gc oo lan tl evel
G WARNING
Certain components in the engine compart-
ment, such as the engine, radiator and parts
of the exhaust system, can become very hot.
Working in the engine compartment poses a
risk of injury.
Where possible ,l et the engine cool dow na nd
touch only the components described in the
following.
G WARNING
The cooling system is pressurized, particularly
when the motor is warm .Ify ou open the cap,
you coul dbes calded if hot coolant sprays out.
There is ar isk of injury.
Let the engine cool dow nb efore you open the
cap. Wea rg love sa nd eye protection. Slowly
open the cap to relieve pressure.
ExampleEngine compartment 233
Maintenance and care Z

X
Park the vehicle on al evel surface.
Only check the coolant level when the vehicle
is on al evel surface and the engine has cooled
down. X
Turn the SmartKey to position 2 in the ignition
lock ( Y
page 115).
On vehicles with KEYLESS-GO, press the
Start/Stop button twice ( Y
page 115).X
Check the coolant temperature gauge in the
multifunction display.
The coolant temperature must be below
158 ‡( 70 †).X
Turn the SmartKey to position 0 ( Y
page 115)
in the ignition lock. X
Slowly turn cap D half at urn counter-clock-
wise to allow excess pressure to escape. X
Turn cap D further counter-clockwise and
remove it.
If the coolant is at the level of marker bar

X
If possible, bring the front wheel si nto the
straight-ahea dp osition.X
Switch off the engine. X
Vehicles without KEYLESS-GO: remove the
SmartKey from the ignition lock. X
Vehicles with KEYLESS-GO: open the driv-
er's door.
The on-board electronics now have status 0 .
This is the same as the SmartKey having been
removed. X
Vehicles with KEYLESS-GO: remove the
Start/Stop button from the ignition lock
( Y
page 115).X
Make sure that the passengers are not endan-
gered as they do so. Make sure that no one is
near the danger area whil eaw heel is being
changed. Anyone who is not directly assisting
in the wheel change should, for example,
stand behind the barrier. X
Get out of the vehicle .P ay attention to traffic
conditions when doing so. X
Clos et he driver's door.
MOExtended tires (tires with run-flat
properties)
General notes With MOExtended tires (tires with run flat char-
acteristics), you can continue to drive you rv ehi-
cle even if there is at otal loss of pressure in one
or more tires. The affected tire must not show
any clearl yv isible damage.
You can recognize MOExtended tires by the
MOExtended marking which appears on the
sidewall of the tire. You wil lf ind this marking
next to the tire size designation, the load-bear-
ing capacity and the speed index ( Y
page 269).
MOExtended tires may only be used in conjunc-
tion with an active tire pressure loss warning
system or with an active tire pressure monitor.
If ap ressure loss warning message appears
in the multifunction display: R
observe the instructions in the display mes-
sages ( Y
page 196).R
check the tire for damage. R
if driving on, observe the following notes.
The driving distance possible in run-flat mode is
approximately 50 miles (80 km) when the vehi-
cle is partially laden and approximately 19 miles
(30 km) when the vehicle is full yl aden. In addition to the vehicle load ,t he driving dis-
tance possible depends upon: R
vehicle speed R
road condition R
outsid et emperature
The driving distance possible in run-flat mode
may be reduced by extreme driving conditions
or maneuvers, or it can be increased through a
moderate style of driving.
The driving distance possible in run-flat mode is
counted from the moment the tire pressure loss
warning appears in the multifunction display.
You must not exceed am aximum speed of
50 mph (80 km/h).
When replacing one or all tires, please observe
the following specifications for you rv ehicle's
tires: R
size R
type and R
the "MOExtended" mark
If at ire has gone flat and cannot be replaced
with aM OExtended tire, as tandard tire may be
used as at emporary measure. Make sure that
you use the proper size and type (summe ro r
winter tire).
Vehicle se quipped with MOExtended tires are
not equipped with aT IREFIT kit at the factory. It
is therefore recommended that you additionally
equi py ou rv ehicle with aT IREFIT kit if y ou mount
tires
that do not feature run-flat properties, e.g.
winter tires. AT IREFIT kit is available, for exam-
ple, from aq ualifie ds pecialist workshop.
Important safety notes
G WARNING
When driving in emergency mode, the driving
characteristics deteriorate, e.g. when corner-
ing, accelerating quickly and when braking.
There is ar isk of an accident.
Do not exceed the stated maximum speed.
Avoid abrupt steering and driving maneuvers,
and driving over obstacle s( curbs, potholes,
off-road). This applies in particular to al aden
vehicle.
Stop driving in emergency mode if: R
you hear banging noises. R
the vehicle starts to shake.242
Flat tire
Breakdow na ssistance

The vehicle will then use very little energy, thus
conserving battery power.
If the power supply has been interrupted, e.g. if
you reconnect the battery, you will have to: R
reset the function for automatically folding
the exterior mirrors in/out by folding the mir-
rors out once ( Y
page 89)R
set the clock (see the Digital Operator's Man-
ual)
On vehicles with am ultimedia system, the
time is set automatically.
Charging the battery
G WARNING
During charging and jump-starting, explosive
gases can escape from the battery. There is a
risk of an explosion.
Particularly avoid fire, open flames, creating
sparks and smoking. Ensure there is sufficient
ventilation while charging and jump-starting.
Do not lean over ab attery.
G WARNING
Battery acid is caustic. There is ar isk of injury.
Avoid contact with skin, eyes or clothing. Do
not inhale any battery gases. Do not lean over
the battery. Keep children away from batter-
ies. Wash away battery acid immediately with
plenty of clean water and seek medical atten-
tion.
G WARNING
Ad ischarged battery can freeze at tempera-
tures below freezin gp oint. When jump-start-
ing the vehicle or charging the battery, gases
can escape from the battery. There is ar isk of
an explosion.
Allow the frozen battery to thaw out before
charging it or jump-starting.
! Only use battery chargers with am aximum
charging voltage of 14.8 V.
! Only charge the battery using the jump-
starting connection point.
The jump-starting connection point is in the
engine compartment. If the indicator/warning lamps do not light up at
low temperatures, it is very likely that the dis-
charged battery has frozen. In this case, you
may neither charge the battery nor jump-start
the vehicle. The service life of at hawed-out bat-
tery may be shorter .T he starting characteristics
can be impaired, particularly at low tempera-
tures. Have the thawed-out battery checked at a
qualified specialist workshop.
Read the battery charger's operating instruc-
tions before charging the battery. X
Open the hood. X
Connec tt he battery charger to the positive
terminal and ground point in the same order
as when connectin gt he donor battery in the
jump-starting procedure ( Y
page 249).248
Battery (vehicle)
Breakdown assistance