light MERCEDES-BENZ SLK-Class 2007 R171 Comand Manual

102 Telephone*
Phone book
The following options are now available:
Switching between number and name
display
Selecting a phone book entry and es-
tablishing a connection (
page 102)
Deleting a phone book entry
(
page 103)
Switching between number and name
display
Open the phone book from COMAND
(
page 101).
Press the 123 soft key.
The phone book switches to number
display. The status bar shows the name
of the highlighted entry;
or
Press the ABC soft key.
The phone book switches to name dis-
play. The status bar shows the number
of the highlighted entry.
On the COMAND control unit
Open the phone book (page 101).
The list of phone book entries stored
on your cell phone appears.
Changing initials:
Press# or $ once or repeatedly.
Each time you press the button, the
display changes to the next letter up or
down. At the end of the list of letters is the
category
Other. This category combines
all entries without a name, or entries
whose names start with a special char-
acter (e.g.
* or #).
Selecting an entry:
If necessary, change the initial.
Select an entry using % or &.
If you press and hold either one of the
buttons, the scrolling up or down accel-
erates.
Establishing a connection:
Press2.
The telephone initiates the connection
with the selected number.
Selecting a phone book entry and es-
tablishing a connection

108 Navigation*
Important notes
Safety instructions
WarningG
For safety reasons, you should only enter a
destination when the vehicle is stationary.
When the vehicle is in motion, a passenger
should enter the destination. Study manual
and select route before driving.
Do not watch display screen or operate but-
tons while the vehicle is in motion - let navi-
gation announcements guide you. Stop at a
safe location before using buttons or mak-
ing corrections.
Traffic regulations always have priority over
any route recommendations given.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
WarningG
The route calculated by COMAND is a rec-
ommendation on how to best reach your se-
lected destination.
During route guidance, you will not receive
any information on
Traffic lights
Stop and yield signs
Parking or stopping zones
One-way streets
Narrow bridges
Similar traffic regulation data
You should therefore always strictly observe
traffic regulations while driving. Drive care-
fully and always obey traffic laws and road
signs even if they contradict COMAND in-
structions.
WarningG
The Navigation DVD module contains a
Class 1 laser product. There is a danger of
invisible laser radiation if the cover is
opened or damaged.
Do not remove the cover. The Navigation
DVD module does not contain any parts
which can be serviced by the user. For safe-
ty reasons, have any service work which
may be necessary performed only by quali-
fied personnel.

133 Navigation*
Route guidance
The road currently travelled on is indicated
in the status bar at the bottom, in this ex-
ample
I-80 E (Interstate 80 East).
The information 1.2 mi on the very right in-
dicates the distance to the next driving ma-
neuver.
The circle shows the current vehicle lo-
cation. The arrow in the circle designates
the current driving direction.
The remaining route is highlighted in color. Display example 2
On the right-hand side of the display the
symbol for the next driving maneuver is in-
dicated (here left turn).On the very right is shown a distance bar.
The dark blue part of the bar and the infor-
mation 700ft, in this example, indicate the
distance to the next driving maneuver.
If available, the street following the driving
m a n e u v e r w i t h i t s n a m e i s s h o w n i n t h e t o p
status bar (here
CHESTNUT RIDGE RD).
The destination is marked with a flag on
the map, any stop-over destination is
marked with a flag .
Changing map scalei
The display unit can be changed to km
or miles using the control system (see
your vehicle Operator's Manual).
When the display unit is set to miles,
the COMAND will indicate distances in
miles (mi) or feet (ft).
When the display unit is set to km, the
COMAND will indicate distances in kilo-
meters (km) and meters (m).
i
The colored highlight only appears
when the system has completed the
route calculation.
s

136 Navigation*
Route guidance
If the destination is within a partially
digitized area
COMAND guides you through fully digitized
areas for as long as possible. Route guid-
ance is conducted in the usual manner, i.e.
with navigation announcements and route
guidance displays.
Before the vehicle reaches a partially digi-
tized area, COMAND notifies you of this
with the following announcements:
“Be prepared to enter an area where
turn by turn guidance cannot be provid-
ed.”
“In 700 feet you will enter an area
where turn by turn guidance cannot be
provided.”
“You are about to enter an area where
turn by turn guidance cannot be provid-
ed.”
Route guidance within a partially digi-
tized area
If you start route guidance in this type of
area, you will hear the following announce-
ment: “You are currently in an area where
turn by turn guidance cannot be provided.”Route guidance is provided by means of a
direction arrow showing the compass
heading to the destination. COMAND will
not generate automatic navigation an-
nouncements.
If you try to call up or repeat an announce-
ment manually, (
page 132) you will hear
the announcement “You are currently in an
area where turn by turn guidance cannot be
provided.“.
During route guidance, the display is divid-
ed. On the right-hand side you will see the
direction arrow showing the compass
heading to the destination.
O n t h e l e f t - h a n d s i d e o f t h e d i s p l a y y o u w i l l
see the map with the suggested route. The
suggested route is highlighted blue. How-
ever, it may not be possible to follow the
suggested route because, for example, the
road is closed or not open for car traffic.
If, during route guidance, COMAND leads
you back into a fully digitized area, route
guidance will simply continue in the usual
manner.
i
The indicated distance can be seen
here by way of example. In reality, it
may be different.
i
When you call up the info menu to this
type of destination, (
page 139) the
following data shown there may differ
from the actual situation:
Estimated time of arrival
Remaining driving time to the desti-
nation
Remaining distance to the destina-
tion

137 Navigation*
Route guidance
Route guidance to an off-road destina-
tionCOMAND can guide you to destinations
within the area covered by the digital map,
even if a destination is not located at a
road known to the system.
These destinations are shown as off-road
destinations, which you can enter using
the map, for example.
I n t h e s e c a s e s , C O M A N D g u i d e s y o u f o r a s
long as possible with navigation announce-
ments and displays on roads known to the
system.
Shortly before you reach the last known
point in the digitized road network, you will
hear the announcement “The destination is
nearby. Follow the arrow on the display”.
You will then see an arrow that indicates
the direction to the off-road destination.
When the off-road destination is close to
the road,
Area of dest. reached a p p e a r s i n a d -
dition below the arrow.When you leave the last known point in the
digitized road network, direction arrows
showing the compass heading to the desti-
nation guide you. You will also see the
Di-
rection to destination
display.
Route guidance from an off-road loca-
tion to a destination
If there is no road available on map at cur-
rent position of the car, vehicle is off road.
C O M A N D i s a l s o a b l e t o g u i d e y o u t o a d e s -
tination from such a location.
At the start of the route guidance, you will
see the
Off Road message and a direction
arrow. The direction arrow shows the com-
pass heading to the actual destination.
The route is highlighted blue from the near-
est road known to the system.
As soon as the vehicle is back on a road
known to the system, route guidance con-
tinues in the usual way.
Off-road and off-map
WarningG
The COMAND navigation system may direct
you to off-road routes that your vehicle may
n o t b e c a p a b l e o f t r a v e r s i n g t h r o u g h w i t h o u t
damaging your tires, wheels or vehicle. It is
the driver’s sole responsibility to determine
the suitability of the route. Off-road routes
may be of varying conditions and their ap-
propriateness for use may be affected by
various factors such as time of day, time of
year and immediate weather conditions that
cannot be judged or taken into consider-
ation by the COMAND system.

138 Navigation*
Route guidance
Route guidance from an off-map loca-
tion to a destination
If the vehicle position is outside the area
covered by the digital map, then the vehi-
cle is in an off-map location.
C O M A N D i s a l s o a b l e t o g u i d e y o u t o a d e s -
tination from such a location.
At the start of the route guidance, you will
see the
Off Map message and a direction ar-
row. The direction arrow shows the com-
pass heading to the actual destination.
The route is highlighted blue from the near-
est road known to the system.
As soon as the vehicle is back on a road
known to the system, route guidance con-
tinues in the usual way.Off-road during route guidance
The road layout may differ from the data on
the digital map, due to road construction
measures, for example.
In such cases, the system cannot allocate
the vehicle’s position to the digital map
and the vehicle is therefore in an off-road
position.
The Off Road message and an arrow show-
ing the compass heading to the destina-
tion appear on the display.
As soon as the system can allocate the ve-
hicle position’s to the map again, route
guidance continues in the usual way.

140 Navigation*
During route guidance
1Estimated time of arrival
2Remaining driving time in hours and
minutes
3Remaining journey (distance)
1, 2 and 3 refer to the stop-over desti-
nation. You'll only see the details for the fi-
nal destination when you arrive at your
stopover and the system has calculated
the route to the main destination.Selectable soft keysRoute soft key:
Provides access to the display of the
route on the map,
Mode soft key:
Provides access to the setting of the
route mode (
page 113).
In the Info menu, press the Route soft
key.The map appears. The route remaining
is highlighted in blue.
The destination is marked with a flag
, any stop-over destination is marked
with a flag . The current vehicle posi-
tion is identified with the symbol.
Depending on the distance to the des-
tination, it may take some time before
the route display appears.
i
The estimated time of arrival does not
refer to the time zone of destination,
but always refers to the time zone of
the vehicle's current location. For a
correct calculation, make sure that the
system clock is set correctly
(
page 166).
Displaying the route on the map
s

159 Navigation*
POIs (Points of Interest)
Press the Details soft key if you want to
see details of a selected POI.
The details disappear after
approx. 3 seconds, or when pressing
the
Details soft key again.
Press '.
The Start Route Guidance menu
(
page 131) appears.
Press 5;
or
In the Destination entry menu
(
page 118), press the Map soft key.
The full-screen map appears. Symbols
indicate the POIs.
If required, use#, $, %, &, 6
or 8 to move the map.
If the soft key displays are hidden,
press any soft key.
The soft key displays appear.
Press the Symbol soft key.
A POI is selected and highlighted in col-
or. Its name appears in the status bar.
Selecting a POI using the map
i
Th e P O I s y m b o l s t o b e d i s p l a y e d c a n b e
selected (
page 147).
POI symbols are indicated only if the
map scale is set to 0.05 mi (50 m), 0.1
mi (100 m), 0.2 mi (200 m), or 0.5 mi
(500 m).
To change the map scale (
page 133).


166 System
System settings
Press<.
The System menu appears.
Selectable soft keys
Time soft key
For setting the date and time
Lang. soft key
For setting the language (
page 168)
Tones soft key
For switching confirmation beeps
and acoustic signals ON and OFF
(
page 168)
Display soft key
For changing the display settings
(
page 169)
Reset soft key
For resetting COMAND to the factory
settings (
page 170)
Press the Time soft key.
The Date/Time setting menu appears.
The following options are now available:
Setting the time
Setting the date
Setting the date/time format
Setting the time
The UTC time transmitted by the GPS sat-
ellites has to be set to the local time zone.
This enhances:
correct navigation for routes with time-
dependent traffic guidance, and
correct calculation of the estimated
time of arrival.
Calling up the System menu
Setting the date/time
i
There is no automatic change from day-
light saving time to standard time.
This has to be changed manually.
When you change the time zone, the
clock time also changes automatically.
If you enter an incorrect time, the time
difference remains unchanged when
you change time zone.