engine MERCEDES-BENZ SLR CLASS 2007 Workshop Manual

196 Controls in detail
Automatic climate control
Air recirculation mode with conve-
nience closing or opening feature
Activating
Press and hold button,.
The indicator lamp on the button
comes on. The air recirculation mode is
activated. The windows will close.Deactivating
Press and hold button,.
The indicator lamp on the button goes
out. The air recirculation mode is deac-
tivated. The windows will return to their
previous position.
Air conditioning
The air conditioning (cooling) function is
operational when the engine is running and
cools the vehicle interior down to the se-
lected temperature. In addition, the cool-
ing function dehumidifies the air in the
vehicle interior, thus preventing the
windows from fogging up.
Warning!G
Never operate the windows if there is the
possibility of anyone being harmed by the
closing procedure.
In the event that the procedure causes po-
tential danger, the closing of the windows
can be immediately halted by releasing
the, button or by pressing and pulling
the respective window switch.
iA window will only return to its previous po-
sition if it has not moved to another position us-
ing the respective window switch after it was
closed with button,.
Warning!G
If you turn off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog
up more quickly. Window fogging may
impair visibility and endanger you and/or
others.
iCondensation may drip out from underneath
the vehicle. This is normal and not an indication
of a malfunction.

197 Controls in detail
Automatic climate control
Deactivating
It is possible to deactivate the cooling
function of the automatic climate control
system. The air in the vehicle will then no
longer be cooled or dehumidified.
Press ± button (page 188).
The indicator lamp on the ±
button comes on. The cooling function
switches off after a short delay.Activating
Moist air can fog up the windows. You can
dehumidify the air with the air
conditioning.
Press ± button again (page 188).
The indicator lamp on the ± button
goes out.
The air conditioning uses the refrigerant
R134A. This refrigerant is free of CFCs
which are harmful to the ozone layer.
Residual heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.
iUnder certain circumstances, e.g. when the
fuel system is too hot and needs to be cooled,
the cooling switches on again automatically. The
red lamp on the ± button the automatic
climate control panel flashes.
After cooling the fuel system sufficiently, the air
conditioning switches off again and the red lamp
stops flashing.
!If you press the ± button on the auto-
matic climate control panel and it starts to flash,
this indicates that the air conditioning is losing
refrigerant. The compressor has turned off. The
air conditioning cannot be turned on again.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Center.
iHow long the system will provide heating
depends on the coolant temperature and the
selected temperature. The blower will run at low
speed regardless of the air distribution control
setting.

204 Controls in detail
Driving systems
1Sets current or higher speed
2Sets current or lower speed
3Cancels the cruise control
4Resumes at last set speed
Setting current speed
Accelerate or decelerate to the desired
speed.
Briefly lift1 or depress2 the cruise
control lever.
The current speed is set.
Remove your foot from the accelerator
pedal.
The cruise control is activated.
Canceling the cruise control
There are several ways to cancel the cruise
control:
Step on the brake pedal.
The cruise control is canceled. The last
speed set is stored for later use.
or
Briefly push the cruise control lever to
position3.
The cruise control is canceled. The last
speed set is stored for later use.The cruise control is automatically can-
celled, when

the vehicle speed is below 20 mph
(30 km/h)

ESP® is in operation or switched off
with the ESP® switch (page 86)

you move the gear selector lever to
positionN while driving
iOn uphill or downhill grades, the cruise
control may not be able to maintain the set
speed. Once the grade eases, the set speed will
be resumed.
!However, the gear selector lever should not
be moved to neutralN while driving, except to
coast when the vehicle is in danger of skidding
(e.g. on icy roads).
iDepressing the accelerator pedal does not
deactivate the cruise control. After brief acceler-
ation (e.g. for passing), the cruise control will re-
sume the last speed set.
The last stored speed is canceled when you turn
off the engine.

205 Controls in detail
Driving systems
Setting a higher speed
Lift the cruise control lever to
position1 and hold it up until the de-
sired speed is reached.
Release the cruise control lever.
The new speed is set.
Setting a lower speed
Depress the cruise control lever to
position2 and hold it down until the
desired speed is reached.
Release the cruise control lever.
The new speed is set.Fine adjustment in 1 mph
(Canada: 1 km/h) increments
Faster
Briefly tip the cruise control lever in
direction of arrow1.
Slower
Briefly tip the cruise control lever in
direction of arrow2.Setting to last stored speed
(“Resume” function)
Briefly push the cruise control lever to
position4.
The cruise control resumes the last set
speed.
Remove your foot from the accelerator
pedal.
iDepressing the accelerator pedal does not
deactivate the cruise control. After brief acceler-
ation (e.g. for passing), the cruise control will
resume the last speed set.
iWhen you use the cruise control lever to de-
celerate, the transmission will automatically
downshift if the engine’s braking power does not
brake the vehicle sufficiently.
Warning!G
The speed stored in memory should only be
set again if prevailing road conditions per-
mit. Possible acceleration or deceleration
differences arising from returning to preset
speed could cause an accident and/or
serious injury to you and/or others.

209 Controls in detail
Useful features
Power outlet
The power outlet is located on the left side
in the trunk.
1Power outlet
Switch on the ignition (page 40).
Flip up cover and insert electrical plug
(cigar lighter type).
Telephone
The telephone is located in the center
storage compartment (
page 207).
!The lighter socket can accommodate
12V DC electrical accessories (up to a maximum
of 85 W) designed for use with the standard
“cigarette lighter” plug type. Keep in mind, how-
ever, that connecting accessories to the lighter
socket (for example extensive connecting and
disconnecting, or using plugs that do not fit prop-
erly) can damage the lighter socket. With the
socket damaged, the lighter may no longer be
able to be placed in the heating (pushed-in) posi-
tion, or the lighter may pop out too early with the
lighter not hot enough.
To help avoid damaging the cigarette lighter
socket, we recommend connecting 12V DC elec-
trical accessories designed for use with a stan-
dard “cigarette lighter” plug type to the
12 V power outlets in your vehicle whenever
possible.
iThe power outlet can be used to accommo-
date 12V DC electrical accessories (e.g. air
pump, auxiliary lamps) up to a maximum
of 180 W or as a battery charging point
(
page 368).
Warning!G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and personal
injury.

222 Controls in detail
Useful features
Programming the integrated remote
control
Step 1:
Switch on the ignition (page 40).Step 2:
If you have previously programmed a
signal transmitter button and wish to
retain its programming, proceed to
step 3.
If you are programming the integrated
remote control for the first time, press
and hold the two outer signal transmit-
ter buttons2 and4 and release
them only when indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory.
If you later wish to program a second
and/or third hand-held transmitter to
the remaining two signal transmitter
buttons, do not repeat this step and
begin directly with step 3.Warning!G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
- signaling the door to stop and reverse -
does not meet current U.S. federal safety
standards.
When programming a garage door opener, it
is advised to park the vehicle outside the
garage.
Do not run the engine while programming
the integrated remote control. Inhalation of
exhaust gas is hazardous to your health. All
gas contains carbon monoxide (CO), and in-
haling it can cause unconsciousness and
possible death.

228 Controls in detail
Useful features
Installing
Example driver’s side
1Eyelet
2Retainer pins
Lay down the floormat.
Press eyelets 1 onto retainers pins2
in direction of arrow. Removing
Pull the floormats off retainers pins.
Remove the floormat.
Dust cover!To avoid damage to the carbon fiber surface
please make sure your shoe soles are free of
hard particles (e.g. stones, glass) and avoid the
use of small surface heels when driving the
vehicle.
Warning!G
Allow the engine to cool down completely
before slipping the dust cover on your vehi-
cle. Otherwise you could be seriously
burned when coming into contact with the
hot exhaust system.
!To avoid damage to the vehicle and the dust
cover, observe the following:

Use the dust cover only when the vehicle is
garaged.

Cover the vehicle only when the engine has
cooled down completely.

The vehicle as well as the dust cover must be
dry before slipping the dust cover on the
vehicle.

Make sure the dust cover is clean and dry
before inserting it in the bag provided with
the dust cover.
iClean the dust cover according to the care
label on the inside of the dust cover.

Operation
The first 1000 miles (1500 km)
Driving instructions
At the gas station
Engine compartment
Trunk
Tires and wheels
Winter driving
Maintenance
Vehicle care

234 Operation
In the “Operation” section you will find
detailed information on operating, main-
taining and caring for your vehicle.
The first 1000 miles (1500 km)
The more cautiously you treat your vehicle
during the break-in period, the more satis-
fied you will be with its performance later
on. You should therefore observe the fol-
lowing for the first 1000 miles (1500 km):

Drive at varying but moderate road and
engine speeds.

Do not drive faster than 150 mph
(240 km/h).

Break in new tires for the first
100 miles (160 km), therefore avoid
high-speed cornering. Do not exceed a
speed of 125 mph (200 km/h).

Do not drive at engine speeds above
4500 rpm.

Try to avoid heavy load on the engine
(driving at full throttle) and driving at
high engine speeds (maximum of
2/3
of top speed of each gear) during this
break-in period.

Avoid accelerating by kick-down.

Change gears in good time.

Do not attempt to slow the vehicle
down by shifting to a lower gear using
the gear selector lever.

Select positions3,2 or1 only when
driving at moderate speeds (for hill
driving).
After 1000 miles (1500 km), you may grad-
ually bring the vehicle up to full road and
engine speed.
All of the above instructions also apply
when driving the first 1000 miles
(1500 km) after the engine or the rear
differential has been replaced.
iAlways obey applicable speed limits.

235 Operation
Driving instructions
Driving instructions
Drive sensibly – save fuel
Fuel consumption, to a great extent,
depends on driving habits and operating
conditions.
To save fuel you should:

Keep tires at the recommended tire
inflation pressures.

Remove unnecessary loads.

Allow engine to warm up under low
load use.

Avoid frequent acceleration and
deceleration.

Have all maintenance work performed
at the intervals specified in the
Maintenance Booklet and as required
by the maintenance service display.
Contact an authorized Mercedes-Benz
Center.
Fuel consumption is also increased by
driving in cold weather, in stop-and-go
traffic, on short trips and in hilly area.
Drinking and drivingPedals
Warning!G
Drinking and driving and/or taking drugs
and driving are very dangerous combina-
tions. Even a small amount of alcohol or
drugs can affect your reflexes, perceptions
and judgment.
The possibility of a serious or even fatal
accident are greatly increased when you
drink or take drugs and drive.
Do not drink or take drugs and drive or allow
anyone to drive who has been drinking or
taking drugs.
Warning!G
Make sure that absolutely no objects are ob-
structing the pedals’ range of movement.
Keep the driver’s footwell clear of all obsta-
cles. If there are any floormats or carpets in
the footwell, make sure that the pedals still
have sufficient clearance.
During sudden driving or braking maneuvers
the objects could get caught between the
pedals. You could then no longer brake or
accelerate. This could lead to accidents
and/or injury.