clock Mercury Grand Marquis 1996 s User Guide

206 [RE08570( ALL)05/92]NOTE: Never use the differential housing as a
lift point.
% [RE08700( GV)11/90]
quarter page art:0010687-A
Jacking locations
[RE08725( GV)03/92]
quarter page art:0010688-A
Locating the notch for the jack Ð rear wheels
[RE08750( GV)03/92]
quarter page art:0010689-A
Locating the notch for the jack Ð front wheels
*
[RE08900( ALL)01/95]
2. Turn the jack handle clockwise until the
wheel clears the ground. Remove the wheel
lug nuts.
File:rcreg.ex
Update:Thu Feb 1 08:33:27 1996

207 [RE08915( GV)01/96]
3. If you are replacing the front tire (with
aluminum wheels) with the temporary spare
tire, you need to remove the black dust
shield. Gently pull the shield over the rubber
o-rings and slide it off the wheel studs.
Because the rubber o-rings are soft, they
should pass through the holes in the shield.
If the rings do not pass through the holes,
remove them from the wheel studs. Save the
black dust shield for future use, and ensure
the rubber o-rings are removed from wheel
studs.
*
[RE08925( GV)01/96]
4. Replace the flat tire with the spare tire,
making sure that the air valve stem is facing
outward.
*
[RE08945( GV)01/96]
5. Reinstall the lug nuts, tightening until the
wheel is snug against the hub. The beveled
edges on the lug nuts face inward. Do not
fully tighten the lug nuts until you lower the
vehicle. If you do, you could force the
vehicle off the jack.
*
[RE08965( GV)01/96]
6. Lower the vehicle by turning the jack handle
counterclockwise.
*
[RE08985( GV)01/96]
7. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration. As soon as possible, have your
dealer or a qualified service technician check
the lug nuts for proper torque specifications.
% [RE09100( ALL)03/93]
quarter page art:0010350-A
The lug nuts on the wheel
File:rcreg.ex
Update:Thu Feb 1 08:33:27 1996

239 %
*
[SV05850( ALL)04/95]
Cleaning the Engine
*
[SV06000( ALL)04/95]
A clean engine is more efficient because a
buildup of grease and dirt acts as an insulator,
keeping the engine warmer than usual.
*
[SV06020( ALL)05/95]
q
Extreme care must be used if a power washer
is used to clean the engine. The high pressure
fluid could penetrate sealed parts and
assemblies causing damage or malfunctions.
*
[SV06040( ALL)04/95]
q
In order to avoid possible cracking of the
engine block or fuel injection pump, do not
spray a hot engine or injection pump with
cold water.
*
[SV06060( ALL)04/95]
q
The alternator, distributor and air intake must
be covered. Covering these components will
help prevent water damage.
*
[SV06080( ALL)04/95]
q
Never wash or rinse the engine while it is
running. Water getting into the engine may
cause internal damage.
%
*
[SV06100( ALL)03/95]
Filling the Fuel Tank
*
[SV06220( GV)01/95]
The fuel filler door is outside the vehicle on the
driver's side near the back. To fill the fuel tank:
[SV06550( ALL)05/95]
1. After opening the fuel filler door, remove
the cap carefully and slowly by turning it
counterclockwise 1/2 to 3/4 turn.
[SV06650( ALL)05/95]
RWARNING
The fuel system may be under pressure. If
the fuel cap is venting vapor or if you
hear a hissing sound while disengaging
the fuel cap, wait until it stops before
completely removing the cap. Otherwise,
fuel may spray out and injure you or
others.
File:rcsvg.ex
Update:Wed Jun 28 16:19:38 1995

240 [SV06700( ALL)05/95]2. Put the nozzle all the way inside the fuel
filler pipe before pumping the fuel.
[SV06800( ALL)05/95]
NOTE: If you spill any fuel on the body of
your vehicle, clean it off immediately.
The fuel may dull or soften the paint
if you do not wash it off.
[SV06850( ALL)05/95]
3. Replace the fuel cap completely when you
are finished. Turn it clockwise 1/4 turn until
it is tight. It will click when it is fully
tightened.
[SV06875( ALL)05/95]
4. Push the fuel door closed.
[SV06900( ALL)05/95]
RWARNING
If you lose the fuel cap, replace it with a
Motorcraft or equivalent fuel cap. If you
do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly
in a collision, endangering you and your
passengers.
[SV06950( ALL)05/95]
NOTE: If you replace your fuel cap with an
aftermarket fuel filler cap, the customer
warranty may be void for any damage
to the fuel tank and/or fuel system.
[SV07500( ALL)05/95]
Choosing the Right Fuel
[SV07600( ALL)05/95]
Use only UNLEADED FUEL in your vehicle.
Using leaded fuel is prohibited by federal law.
Your warranty may not apply if your vehicle is
damaged because you used the wrong fuel.
[SV07701( ALL)05/95]
Using a high-quality fuel makes your vehicle
more responsive and maintain its good fuel
economy and emissions. It should not be
necessary to add any aftermarket products to
your fuel tank if you continue to use a
high-quality fuel.
File:rcsvg.ex
Update:Wed Jun 28 16:19:38 1995

251 [SV19010( GV)05/95]
RWARNING
Never remove the pressure cap while the
engine is running or hot.
[SV19030( ALL)05/95]
Follow these steps to avoid personal injury that
can be caused by escaping steam or engine
coolant.
*
[SV19060( GV)01/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the
pressure cap.
[SV19145( ALL)03/95]
2. When the engine is cool, wrap a thick towel
around the cap and turn it slowly
counterclockwise to unscrew.
*
[SV19150( ALL)03/95]
3. Step back while the pressure releases.
[SV19160( ALL)12/94]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it, and remove it.
*
[SV19175( GV)02/95]
5. Stand away from the reservoir opening. Hot
steam may blow out or hot engine coolant
may even splash out.
*
[SV19190( ALL)03/95]
To find out how much engine coolant mixture
your vehicle's coolant system can hold, seeRefill
capacities for fluidsin the Index.
% [SV19200( ALL)12/94]
Add engine coolant only to the recovery
reservoir.If the coolant level is low, add a 50/50
or appropriate mixture of water and the type of
engine coolant that Ford specifies. You may add
water by itself only in an emergency, but you
should replace it with a 50/50 or appropriate
mixture as soon as possible.
*
[SV19300( ALL)01/95]
Have your dealer check the engine cooling
system for leaks if you have to add more than a
quart (liter) of engine coolant more than once a
month.
File:rcsvg.ex
Update:Wed Jun 28 16:19:38 1995

284 % [SV48900( BCGV)06/94]Toremovethe high-mount brakelamp:
[SV49400( GV)06/94]
1. Remove the two retaining screws with a
Phillips screwdriver.
[SV49800( GV)10/90]
2. Then lift the whole assembly up and over
the retaining brackets. Do not move upper
part of plastic attachment brackets.
[SV50010( GV)06/94]
3. Twist socket counterclockwise to remove
from lamp.
[SV50020( GV)06/94]
4. Pull bulb out of socket.
[SV50250( GV)06/94]
5. Replace the burned out bulbs.
*
[SV50300( BCGV)02/95]
Toinstallthe high-mount brakelamp:
[SV50600( GV)10/90]
1. Position the brakelamp over the retaining
brackets.
[SV50900( GV)01/89]
2. Install and tighten the two retaining screws.
File:rcsvg.ex
Update:Wed Jun 28 16:19:38 1995

316 Index
Chime
key in ignition............. 38
safety belt............. 51,65
Circuit breakers
checking and replacing........ 279
see also fuses............. 271
Cleaning your vehicle
chrome and aluminum parts....... 6
engine compartment.......... 239
exterior................ 5
exterior lamps............ 103
fabric................ 139
headlamps.............. 103
instrument panel............ 88
instrument panel lens......... 110
interior lamps............. 109
mirrors................ 141
plastic parts.............. 6
polishing................ 6
rustproofing.............. 6
safety belts............... 17
tail lamps.............. 103
upholstery and interior trim...... 139
washing................ 5
wheels................ 266
Climate control system
air conditioning........... 88,90
electronic automatic
temperature control.......... 90
heating............... 88,90
Clock.................. 110
Cold engine starting............ 40
Coolant (see Engine coolant)
checking and adding......... 249
drain and flush............ 253
preparing for storage......... 295
proper solution............ 251
refill capacities............ 291
refill procedure............ 253
specifications............. 293
temperature gauge......... 58,64
File:rcixg.ex
Update:Wed Jan 31 09:58:27 1996