radio Mercury Sable 1997 Audio Guide

control more than three seconds results in fast
rewind.
Fast forward function
The fast forward control (FF) works in tape and CD
modes (if equipped).
Fast forward in tape mode
After pressing FF, the radio plays until the fast
forward function is stopped (with the tape play
select control or the fast forward control) or the end
of the tape is reached.
At the end of the first side of the tape, direction
automatically reverses and the opposite side of the
tape plays.
Fast forward function in the CD mode
Pressing FF for less than three seconds results in
slow forward action.
Pressing FF for more than three seconds results in
fast forward action.
Tape direction select
Press SIDE 1±2 to play
the alternate side of a
tape.
Tape eject
Press EJECT to stop
and eject a tape.
SIDE 1-26
SIDE 1-24
EJ
com_fast_forward.01
dno_fast-foward-in-tape
com_fast_forward_cd.01
com_tape_direction_select.01
dno_tape-eject
com_dolby_reduction.01
Controls and features
13

The magazine does no
need to be full for the
changer to operate.
Insert the loaded
magazine into the
changer. Make sure it is
fully inserted. Slide the
access door closed.
Radio power must be turned on to play the CDs in
the changer. The magazine may be stored in the
glove box when not being used. Slide the access
door on the changer closed when not in use.
The CD magazine may be inserted or ejected with
the radio power off.
Controls and features
16

Display Information
Indicates Dolby Noise Reduction
activation
Indicates Tape play
CD-## Indicates CD number playing
(e.g., CD-01, CD-02, etc.)
TR-## Indicates CD track number
playing (e.g., TR-01, TR-02, etc.)
##-## Indicates CD number and track
number playing (e.g., 03-10
means disc 3-track 10, etc.)
NO DISC Indicates CD changer is empty
C Indicates CD compression factor
activation
NO CD Indicates empty slot, mechanical
error, unreadable disc, focus
error.
NO DJ Indicates CD changer not
connected or not communicating
AM, FM1 or FM2 Indicates which frequency band
the audio system is in
87.9 to 107.9
(530 to 1610
AM)Indicates currently playing radio
station
STIndicates stereo operation
Illuminated bars Indicates volume, relative level of
bass and treble and relative levels
of speaker balance and fade
TD E1 Indicates possible problem tape
TD E2 Radio cannot eject tape
TD E3 Radio cannot insert tape properly
TOO HOT Changer's internal temperature is
above 60ÉC (140ÉF)
The display screen gives information on the status of
the audio system.
dno_display-chart
Display
17

CLEANING CASSETTE PLAYER
Clean the tape player head with a cassette cleaning
cartridge after ten to twelve hours of play to
maintain the best sound and operation.
CASSETTE AND CASSETTE PLAYER CARE
²Use only cassettes that are 90 minutes long or
less.
²Do not expose tapes to direct sunlight, high
humidity, extreme heat or extreme cold. Allow
tapes that may have been exposed to extreme
temperatures to reach a moderate temperature
before playing.
²Tighten very loose tapes by inserting a finger or
pencil into the hole and turning the hub.
²Remove loose labels before inserting tapes.
²Do not leave tapes in the cassette player for a
long time when not being played.
RADIO FREQUENCY INFORMATION
The Federal Communications Commission (FCC)
and the Canadian Radio and Telecommunications
Communications (CRTC) establish the frequencies
AM and FM stations may use for their broadcasts.
Allowable frequencies are:
AM 530, 540±1600, 1610 kHz steps
FM 87.9, 88.1±107.1, 107.9 Mhz steps
Not all frequencies are used in a given area.
RADIO RECEPTION FACTORS
Three factors can affect radio reception:
²Distance/strength. The further an FM station
travels, the weaker it is. The listenable range of
the average FM station is approximately 40 km
(24 miles). This range can be affected by ªsignal
com_cassette_and_player.01
com_radio_frequency_info.01
com_radio_reception_factors.01
Radio frequency information
19

modulation.º Signal modulation is a process radio
stations use to increase their strength/volume
relative to other stations.
²Terrain. Hills, mountains and tall buildings
between your vehicle's antenna and the radio
station signal can cause FM reception problems.
Static can be caused on AM stations by power
lines, electric fences, traffic lights, driving under
bridges and thunderstorms. Moving away from an
interfering structure (out of its ªshadowº) returns
your reception to normal.
²Station overload. Weak stations are sometimes
captured by stronger stations when you pass a
broadcast tower. A stronger station may
temporarily overtake a weaker station and play
while the weak station frequency is displayed.
The audio system automatically switches to single
channel reception if it will improve the reception of
a station normally received in stereo.
Radio frequency information
20

AM/FM select .............. 7
Antenna, radio (see
Electronic sound
system) ........................ 6
Bass adjust ................ 11
CD select ................... 12
Clock
setting the clock ..... 15
Compact disc changer
care .......................... 18
Compression adjust .. 14
Dolbyt
noise reduction ....... 14
Fast forward function 13
Power button .............. 7Radio frequency
information .............. 19
reception ................. 19
Scan function ............ 10
Seek function .............. 9
Shuffle mode ............. 14
Speaker balance
adjust ......................... 11
Stations
selecting .................. 10
Tape direction
select .......................... 13
Tape select ................ 12
Treble adjust ............. 11
Tune adjust ................. 8
Warranties
radio ......................... 21
Index
22