MINI 3 door 2016 Owner's Manual

Page 141 of 258

TiresizeThe parking position may vary depending on
the tire size.
Malfunction A Check Control message is displayed.
The parking assistant failed. Have the system checked.Seite 141DrivingcomfortCONTROLS141
Online Edition for Part no. 01 40 2 972 313 - VI/16

Page 142 of 258

ClimatecontrolVehiclefeaturesandop

Page 143 of 258

Climatecontrolfunctionsindetail
Switchingthesystemon/off Switchingon
Set any air volume.
Switchingoff Turn wheel for air quantity to the
left until the control switches off.
Temperature Turn the ring to set the desired
temperature.
Airconditioning
The air in the vehicle's interior will be cooled
and dehumidified and, depending on the tem~
perature setting, warmed again.
The vehicle's interior can only be cooled with
the engine running.
Press button.
Air conditioning is switched on or off.
Depending on the weather, the windshield may
fog up briefly when the engine is started.
The air conditioner produces condensation wa~
ter, refer to page 166, that will exit from below
the vehicle.
Recirculated-airmode You may respond to unpleasant odors or pollu~
tants in the immediate environment by tempo~
rarily suspending the supply of outside air. The
system then recirculates the air currently within
the vehicle.Press button repeatedly to select an operating mode:'

Page 144 of 258

Defrostswindowsandremoves
condensation
Direct the air distribution toward windows, in~ crease the air flow and temperature, and, if
needed, use the cooling function.
Windshielddefroster Press button.
The front window defroster switches
off automatically after a certain period of time.
Rearwindowdefroster Press button.
The rear window defroster switches off
automatically after a certain period of time.When GREEN Mode, refer to page 173, is acti~
vated, the heater output is reduced.
Microfilter
In external and recirculated air mode the mi~
crofilter filters dust and pollen from the air.
This filter should be replaced during scheduled
maintenance, refer to page 213, of your vehi~
cle.
Automaticclimatecontrol
1Temperature, left2Display3Air flow, AUTO intensity4AUTO program5Air distribution, manual6Display7Temperature, right8Seat heating, rightps 52Seite 144CONTROLSClimatecontrol144
Online Edition for Part no. 01 40 2 972 313 - VI/16

Page 145 of 258

9Maximum cooling10Air conditioning11Automatic recirculated-air control/recircu~
lated-air mode12Rear window defroster13Windshield defroster14Defrosting windows and removing conden~ sation15Seat heating, leftps 52Climatecontrolfunctionsindetail
Switchingthesystemon/off Switchingon
Set any air volume.
Switchingoff Turn wheel for air quantity to the
left until the control switches off.
Temperature Turn the ring to set the desired
temperature.
The automatic climate control reaches this temperature as quickly as possible, if neededby increasing the cooling or heating output,and then keeps it constant.
Do not rapidly switch between different tem~
perature settings. The automatic climate con~ trol will not have sufficient time to adjust theset temperature.
Coolingfunction The air in the car's interior will be cooled and
dehumidified and, depending on the tempera~
ture setting, warmed again.
The car's interior can only be cooled with the engine running.Press button.
Air conditioning is switched on or off.
Depending on the weather, the windshield may
fog up briefly when the engine is started.
The cooling function is switched on automati~ cally with the AUTO program.
When using the automatic climate control, con~
densation water, refer to page 166, develops
that exits underneath the vehicle.
Maximumcooling Press button.
The system is set to the lowest temper~
ature, optimum air flow and air circulation
mode.
Air flows out of the vents to the upper body re~
gion. The vents need to be open for this.
The function is available with external tempera~
tures beyond approx. 32 

Page 146 of 258

page 146, are automatically also switched on
in the AUTO program.
To switch off the program: press the button
again or manually adjust the air distribution.
IntensityoftheAUTOprogram
With the AUTO program activated, the auto~
matic intensity control can be changed.
Turn the ring to set the desired
intensity from soft to intensive.
The set intensity is displayed via the position of
the illuminated LED segment.
Automaticrecirculated-aircontrol/
recirculated-airmode
You may react to unpleasant odors or pollu~
tants in the immediate environment by tempo~
rarily suspending the supply of outside air. The
system then recirculates the air currently within
the vehicle.
Press button repeatedly to select anoperating mode:'

Page 147 of 258

The front window defroster switches off auto~
matically after a certain period of time.
Rearwindowdefroster Press button.
The rear window defroster switches off
automatically after a certain period of time.
When GREEN Mode, refer to page 173, is acti~
vated, the heater output is reduced.
Microfilter/activated-charcoalfilter In external and recirculated air mode the mi~
crofilter/activated charcoal filter filters dust,
pollen, and gaseous pollutants out of the air.
This filter should be replaced during scheduled
maintenance, refer to page 213, of your vehi~
cle.
Ventilation
Setting The air flow directions can be individually ad~justed:'

Page 148 of 258

3."Timer 1:" or "Timer 2:"4.Set the desired time.
ActivatingtheactivationtimeOn the Control Display:
1. "Settings"2."Climate"3."Activate timer 1" or "Activate timer 2"
The symbol on the automatic climate con~
trol lights up when the switch-on time is acti~
vated.
The symbol on the automatic climate con~
trol flashes when the system has been switched
on.
The system will only be switched on within the next 24 hours. After that, it needs to be reacti~
vated.
Seite 148CONTROLSClimatecontrol148
Online Edition for Part no. 01 40 2 972 313 - VI/16

Page 149 of 258

InteriorequipmentVehiclefeaturesandop

Page 150 of 258

for approximately 20 seconds until the LED
on the interior rearview mirror flashes. This
erases all programming of the buttons on
the interior rearview mirror.3.Hold the hand-held transmitter for the sys~
tem to be controlled approx. 1 to 3 in~
ches/2.5 to 8 cm away from the buttons of
the interior rearview mirror. The required
distance depends on the manual transmit~
ter.4.Simultaneously press and hold the button
of the desired function on the hand-held
transmitter and the button to be program~
med on the interior rearview mirror. The LED on the interior rearview mirror will be~
gin flashing slowly.5.Release both buttons as soon as the LED
flashes more rapidly. The LED flashing
faster indicates that the button on the inte~
rior rearview mirror has been programmed.
If the LED does not flash faster after at least60 seconds, change the distance betweenthe interior rearview mirror and the hand-
held transmitter and repeat the step. Sev~
eral more attempts at different distances
may be necessary. Wait at least 15 seconds
between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior rearview mirror button
and repeatedly press and release the hand-
held transmitter button for 2 seconds.6.To program other functions on other but~
tons, repeat steps 3 to 5.
The systems can be controlled using the interior rearview mirror buttons.
Specialfeatureofthealternating-code
wirelesssystem
If you are unable to operate the system after
repeated programming, please check if the sys~ tem to be controlled features an alternating-code radio system.
Read the system's operating manual, or press
the programmed button on the interior rear~ view mirror longer. If the LED on the interior
mirror starts flashing rapidly and then stays lit constantly for 2 seconds, the system featuresan alternating-code radio system. Flashing and
continuous illumination of the LED will repeat
for approximately 20 seconds.
For systems with an alternating-code radio sys~
tem, the universal remote control and the sys~
tem also have to be synchronized.
Please read the operating manual to find out how to synchronize the system.
Synchronizing is easier with the aid of a second
person.
Synchronizing the universal remote control
with the system:1.Park the vehicle within range of the re~
mote-controlled system.2.Program the relevant button on the interior rearview mirror as described.3.Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.4.Hold down the programmed button on the interior rearview mirror for approximately
3 seconds and then release it. If necessary, repeat this step up to three times in order
to finish synchronization. Once synchroni~ zation is complete, the programmed func~
tion will be carried out.
Reprogrammingindividualbuttons
1.Switch on the ignition.2.Press and hold the interior rearview mirror button to be programmed.3.As soon as the interior rearview mirror LEDstarts flashing slowly, hold the hand-heldtransmitter for the system to be controlledapprox. 1 to 3 inches/2.5 to 8 cm away
from the buttons of the interior rearview mirror. The required distance depends on
the manual transmitter.Seite 150CONTROLSInteriorequipment150
Online Edition for Part no. 01 40 2 972 313 - VI/16

Page:   < prev 1-10 ... 101-110 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 ... 260 next >