MINI 5 door 2016 Owner's Manual

The indicator lamp in the instrument
cluster is illuminated, when the low
beams are switched on.
The high beams are switched on and off auto~ matically.
The blue indicator lamp in the instru~
ment cluster lights up when the system
switches on the high beams.
Deactivating The High-beam Assistant is deactivated when
manually switching the high beams on and off, refer to page 70.
To reactivate the High-beam Assistant, press
the button on the turn signal lever.
System
limits The High-beam Assistant cannot serve as asubstitute for the driver's personal judgment ofwhen to use the high beams. Therefore, man~
ually switch off the high beams in situations
where required to avoid a safety risk.
The system is not fully functional in the follow~
ing situations, and driver intervention may be
necessary:'

Interior
lights
General
information Depending on the equipment, the interiorlights, footwell lights, entry lamps, and courtesy
lamps are controlled automatically.
Thumb wheel for the instrument lighting con~trols brightness of some of these features.
Overview1Interior lights2Reading lights3Ambient light
Switching
the
interior
lights
on
and
off Press button.
To switch off permanently: press the button for
approx. 3 seconds.
Switch back on: press button.
Switching
the
reading
lamps
on
and
off
manually
Press button.
Reading lights are located in the front next to
the interior light.
Ambient
light
Depending on your optional features lighting can be adjusted for some lights in the interior.
Activating/deactivating
On the Control Display:1. "Settings"2."Lighting"3."Ambient:"
Settings are stored for the profile currently
used.
Changing
color Push the switch forward or back:
manual color change.
Push and hold the switch forward or
back: automatic color change. Push
the switch again to end color changes.
Setting
the
brightnessDepending on the equipment, the brightness of
the ambient light can be adjusted via the thumbwheel for the instrument lighting or on
the Control Display.
On the Control Display:
1. "Settings"2."Lighting"3."Brightness:"4.Adjust the brightness.Seite 102CONTROLSLights102
Online Edition for Part no. 01 40 2 972 313 - VI/16

SafetyVehicle
features
and
op

Ejection
MitigationThe head airbag system is designed as an ejec~
tion mitigation countermeasure to reduce the
likelihood of ejections of vehicle occupants
through side windows during rollovers or side
impact events.
Knee
airbag
The knee airbag supports the legs in a frontal
impact.
Protective
action
Airbags are not triggered in every impact situa~ tion, e.g., in less severe accidents or rear-end
collisions.
Information
on
optimum
effect
of
theairbags
WARNING
If the seat position is incorrect or the de~
ployment area of the airbags is impaired, the airbag system cannot protect as intended ormay cause additional injuries due to triggering.There is a risk of injuries or danger to life. Fol~
low the information on optimum protective ef~ fect of the airbag system. '

Functional
readiness
of
the
airbag
system
Safety
information WARNING
Individual components can be hot after
triggering of the airbag system. There is a risk
of injury. Do not touch individual compo~
nents. '

'

there is a significant loss of pressure in one or
more tires. For this purpose, sensors in the tire
valves measure the tire inflation pressure.
General
information With use of the system observe further infor~
mation found under Tire inflation pressure, re~ fer to page 186.
Functional
requirements The system must have been reset with the cor~
rect tire inflation pressure; otherwise, reliable
signaling of tire pressure loss is not assured.
Reset the system after each adjustment of the
tire inflation pressure and after every tire or
wheel change.
Always use wheels with TPM electronics to en~ sure that the system will operate properly.
Status
display The current status of the Tire Pressure MonitorTPM can be displayed on the Control Display,
e.g., whether or not the TPM is active.
On the Control Display:1. "Vehicle info"2."Vehicle status"3. "Tire Pressure Monitor (TPM)"
The status is displayed.
Status
control
display Tire and system status are indicated by the
color of the tires and a SMS text message on
the Control Display.
All
wheels
green System is active and will issue a warning based
on the tire inflation pressures stored during the last reset.
One
wheel
is
yellow A flat tire or major drop in inflation pressure in
the indicated tire.
All
wheels
are
yellow
A flat tire or major drop in inflation pressure inseveral tires.
Wheels,
gray The system cannot detect a flat tire due to a
malfunction.
Status
information The status control display additionally shows
the current tire inflation pressures. It shows the actual values read; they may vary dependingon driving style or weather conditions.
Reset
the
system
Reset the system after each adjustment of the
tire inflation pressure and after every tire or
wheel change.
On the Control Display and on the vehicle:1. "Vehicle info"2."Vehicle status"3. "Perform reset"4.Start the engine but do not drive off.5.Reset the tire inflation pressure using
"Perform reset".6.Drive away.
The tires are shown in gray and the status is displayed.
After driving faster than 19 mph/30 km/h for a
short period, the set tire inflation pressures are accepted as reference values. The resetting
process is completed automatically while driv~
ing. After successful completion of the reset,
the tires appear in green on the Control Display
and "Tire Pressure Monitor (TPM) active" is dis~
played.
The progress of the reset is displayed.
You may interrupt this trip at any time. When
you continue the reset resumes automatically.
Seite 107SafetyCONTROLS107
Online Edition for Part no. 01 40 2 972 313 - VI/16

Messages
Required
tire
inflation
pressure
check
message
A Check Control message is displayed.'

Check the air pressure in all four tires, e.g.
using the tire pressure gage of a tire repair kit.
If the tire inflation pressure in all four tires is correct, the Tire Pressure Monitor may not
have been initialized. In this case, initialize
the system.
If identification of flat tire damage is not
possible, please contact a dealer

flation pressure is reduced when the tire tem~perature falls again. These circumstances maycause a warning when temperatures fall very
sharply.
The system cannot indicate sudden serious tire damage caused by external circumstances.
Malfunction The yellow warning lamp flashes and
then lights up continuously. A Check
Control message is displayed. No flat
tire or loss of tire pressure can be detected.
Examples and recommendations in the follow~ing situations:'